PHOENIX SYSTEMS V12-DIY BREAK BLEEDER INSTRUCTION VIDEO BY STACEY DAVID
Loading...
Loading...
12,215
Loading...
Uploaded by jducs on Feb 26, 2010
This is the instructional video included with the Phoenix System's RFI ( reverse fluid) brake bleeder model V12-DIY.
- 14 likes, 1 dislikes
-
- 2:02
How To:Use Brakebleederby brakebleeder4,996 views
- 0:31
How To:Change Brake Fluid in Ten Minutes or lessby brakebleeder3,736 views
- 4:15
How to bleed brakes using the " One person " methodby backyardmech39,477 views
- 9:58
How to reverse bleed a braking systemby thejunkman3,687 views
- 4:59
Cheap 'n Easy Vacuum Pumpby DerSpark27,382 views
- 4:21
New Brake Toolsby craig197450,448 views
- 3:41
How to bleed brakes by yourself? Introducing The Wizard 1.by thewizard1tool113,845 views
- 2:53
PowerBleeder - The easy way to bleed your brakesby 894638731,993 views
- 2:42
Stacey David uses CHASSIS SAVER™ on Ted Nugent's Rusty Broncoby magnetpaints113,999 views
- 4:26
How to bleed brakes with a brake bleeder. Bleeding rear master cylinder on Motorcross bike.by Johnnysshop37,352 views
- 1:45
Howto bleed brakes yourselfby gcooln33,991 views
- 5:24
Reverse bleeding ATV brakesby sanny65112,095 views
- 1:59
Motive Brake Power Bleeder - What's in the Box?by rallysportdirect19,171 views
- 1:41
brake fluid compressorby fizzygizmos12,978 views
- 3:56
Stacey David's Gearz and Edwards 55 Ton Ironworkerby EdwardsMfgCo4,451 views
- 5:57
Performance Upgrades GSX-R750 Bleeding Brake Linesby OnTheThrottleTV14,288 views
- 9:55
Motorcycle Brake Bleeding Procedure from Sportbiketrackgear.comby Sportbiketrackgear116,506 views
- 7:29
Bleeding Brakes using the Mityvac MV6835by lincolnindustrial4,574 views
- 1:05
HEX Brake Bleed Bottleby gs911tool6,455 views
- 3:20
Buy Brakes Brake Bleeder - How to Bleed your Brakesby TruckXLInc16,873 views
@Tessijia thx for the info, im about to buy this, how would you rate it besides as a vacuum tool? is it worth buying to replace brake and clutch fluid?
eric31291 2 weeks ago
@NUMBER1MrSHOWTIME- For your 1963 VOLVO; first step; drain all fluids; Brakes,Clutch, Coolant, Oil, Gear Lube, the lot. Refill all with new; even fuel. Second;remove all spark plugs and spin motor; first by hand, then with starter. Spin motor with plugs removed until you have oil pressure. Replace ANY rubber hose that looks questionable. Bleed your brakes. Obviously. Install plugs. Start engine and check for leaks. It may be necessary to have the carburettor(s) massaged/adjusted.
ThePatUltra 2 months ago
I HAVE A 1963 VOLVO and it hasnt been started in 20 years! what do you recoment me doing before starting?
NUMBER1MrSHOWTIME 3 months ago
@Tessijia use some thread sealant on your bleeders before you install them, and don't back the screws out so far. You just need to back the bleeder out enough so that fluid comes out in a pretty good stream when you push on the brake pedal - this is usually around 1/4 to 1/2 turn from fully tightened.
dannysauer 3 months ago
They say this tool can be used to vacuum bleed the system but air leaks around the bleeder screw making this method impossible. I emailed them and technical department said " this tool is not a vacuum tool it is a positive pressure tool meant to put fluid into the bleed screw back to the master cylinder"
Tessijia 7 months ago