AR-MPR AR-15 Build: Upper Part 1: Ejection Port Cover and Forward Assist
Loading...
Loading...
8:54
AR-MPR AR-15 Build: Upper Part 2: Barrel, Gas Block, Gas Tubeby gavintoobe42,832 views- 4:28
$550 budget ar-15 buildby mrazyattic25,994 views
- 7:27
SWIMMMMING in icey cold waterby Tjpinkgurl2,902,119 views
- 0:40
M4 blows up after being fired filled with waterby stevejohnson07614,808 views
- 7:33
AR-MPR Phase III Hornady Lock-N-Load Loading 223by gavintoobe13,480 views
- 6:39
Hornady Lock-N-Load Bullet Feeder Loading 45 ACPby gavintoobe40,450 views
- 23:46
Build Your Own Custom AR-15: Part 1by MrSurgicalPrecision12,890 views
- 20:10
AR-15 Upper Receiver Build - how to build an AR 15by SoCalPreppers16,838 views
- 9:19
Custom AR-15 build, BADASS ZOMBIE KILLING RIFLEby jamoore319235,652 views
- 8:49
AR-MPR interactive AR-15 Build - Tools needed to build an AR-15 - UltimateReloader.comby gavintoobe16,531 views
- 8:05
WorkBench Tour (as requested)by weaponeer5,583 views
- 2:12
AR-308-Kick-Off on UltimateReloader.comby gavintoobe3,425 views
- 2:00
Installing Takedown Pin and Buffer Tube - Building your AR-15 - CheaperThanDirt.comby CheaperThanDirtVideo43,048 views
- 1:36
DIY Coloring AR15 Lower Receiverby TheGunGroup27,082 views
- 4:58
Simple Upgrades for Your AR15by millerusaf51,317 views
- 1:31
AR Free Float Tubes - How to Installby MidwayUSA169,010 views
- 0:50
M2 Failure (headspace and timing)by bluecord11b55,828 views
- 9:25
AR15 Build Lower Receiverby ammosmith16,377 views
- 0:27
Quick Magazine Changeby Vagitarian132,446 views
- 8:38
AR-MPR Phase II - Charging Cases with Redding 3-BR and Hornady Auto Chargeby gavintoobe3,872 views
Very helpful videos. Well done. Thanks!
TheTogliat 2 weeks ago
What camera was this shot with? Amazing quality even at 480p!
McGTexas 1 month ago
hey bud really liike the vids.
mjmoto72 4 months ago
@edd217 It allows you to seal the bolt forward if it is fouled and doesn't close properly, which would lead to a failure to fire.
Pantera40z 4 months ago
Great vid; my son and I watched a couple times and pop, were done; thx.
michaelsmith024 5 months ago
Very informative, and very well executed, but one solid piece of advice from gunsmith to gunsmith when installing a roll pin with a guide punch, just get the pin started, try not to continue hammering it in with that punch, I've seen a few of my counter parts chip off the ends, and bust those punches pretty bad, i suppose it is a double edge sword tho, either that or you mushroom head the pin, and using a plastic hammer only tears up the end of the hammer.
midnightraven00 6 months ago
@edd217 if you put in a new mag and release the bolt, but it doesnt go all the way forward because the round is a little stiff, you push on the forward assist to force it into place.
jimmyhoffa9 7 months ago
great video
usmccapdevil 8 months ago
do you need to take apart the entire barrel off to install?
gabebokmaUSMC 9 months ago
I lost that damn c clip today. Fuck me.
ih8suvz 9 months ago 2