makedoandmend2's channel

Discovery / Science Channel's "How It's Made" Engine Blocks episode

This is a graphical depiction on how it is possible for a man to be his own grandfather. This actually happens and was published in a number of ne...

Lyrics to "I'm My Own Grandpa" by Homer and Jethro, no copyright infringment intended

This video demonstrates how to remove and replace a broken slate to repair a roof along with the important tools to get the job done.

Small informative video on slating your roof

Setting your under eaves, coarsing, up to the apex

(http://www.roofrepairstore.co­m)

Watch 100's more Pacific Island Music Videos at http://www.IslandBeats.TV . Hawaii's Music Legand, Genoa Keawe sings her famous song Papalina Lahil...

for more videos visit our website

http://iceengineeringvideos...

for more videos visit our website

http://iceengineeringvideos...

Agri Supply carries a full line of hydraulic valves for hydraulic cylinders. This video explains some of the types, open and closed systems, and po...

Tubalcain explains the basic parts of the milling machine. This is part 1 of 2 parts.

Tubalcain shows how to turn a V-Pulley on the Clausing lathe.

Part 3 of 3.

SUBSCRIBE TO MY CHANNEL!

SIXTH No1 IN THE U.K.CHARTS. (MARCH/APRIL1953). WRITTEN BY BOB MERRILL.

This song was a UK number 1 hit in 1953 for Guy Mitchell. It was written in 1952 by Bob Merrill and it's about a London banker who goes sailing off...

Roundhead Road, Newton Abbot, Devon, TQ12 6GY, http://www.yell.com/b/K.B+R......

Hill Country Fencing with the Bryce Suma Fence Post Driver.

Website: http://www.brycesuma.co.uk

MACHINE SHOP TIPS #64 Clausing Lathe Gibs Pt 2 tubalcain

Irish tune, written in 1917 by R. P. Weston, Bert Lee, Bob Adams and Bob Allen, performed here in the key of C major. This is the first video I've...

Tubalcain shows how to adjust the compound gibs on the Atlas lathe. Part 2 of 2.

As seen on E-bay

Grinding Endmill on my Clakson MK1 & Weldon Model 200 Endmill sharpening device

A two part series on holding the work in the Bridgeport mill.

Part 2 of 2. Tubalcain verifies the accuracy of the digital readout on the Bridgeport mill.

Tubalcain shows how to accurately layout & ream holes by 3 different methods. part 2 of 2

A short film (6 minutes) telling the story of how a small group of European journalists, researchers and computer programmers uncovered the secrets...

Tubalcain discusses various makes of metal lathes and gives tips on what to watch for when buying a used lathe.

Part 3 of 3

our bill

come back bill

David Cameron refuses to offer British people a referendum on EU membership when quizzed by Bill Cash MP. September 2011

Learn how plasma cutting works in this second video. See the air and arc pass through a torch to make a precision cut. Visit http://www.millerweld...

Combining soybeans with old machinery. Older John Deeres & an Oliver. Taped at the Geneseo , Ill. Steam Show. Sept. 2011

http://www.weldingtipsandtr...

This Precision Welding Table by Stronghand Tools absolutely Rocks. I know most of...

Express delivery from political editor Patrick O'Flynn

Weld

UK Independence Party leader Nigel Farage and Labour Lord Liddel Lord Liddel's pension due in a few years is dependent on his continued support of...

Need a good welding project? Check out http://redwingsteelworkspla... and http://utilitytrailerplans.net

BuildPro Affordable, Modular Welding Tables

Table being loaded in 2 min, ready for tacking and rotating. part is clamped and welded in position.

EVO 2 provides additional equipment that compliments EVO 1. EVO 2 comes with special tools for rear-axle bracket, torque bar extensions and adjusta...

Installation of carrier bearings, pinion bearings, ring and pinion and a crush sleeve are covered in this video. The main tricks given in the video...