roygpa's channel
Loading...
-
roygpa
uploaded
1 week ago
PTHS 2012 Music and Meatballs Band Front
Recorded on January 20, 2012 using a Flip Video camera.
-
roygpa
favorited
1 week ago
Rotationalmouldingmachine - Marloes ten Bhomer
www.marloestenbhomer.com
After Hours is an installation by Marloes ten Bhomer and presents the step-by-step procedure for making Rotationalmouldeds...
-
roygpa
liked
1 week ago
-
-
roygpa
liked
2 weeks ago
Reprap Project- Full Print Under Funky Lights
I purchased the Dioder from Ikea. It has 4 strips of 7colored LED lights and this is my first print while using them. It saves me from running my h...
-
roygpa
liked
1 month ago
Death Star Lego timelapse build - Christmas 2011
I bought myself a special gift this Christmas, and this is the timelapse of me building it. Approximately 10-12 hours over the course of a few day...
-
Josh Reardon & Lynnsey Garlick singing "I See The Light" at Coffeehouse 2011
Josh Reardon & Lynnsey Garlick are singing a duet of "I See The Light" from the Tangled Soundtrack at Peters Township High School's 2011 CoffeeHou...
-
-
roygpa
subscribed to MakerFaireVideo
2 months ago
-
roygpa
uploaded
2 months ago
Printing a gear
Printing a gear using a DIY Prusa Mendel 3D Printer
-
roygpa
liked
2 months ago
Prusa printing "250mm/s" faster :-D
250mm/s with 4000mm/s^2 acceleration. You can see it way faster then previous video.
Printer can accelerate to that speed on lines atleas 16mm lon...
-
roygpa
uploaded
2 months ago
First print with my Prusa Mendel 3D Printer
roygpa's shared video file.
-
roygpa
liked
2 months ago
-
Still Extruding: Calibrating XY&Z Step/MM
Calibrating the XY&Z axis of a RepRap. If there is any part of a reprap which it is important to be a perfectionist with, it's this.
-
-
roygpa
favorited
2 months ago
Still Extruding: Configuring Sprinter Firmware
In this video we go over the initial setup for Sprinter Firmware. The Configuration.h file is basically the same for marlin and SpribbleJ's firmwa...
-
roygpa
liked
2 months ago
-
-
roygpa
favorited
2 months ago
Still Extruding: Soldering Prusa Heated Build Plate
A overview of what's involved in soldering a Prusa HBP, these are now cheaper than doing a power resistor bed, so I really sugjest you go this rout...
-
roygpa
liked
2 months ago
-
-
roygpa
liked
2 months ago
RepRap - first test with a pencil
Prusa Mendel - first calibration test with pencil.
-
roygpa
favorited
2 months ago
A messy homemade plastics extruder
This is the first test run to see how it works and it works great, just the motor needs to be stronger.
-
roygpa
liked
2 months ago
-
-
roygpa
favorited
2 months ago
Budaschnozzle 1.0 test video
Test video. Budaschnozzle 1.0 printing
-
roygpa
liked
2 months ago
-
-
roygpa
subscribed to LulzBotVideo
2 months ago
-
roygpa
favorited
2 months ago
Sanguinololu: Soldering and testing the SMT FTDI FT232RL chip
A short video of my method of soldering and testing the FTDI chip on the Sanguinololu pcb. http://reprap.org/wiki/Sang....
There is a slight ...
-
roygpa
liked
2 months ago
-
-
roygpa
favorited
2 months ago
Still Extruding: Flats on a Stepper Motor
Some stepper motors come with a flat spot on the shaft to keep the gear from sliding, if they don't you will need to do this yourself. It's not ha...
-
roygpa
liked
2 months ago
-
-
roygpa
subscribed to GeoDroidJohn
3 months ago
-
roygpa
favorited
3 months ago
My Prusa hates me
Printing with .35 nozzle and caruKlip/Klimentkip firmware at 155 mm/s
Photos: https://picasaweb.google.co...
-
roygpa
liked
3 months ago
-
-
roygpa
favorited
3 months ago
Prusa heated bed
How I mounted my heated bed PCB. It keeps it nice and flat using just stuff I had lying around.
-
roygpa
liked
3 months ago
-
About roygpa's channel