seanh303's channel

This is a brief tour of my rig (the RM100 has been replaced by a 5150 III for the moment).

A brief description of how to perform a cylinder leak test on an automotive engine and what the results mean.

Engine noises aren't to hard to diagnose if you follow a few steps.

Calipers can be tricky little &@$+@%'s to reassemble if you don't know the trick.

How to check crankshaft thrust or endplay while assembling an engine.

Take a look at this BMW cylinder head that was brought into Costa Mesa R&D Automotive Machine for some re-work. The head was resurfaced by another ...

Huge cloaked UFO next to Mercury on SECCHI HI1-A on 12/01/11, appears when a CME hits it. Go to SECCHI and record this before it disappears.

Here'...

05/11/04 - Associated Press

MEXICO CITY - Mexican Air Force pilots filmed 11 unidentified flying objects in the skies over southern Campeche state...

Mark IV LS7 on run stand, sounds like its ready, sounds freakin awsome....

Good Feeling (Levels Version) Flo Rida ft Avicii [Dark Intensity Remix]

╔═══╗────╔╗──╔══╗──╔╗─────────­─╔╗─────╔╗

╚╗╔╗║────║║──╚╣╠╝─╔╝╚╗────────­╔╝╚...

This is a video showing valve float in a running engine at high RPM.

OTC Hub Grappler™ by OTC

• The Hub Grappler Kit is the complete solution for

servicing wheel hubs and bearings on the vehicle

without removing the...

Anthony & Raj @ DIYautotech taking you through the steps on the Rotler SG-8 on how to properly cut valve seats on your cylinder heads.

If you have...

Rottler SG9 UNIPILOT Seat and Guide Machine boring out old seat inserts and cutting new seat inserts with multi angle cutting insert

John @ Costa Mesa R&D Automotive Machine describes how to replace valve guides on the popular small block Chevrolet cylinder head. www.engine-machi...

Grinding a valve seat for the 1913 C & G Cooper tandem gas engine at Rough and Tumble.

Valve Guide Repair Sleeves Demonstration by Rapid Technologies

This was a project for school, done with an old block, and old valves. we didnt take care and did it fast. so dont bother commenting saying how hor...

Engine Doctor Presents a video on how to polish your crank shaft.

I go into detail as to why i think it is morally wrong to support the troops. Bottom line is the entire military industrial complex would collapse ...

Part 1 of 2 - Bear Carnage Compound Bow Review by Merlin Archery

Download on iTunes - http://itunes.apple.com/ca/...

Download on Juno - http://www.junodownload.com......

MC PROGERIA is like whoaa

http://f2bbs.com/bbs

http://www.youtube.com/user...

Skyline vs Police

Pause at 0:23 for full car of fail.

John Edwards @ Costa Mesa R&D Automotive Machine is reducing reight again, this time on a set of Triumph Spitfire connecting rods, check it out. (9...

Its time for Part 2 of the series on the 1935 Desoto Airflow cylinder head reconstruction, this time John Edwards talks about machining the head fo...

Another race prep modification that is performed by John @ Costa Mesa R&D Automotive Machine is to install a set of ductile iron sleeves in the Sub...

See how connecting rods are balanced by John Edwards @ Costa Mesa R&D, www.engine-machining.com 949-631-6376

A 6-cyl high performance BMW cylinder head being resurfaced on the Sunnen HBS-1300 to correct a warp condition and surface finish measurement with ...

John Edwards discusses the various types of connecting rods found in modern engines. www.engine-machining.com (949) 631-6376