5'x10' Torchmate X with Thermal Dynamics Ultra-Cut 300 and Gas Box.mp4

This is a video of one of our 5x10 Torchmate X Water Tables cutting .060" mild steel at 250 inches per minute using a Thermal Dynamics Ultra-Cut 300 with Automated Gas Box. For details call (866)571-1066 or email us at sales@torchmate.com

Category:

Science & Technology

Tags:

• torchmate
• cnc
• plasma
• cutter
• cutting
• table
• water
• thermal
• dynamics
• ultra
• cut
• ultracut
• mild
• steel
• circle
• rectangle
• cold
• roll
• rolled
• metal
• fabrication
• fabricate

[Simonh1959]

What is the reason for the waterbath & does it not cause problems with rusting of mild steel material?

[torchmatedotcom]

@Simonh1959 The waterbath eliminates most of the dust and debris from entering the air from the plasma cutting process. Since the table is powder coated their isn’t much need to protect the table from rusting. The slats however will start rusting once the water is removed, but it isn’t bad. Cutting steel that has a mill scale won’t rust if left on the table but if you use steel that has the scale removed the material will start rusting if not dried off.

[counterjb]

TENGO UNA PREGUNTA VOY A INTENTAR HACERME ENTENDER. DIGAMOS Q LA MESA TIENE LA CAPACIDAD PARA CORTAR UNA LAMINA DE 300MM X 400MM Y LA MESA ESTA HECHA PARA UNA LAMINA DE 2000MMX4000MM UN EJEMPLO- COMO AGO PARA CENTRAR EN LA MESA ESE PEDACITO DE LAMINA Y Q CUANDO YO META EL PEDACITO DE LAMINA COMO SABE LA MAQUINA DONDE YO PUSEE ESE PEDASITO DE LAMINA... QUE HAY UNOS TOPES O UNAS MARCAS EN LA MESA PARA SABER DONDE COLOCARLA O QUE????? NOCE SI ME LOGRE DAR A ENTENDER ESO ES UNA DUDA QUE SIEMPRE TUV

[torchmatedotcom]

@counterjb La mesa está para que tu inicio de corte o punto 0.00 esta en cualquier lugar de la mesa. Simplemente tienes que colocar la antorcha en el punto que quieras o en la parta inicial de la lámina y ese va a hacer tu punto 0.00 (colocar en el softaware Zero all), Dejanos saber si entendiste el procedimiento.

[mephud]

@Simonh1959 The smoke that is released is terrible and Will give you alzheimer's

[torchmatedotcom]

@121ego we only provide them on TMX turnkey tables and they are just hot roll 3/16 flat bar.

[121ego]

@torchmatedotcom - why do you power coat the slats? They would fill with plasma dust (or become cut and damaged by the arc) in a shorter time it will rust.

[121ego]

@counterjb - Dependiendo del controlador de la maquina, este - al encenderla por primera vez - toma sentido de donde esta colocado, y - al mover tu el carro en cualquier direccion - toma cuenta de los dos parametros x, y, y cuando mueves el carro a donde has colocado tu plancha de metal. empieza a "contar" las movidas desde esa posicion.

[torchmatedotcom]

@Simonh1959 The waterbath eliminates most of the dust and debris from entering the air from the plasma cutting process. Since the table is powder coated their isn’t much need to protect the table from rusting. The slats however will start rusting once the water is removed, but it isn’t bad. Cutting steel that has a mill scale won’t rust if left on the table but if you use steel that has the scale removed the material will start rusting if not dried off.