Lead-Free SOIC 20 Installation | B.E.S.T Corporation
Loading...
Uploader Comments (SolderingGeek)
All Comments (11)
-
What a crooked, shitty job!
-
olmost all of your vid's are soldering with lead free but does it work's fine with leadded solder to?
-
Hi Norman, is there a reason you wouldn't use drag soldering on this type of chip? I have almost no SMT experience myself.
Also, do you have any special method of soldering a very small TSOT-23 package by hand soldering? I have a need to mount one of these chips on a board and the lead spacing is very fine (.5mm)
I'm currently using a no clean Kester 951 flux along with a small diameter solder (.03) and a fine tip iron set at approx. 550F. Any advice would be appreciated.
-
fix camera, no cuts.. lovely video. tills new videos of yours.. tnx
-
is solder paste flux has side effict if iuse my hand to paste it
-
I like what you are doing very good.
The scrolling wordage was distracting.
3:20
Professional SMT Soldering: Hand Soldering Techniques - Surface Mountby jkgamm041209,761 views- 1:33
Desolder SMD without special toolsby MrKobalts82,472 views
- 0:37
Professional Surface Mount Soldering - How To: QFP 64 (Drag Solder)by jkgamm04153,242 views
- 3:40
SOIC14 Installation | Soldering Tips | B.E.S.T Corporationby SolderingGeek38,355 views
- 1:03
PSP DEVOLUTION SOLDERING FLAT RIBBONby PSPDEVOLUTION96,750 views
- 3:59
TSOP32 Installation Multi-lead | BEST, Inc.by SolderingGeek35,660 views
- 1:59
SMD Reflow Solderingby halfinchhole142,815 views
- 1:13
soldering はんだ付け SSOP16ピン その２by k2denshi11,381 views
- 0:51
DIY: surface mount soldering of 8-SOIC part (SMT pt 1)by aeomoea113,492 views
- 1:57
Solder a 100-pin LQFP SMD-ICby WatterottElectronic64,475 views
- 5:13
Removal of DIP Tweezer Method | B.E.S.T. Inc.by SolderingGeek19,392 views
- 1:57
EZReball Demo Video | New BGA reball method | BEST Inc.by SolderingGeek166,218 views
- 3:01
SMT Soldering 0402 Component/Installationby SolderingGeek27,485 views
- 2:56
TSOP32 Installation Drag Method | BEST, Inc.by SolderingGeek23,351 views
- 0:35
Repair mainboardby apluslamp408,003 views
- 1:36
Soldering SMD 0805 Capacitorby thelastnameavailable189,453 views
- 0:24
Drag solderingby circuittechnology39,359 views
- 3:28
Hand Soldering a .5mm QFP Chip With SchmartBoard|ezby nealgb110,326 views
- 4:16
Lead Free Through Hole Soldering Tips | B.E.S.T Corporationby SolderingGeek26,887 views
- 2:47
Soldering SOIC 16by thelastnameavailable30,104 views
hi, noticed in a lot of your videos that you initially solder one or two of the pins but you are not using solder to tack them down so how do the stick until you start using the solder properly, is there something in the flux that attaches the pins temporarily, how do they "dry tack" ?
thanks
donnyab 2 years ago
Dry tack is using solder that is on the part from tinning it or from solder that is left on the pad after you have prepped the site.
SolderingGeek 2 years ago
very nice
everything was perfect, unlike other people
jmoldowan2021 3 years ago 2
Thank you for your complement
SolderingGeek 3 years ago
Thanks for the comment.
SolderingGeek 3 years ago
It is a Rosin 800 by Alpha Metal. It is a No Clean Flux that I have been using for several of video streams. It gives me better wetting action for lead free solder. The soldering system is OK Industries MX 500 and the tips is a 700 degree set temperature.
SolderingGeek 3 years ago