Transparent Casting Resins Part 1
Loading...
Link to this comment:
Uploader Comments (davidboddie)
All Comments (9)
-
Could i make up a cup of the clear resin, then brush it ontop of something else to protect the paint job? like another piece of urethane?
-
Took your advice about putting my tin cured molds into the oven and just ruined about 200+ dollars worth of molds. They softened, bubbled, feel like you could put your finger through them, and are completely discolored now. Totally distraught..
-
Where can iget this product?
-
1st class video. THANKS!
-
Would it be worthwhile to put the poured mould into a vacuum chamber to remove all of the bubbles?
-
Great video!
How was the largest piece (hollow skull?) made in the beginning of the video? Slush cast?
-
Great video!
How was the largest piece (hollow skull?) made in the beginning of the video? Slush cast?
-
Is there any way to get a link for a similar vacuum chamber. very cool vid. thanks
5:22
How To Encapsulate Insects In Resinby pyroneph20,697 views- 3:41
Transparent Casting Resins Part 2by davidboddie3,818 views
- 7:19
Cast embedments in Clear Resinby tapplastics206,412 views
- 0:43
Resin Paper Weightsby weegemsjewellery13,830 views
- 10:27
Pressure casting resin with Cindy at resinobsession.comby FunkyTreasures8,626 views
- 9:07
Flexible Molding Foams & Intergral Skin Flexibel Foam Demonstrationby davidboddie8,430 views
- 1:22
Homemade Vacuum Chamberby fezwell1016,484 views
- 9:24
modelcraft 1/43 part 2 Mold making Silicones casting, kits, mold making,by matemail12,488 views
- 13:44
Resin eye (fursuit eye) Casting Tutorialby FurryEcho12,188 views
- 7:29
HydroSpan 100 Enlarging Polymerby davidboddie9,745 views
- 5:21
Rigid Casting Urethanes ProtoCast 80Rby davidboddie4,150 views
- 1:51
Use these two great tips when working with resin.by macaroniandglitter10,119 views
- 1:36
Ultrasonic Removal of Air Bubbles from Epoxy Resinby IndustSonomechanics9,303 views
- 7:56
HyroSpan 400 Shrinking Resinby davidboddie2,863 views
- 6:54
Mold Making and Resin Casting Your Own Sculpted Miniatures - Part 2by XanderXereus77,555 views
- 3:04
Resin jewelry - Julyby sjemmie7932,250 views
- 7:04
Updated - Simple Silicone Rubber Molds (no parting line)by freemanmfg106,982 views
- 3:25
How To Use Alumilite's RC-3 casting resin (for making climbing holds)by AlumiliteCorporation42,817 views
- 4:21
Mold Making - Urethane Rubber Moldsby freemanmfg120,461 views
- 6:21
How To Make Resin Table Top Part 2by tapplastics64,104 views
Heating a silicone rubber mold to 140 to 160 F for 2 to 3 hours should not damage it. For casting urethane clears it is best to begin with a platinum cured silicone type rubber mold where there is no need to dry the mold with heat. Heating a mold helps drive off moisture which causes surface bubbles.
davidboddie 6 months ago
You could put the entire mold filled with casting resin in the vacumm chamber for a while, but you should not let it cure under vacumm. Vacumm makes bubbles larger,
so let off the vacumm after a few minutes before the resin begins curing.
davidboddie 7 months ago