m8more's channel

I spent about $150 on tools. These tools can be used for any bearings I may need to do in the future. I bought the tools at Harbor Freight.

I spent about $150 on tools. These tools can be used for any bearings I may need to do in the future. I bought the tools at Harbor Freight.

Well as I said in the video I shot this some time ago but never posted it. I've been snowed in for a couple of days so I haven't been to the shop ...

If your a do-it-yourselfer and you've been told you need a front wheel bearing, you can do it. There are different types of wheel bearings. This...

Testing a starter means finding out how healthy it is, or how many amp it is drawing. You can use a multimeter to test how many volts the starte...

Intermediate Axle Support Bearing Squeak

How To Use A Multimeter

Link to full video

http://www.ericthecarguy.co...

This video covers the step by step that I went through to replace a clutch on a 2002 F...

THIS IS A SHORT VIDEO TO HELP SHOW HOW TO REPLACE THE CONTROL ARM BUSHINGS ON A 1989 DODGE CARAVAN. FOR MORE INFORMATION ON THESE PRODUCTS VISIT W...

Scanners are great tools, but sometimes they aren't any help. That's when understanding the system, and how to test it is all you have. Here are...

Sometimes the simplest things are the easiest as well. Here's a cool tip on how to remove the window crank handle on a GM door.

Another video from the library of GREATAUTOHELP.com. This one shows what happens when a fuel pressure regulator fails on 3.1 and 3.4 v6 GM engines.

Detailing common failures in 2g DSM shifters, repairing a stock shifter, the B&M Short Shifter, the Symborski Shifter Bushing set, bronze shifter l...

EXPAND THE INFO SECTION. I made a video about changing gear oil in a manual transaxle. People were grateful for it, but the AWD guys wanted a vid...

Installing an AWD transmission, transfer case, axles, mounts, crossmember and sensors. Torque specs and part numbers are listed for a '95 AWD, but...

I'm bench-bleeding a clutch slave cylinder and installing it on the car, then bleeding the rest of the hydraulics. This video covers 2 processes. ...

This video details the things you should inspect when you have the transmission out. All part numbers listed in the video are for a '95 AWD unless...

http://toolsandtime.com/

here is a quick over view on how i perform a safety inspection i don't cover everything in this video however i go over so...

Door ajar switches can be confusing, especially when some of them work the opposite of others. Here's how to isolate them.

Sometimes an alternator may be intermittantly bad. We finally caught this one when it was dropping out.

This style rear brakes is a little different and can be difficult. There is a tool available that makes it much easier. This video will show yo...

Sometimes when you remove a head it's easy to see that the valves are leaking. And, sometimes it's hard to tell. But you don't want to risk putti...

Scanners are great tools, but sometimes they aren't any help. That's when understanding the system, and how to test it is all you have. Here are...

Scanners are great tools, but sometimes they aren't any help. That's when understanding the system, and how to test it is all you have. Here are...

This is a small segment from my advanced engine performance class. The focus is how to use a vacuum gauge to test an engine.

This video shows the process for adjusting the clutch on a naturally aspirated (non-turbo) Dodge Stealth or Mitsubishi 3000GT. The clearance is der...

Episode #4 got 13,000 LIKES!!! Can We beat that?

http://www.whiteboy7thst.sp...

NEW T-SHIRTS!!!

SUBSCRIBE so you don't miss any of the ...

Lets get 20,000 GOATS to Rate this video! That would be crazy!

Watch Ep. 1 here! http://www.youtube.com/watc...

17% off shirts w/ code...

I purchased a cheap air compressor from Harbor Freight (94667). This air compressor was purchased for the air tank to connect to a better quality a...

Use multimeter to measure resistance and voltage

Due to it's unique reverse-flow cooling system, some people can be intimidated when it comes to proper cooling system maintenance on GM 5.7L LT1 an...

Wire Insulation Remover aka Cheap Stripper

The guys at GREATAUTOHELP.com show you a trick to fix a bad fuel injector on a 3.1l / 3.4l chevy, buick, pontiac, olds engine if you suspect it is ...

If you've ever wondered what a relay is and how it works, this is the video you've been hoping for... Other information about the FET book is at ht...

WATCH BLOOPERS & MORE: http://bit.ly/ZELDAxtras

DOWNLOAD THE SONG: http://bit.ly/ZELDArap

DOWNLOAD UNCENSORED SONG: http://bit.ly/ZELDArapX

GET TH...

you guys are crazy, i think this is funny. lol

Written by me 
Timothy DeLaGhetto

http://twitter.com/traphik

http://www.youtube.com/timo......

aka Cell Death. Apoptosis is a process where a cell is degraded in order for it to be ultimately engulfed and recycled. Apoptosis can occur when ...

If tree sap hardens on the surface of a car, carefully use a razor blade to chip away at the stain without penetrating the paint. Apply polish to r...

Tweet! http://bit.ly/RTWhoseGun Facebook! http://on.fb.me/nQoOQ5

Clinton Jones, aka http://youtube.com/pwnisher and I engage in some hand-to-hand ...

Playing Dead Ep. 10: http://www.youtube.com/watc...

The Art of Playing Dead Ep. 11

Clip by:

http://youtube.com/rockyroa...

My Twitt...

Airborne Acrobatics: http://www.youtube.com/watc...

Milk the Cow

Clip by:

http://youtube.com/GettinClips

My Twitter:

http://twitter....

Bench press training,IPF bar,230kg(507lb) 3 reps raw

127kg BW

If your a do-it- yourselfer and you want to save some money by changing your own front brakes on a Ford Escape, here's how to do it.

General procedure to remove and reinstall a/c compressor clutches. For compressor tools and parts visit our website at www.centuryautoair.com.