smk11111's channel
Loading...
-
1 week ago
Bart Sibrel Being Hooked by Buzz Aldrin (Apollo 11)
not bad for 72 y.o. man
keep going, Buzz!
smk11111
commented:
-
1 week ago
China Product Sourcing - Introducing The New EcoBoomer XL
Company Website: http://TheEcoBoomer.com
This is our new EcoBoomer, it's an all electric, zero emissions, environmentally friendly, human trans...
smk11111
commented:
its right. if i had one here, hell, i would use it, cheaper than the car, but then get run over by a lorry, or hit by a car is the next, what i want is a velo. they are covered, stick a electric motor on it, about just enough clearance for the damn speed humps, big wheels to take the pot holes, d...
-
2 weeks ago
Riding the Copenhagen Wheel...
Developed by MIT's SENSEable City Lab, The Copenhagen Wheel turns any bike into a smart electric hybrid with regeneration capabilities and real tim...
smk11111
commented:
if you can see it, error
-
2 weeks ago
Adam Rose - Handcycle Racer
Adam Rose, top handcycle racer in Michigan. Top junior hanndcycle racer in USA.
smk11111
commented:
good one bud. keep it up
-
2 months ago
Bore turning useing lathe bore head and old milling machine
For bore repair it need make little big and then press into bush withe original inner diameter. I use 1930-s Biernatzki milling machine, also I use...
smk11111
commented:
been there. done that. but i would stop the spindle. move away from the tip then bring it back up. i used a Victoria vertical/horizontal. with the same machine i could do gear cutting as well. the good old days. sigh.
-
2 months ago
My 1st Home Built TadPole Trike (funny ending) +++ Video 1-ONE
This is my first attempt at a tadpole trike, and also my first video of who knows how many?? Enjoy
smk11111
commented:
good man. love the pic at the end, and i think thats my mates sister
lol
-
2 months ago
parting off
parting off EN8 35mm dia on the warco mini lathe with a 1.8 mm indexable tip in home made holder..
smk11111
commented:
stick some coolant on it, it helps
-
2 months ago
Small CNC Lathe with 8 position "Automatic Tool Changer"
Full enclosed CNC lathe with 8 position servo turret. Spinlde bore 1 3/8. One horse power 120 volt Vector Drive. "Turret" is locked by air pressure...
smk11111
commented:
similar to emco's, 342t, 342n series, not as small though but can pile out a load of work.
-
-
3 months ago
Ditch the Chain, a New Type of Bicycle Is Here
Trek Bicycle is on the cutting edge of a movement to bury the finger-pinching, pants-munching, rust-prone sprocket and chain, and usher in a new er...
smk11111
commented:
great in Holland, no damn hills
-
4 months ago
Thread Cutting
Cuttin thread at work with heaps of cutting fluid.
smk11111
commented:
he is wearing safty glasses, but certainly needs and extractor for a start
-
4 months ago
Aluminum High Feed Milling 300ipm
Boeing Phantom Works
smk11111
commented:
well. we go a damn sight faster, with a smaller cutter and when the swarf comes off, it chips. and chatter, like hell
-
6 months ago
Facing off on a lathe
Showing the standard method of facing off a piece of bar. The tool is set just a little too high.
smk11111
commented:
better still. look at cutting angles. if cutting plastic, use a near knife edge tool. as with this material u do need to have the tool on the centre line. obvious. but make sure the tool is nearly polished and the cutting angles are sharp. its amazing how a near 60deg angle can make swarf flow aw...
-
6 months ago
Vardex V6 Thread Turning Insert - 6 Cutting Corners
Vargus Presents the Next Generation in Thread Turning Inserts - The 6-Cutting Corner System!!! Learn more at www.vargus.com
smk11111
commented:
good tools. but i was at one time using a quad cut. they were damn good tools for close shoulder threading and lasted damn well, but alas, they got bought up and we got left with just the standard 3 side cutting. this is called progress
-
6 months ago
Turning, Facing, and Grooving lathe tool
One tool for turning, facing, grooving, face-grooving, and cut-off. Significantly reduces tool costs, & Minimizes machining time.
For more informa...
smk11111
liked
-
7 months ago
Big Bad Blackhead
a huge black head XDD!!
im very sorry for the camera being so unfocused
it is because i was looking at it too not realizing
that the camera focus ...
smk11111
commented:
thats just playing with it
had a blackthorn in my leg, now that was something. and brass, im an engineer so u get that in you, you get real puss, i mean septic shit that is bad.
-
7 months ago
Riding to Giessen
Velomobiles on the road to Giessen from Bibertal at the 2005 International Velomobile Meeting. There's a Greenspeed trike, an early yellow Cab-Bik...
smk11111
commented:
well, remember the c5, laughed off because it was dangerous on the british road, the goverments dont want things like this on the road and you wont be able to buy one cheap either.
If u had one of these riding around, within 6 months some asshole will smash into it and say i never saw it.
-
8 months ago
-
8 months ago
Kondia CNC - Crash, 416ss Driver
The beginning of a long day... Finished the run the day before. Just wanted a vid of it. Set up the lights, the camera and then came the action. Tw...
smk11111
commented:
crap happens
-
9 months ago
FULL VIDEO: Copenhagen Suborbitals Rocket Launch (SUCCESS) - Baltic Sea - June 3rd, 2011
SUCCESS! (on the 2nd try) - CONGRATS GUYS!
1. Attempt: FAIL @ 1:53
2. Attempt: SUCCESS @ 5:45
******
Rocket: HEAT-1X/Tycho Brahe.
This is a non...
smk11111
commented:
well done
-
1 year ago
Video Of #CutePiglet Wearing Ballet Shoes Crippling Internet (Do Not Watch - ARCHIVE PURPOSES ONLY)
As reported by ONN (http://onion.com/gHgAWg) this video was part of a second wave Al Qaeda attack on America which began Friday February 25th with ...
smk11111
commented:
what a load of ####
About smk11111's channel
good one bud. the religious asshole provoked him, and i would do the same. Buzz. you are a winner