7# HHO-Geet Pantone Hybrid testing
Loading...
Uploader Comments (aluka1603)
Video Responses
All Comments (8)
-
@aluka1603 No Problem, Please I could offer advice :-) By using higher flowing tubing for the bubbler means you won't have to use the valve after the reaction chamber to control the mixture (by making it leaner). You can control the revs by using a valve before the bubbler to control all of the intake flow and enable all of the intake air to go through the reaction chamber.
-
rainmanp7 aka cryogenics
The more vapor the better. Try my KML wire :) I made the wire jsut for the geet and hho production. Very good work friend :) I'm looking to buy a reactor at this time ,because I can't weld ,but i definatly know how the device works :) I t does definatly work..... try putting hho through it :) maybe use a generator of sorts to pump hho? add a little we bit of soap and break down the bubbles?
-
When you put the ball magnet on the end of the rod did you see the performance get better or worse or no change?
When you put the spiral weld on the outside of the inner pipe did you see the performance get better or worse or no change?
Thanks, Naresh
-
Thanks for all the good information. It is very interesting to see how the experimenting is going.
-
Good job!!!
5:39
8# HHO-Geet Pantone Hybrid testingby aluka16037,319 views- 5:18
9# HHO-Geet Pantone Hybrid testingby aluka16035,639 views
- 3:28
Geet Plasma HHO Motor Teil 3 ( Deutsch) by alukaby aluka160345,406 views
- 8:46
Geet Plasma Motor Teil 2 ( Deutsch) by alukaby aluka160317,674 views
- 2:28
5# HHO-Geet Pantone Hybrid testingby aluka16034,308 views
- 1:07
Diesel- Run Car On Water Fuelby jouksonli20,899 views
- 0:29
Assembling a GEET reactor - Part Iby JohnsEngine26,000 views
- 5:38
GEET Reactor Construction Detailsby narivasant93,963 views
- 7:37
Part 2 The evolution process to the source of Murray's ultra efficiencyby syncopetra31,914 views
- 9:30
1# HHO- Geet Pantone Hybrid testingby aluka160333,566 views
- 0:27
The deepest hole in the world!!!! (20+ seconds to the bottom)by GEOCACHINGJEFF5,379,078 views
- 0:05
Simple gas feed system to GEET bubblerby 2550osiosterdalen6,013 views
- 3:44
GEET Fuel Processor - test 2by neverchk10,462 views
- 8:55
Paul pantone geet plasma caught beeing formed through sight glassby servall130,944 views
- 4:16
GEET Fuel Processor - test 4 - revelationby neverchk112,499 views
- 4:13
GEET, Motor de Plasma con Agua 2º (Español)by aluka160319,291 views
- 2:05
GEET CAR PANTONE SETUPby clackdwack57,339 views
- 4:26
Pantone GEET Multi-Fuels Processor #1by answerfreak156,730 views
- 1:53
GEET Project 090409by richardday1,798 views
- 0:30
Paul Pantone GEET Tornado Bubblerby narivasant16,823 views
Sorry for all of the suggestions but I'd say you are seriously limiting your performance with the size of the tubes you are using for the bubbler. they should be *at least* as big as the hose you use for the inlet to the carb fitting, if not bigger. You're seriously restricting the air flow. Keep up the good work!
carlhutchinsondotcom 2 months ago in playlist More videos from aluka1603
@carlhutchinsondotcom I came to the same conclusion as well but had no time to put all the details here. Thank you Carl because it will help a lot to make it better, you are complety right !
aluka1603 2 months ago
@narivasant, It is an honour to have you here "MR- GEET" i Admire your work!Thank you for sharing your knollege.
aluka1603 3 years ago