HHO Smacks Booster 2 LPM using PWM

To prevent over heating I am using a PWM circuit I created.

Category:

Science & Technology

Tags:

• HHO
• Smacks
• Booster
• PWM
• LPM

[rickfish52]

All this shows is that you have a bouncing ball that reads 2 lpm and 0 lpm. You will have to do a bottle test to show a real read out of the gas since you are getting a bouncing ball of course 555 opposite would smooth out that also.

[wwwtacnalcom]

Rick, you are correct! Additionally the flow gage I was using is for AIR not hydroxy so, the best test is a displacement test. I have done many and will make a video if you wish. I am displacing just under 2LPM with this cell and NO PWM.

Using the PWM I am displacing slightly less but I don't over heat.

[electric789]

why is teh flow meter jumpin like that? can you put 2 PWMs pulsing 180 degrees from each other to make the flow a little more moderated, or less jumpy? or am i missing something.

[wwwtacnalcom]

I could do 2 PWM as long as I had two cells. The point of the PWM is to prevent runaway heat.

If you ran two smacks in a 4" PVC T then you could wire both to its own PWM and fire them off 180 deg apart to smooth the gas. I think if you fired one booster with two PWM you might get run away heat.

[rickeygottheblues]

were did you get the flow meter cant seam to find one thanks great job on your cell

[wwwtacnalcom]

I got it from a friend. Sorry

[davidrrrd]

im looking for an update, how far did you get with HHO in your wifes 2007 dodge minyvan?

any MPG's??

[john29302]

yeah what about 2 liters per minute? before you control the current, you ever consider where the heat is coming from? efficiency is the problem and pwms just compensate for inneficiency. what would possess a man to create heat and then limit it? hydrolysis doesnt require heat, thats the sign that you have more than 1.65 volts per plate. that was proved in like 1825. and leakage, naw, smack boosters aint just gas, its vapor and waste of current (yes i have one, nice try)

[john29302]

musta prepped and conditioned the plates and most trucks have 14.5 volts with ripple, thats cuz all chargers have peak ripple (unless you are ignorant of basic charging facts) anyways how much is vapor? vapor is spent water and has to be condensed to squeeze any energy out of it. vapor is present with heat produced by leakage. guess what? thats from Bob Boyce, geee...what does he know? uh...3.5 mmw is smacks booster, 60% efficient, no matter what volume of stuff you measure or how you boast

[ezspool]

sorry dude unless it is calibrated for hho it IS not accurate, bottle test that bad boy.

[pinoykunat]

Thanks for sharing, what is your solution and ratio? The wires are not getting hot? My wires seems to get hot after 15 minutes of testing under 12 amps and 12 volts. Your help is very much appreciated. Thanks

[john29302]

instead of pwm a diode in series would create .6v times say 20 amps of 20.6 watts loss making voltage 13.8-.6 =13.2v ...wouldnt a simple switch reducing say a couple or three diodes make the cell reduce heat and current draw drop where you want it to?

[minde4000]

Ya displacement video will do it. And someone else is right it jumps sometimes above 2L because of inertia since it is being bumped up pretty quick and after all average of that bouncing should be some 1L+. So lets get rid of creepy stuff and measure right (correct output). Tnx

[milosbone]

Hey smack great VID's! I new to the you tube exspereince but have been following the achivements of many through the years, I was in const all my life and should have been in science so i know LITTLE! I need schematics to build a PWM that I can read on the computor or have someone send me The ones I have been able to down load so far Are WAY to complicated for me and the ones that are not are too blurry to BET on doing RIGHT. any help would be GREAT!