ndown15's channel

1/5 scaled down version of the full size Pratt & Whitney R-2800 Double Wasp 18 cylinder radial engine. Although every detail is not exactly to scal...

Starting my old truck after sitting for 26 years with 6V53 detroit engine

http://allcatequipment.com

http://ironmartonline.com

Jay Trevorrow 973-886-3020

79 ford Bronco Big Block

Model brandstof motor Dux Run Brandstof Kero + diesel

Model brandstof motor Dux Run Brandstof Kero + diesel

Plays best at 360p. As seen in the magazine Model Engine Builder. This is the original open six engine with a new intake manifold. It works much be...

My friend really likes dirtbikes, but he just doesn't know how to ride one :D

HUGE engine explosion at a tractor pull event. the block is literally blown out of the engine bay and lands onto the ground next to the tractor. ...

Aussie Musclecar Museum

This video cannot even come close to recreating the spectacle, but we've done our best through the miracle of technology....

Farm Boy after a little break in and fine tuning.

Muscle Car Rescue is a source to report muscle cars that are abused and abandoned. Please go to musclecarrescue.com and report the location and ph...

Various models of cars from ford and chevrolet. Shot in Jerome. Arizona.

Casting ten model cars using a snap flask to make the moulds.

I get a lot of questions about the sand I use. Here is my first attempt at making my own greensand. The results are very good. It was a lot of work...

I am showing a method of casting I read about somewhere, using a cuttlefish bone as the mould. it worked well on a small item. The size of the cast...

How I make cast alloy, lead filled, steel rimed flywheels. Showing how to increase your lathe capacity.

Full casting techniques can be seen on my o...

Beautiful working model of a Case tractor

well I fired up the Model A again for those of you that asked and tried to get it moving for a first drive and so I could get it up to the shop... ...

Machining a 6" scale Burrell Gold medal crankshaft on my Colchester lathe, 20lbs of lead added to help balance it.

Cutting a spur gear for the AL-54B Lathe

This is the tuned up run of my Tiny I 4. After replacing some bushings, adding an oil baffle, replacing some gear train components, and a 260 durat...

Some of the many fails and failures from 2011. (Not all included)

The dozer and scraper are both scratch built.

Check out: http://www.hpieurope.com/ki...

The exciting Baja 5SC SS gets the SS treatment! HPI is proud to announce the...

Clearing grass in a very wet swampy area with Flail Mower on a CAT 289C All Terrain machine

Double burner overhead cam and lots o fun

SPONSORED BY DRINKBOUNCER @ http://www.facebook.com/pag...

Also Join his fan club on acebook @ http://www.fac...

Model of a 1906 "Bill" engine driving a DC generatgor. Operating on propane fuel at approximately 1400 RPM.

Take a peek inside the world of lawnmower racing--where yard cutters become speed demons. Directed by Shaun Irving.

Visit my YouTube channel or w...

Havin fun out the bush with my mates at one of our 4WD days.... GO HARD!!! Before the turbo went on...

Are you a 4wd nut? Request an invitation at 4wdNuts.com.au now!

Great day trip with forum group at Tallarook - 10 cars including:

V8 Shorty GQ, TB...

Flying shop rags were popular after we broke our planes as kids. We were addicted to these Cox glow engines, so we had to run them, just to run the...

The "first pop" of a model internal combustion engine is a big moment for the builder. In this case, over two years of work by builder Tom Boyer wa...

水平対向６気筒エンジンの製作と試運転です。

This is intended as an example of how much power can be produced out of nothing but heat and air density, and how your car's engine has to overcome...