justforyou618's channel

I'm glad your winter has been mild. Ours has too. It's 87°F here right now!

Have you ever had to get more than 1 load to go through the winter? Just a thought, you could put some porthole glass in at various heights so you wouldn't have to do the ladder!

Hi!

Long time no see! That's the way you clean the boiler tubes on old steam locomotives. If you look at a photo of one, the whole front cap comes off. I enjoy watching your videos on this heating system! I think it is an excellent idea especially where you live. I'd trade a little labor for the ...

Awesome!!!

That cart hauls butt! Looks like tons'o' fun!

Cool Dude!

I love blowing stuff up too! Keep it safe!!! :)

Personally I like fuel injection, but instead of the "E" prefix it should say Hilborn! :)

Those are always a favorite target for me also! Good idea of the sheet to catch all the pieces. Makes cleanup much easier! 00 buck does a good job as well! Watermelons are definitely cool,but they're getting to be expensive! Keep up the good work,I always enjoy yours and your sons videos!!!

So I'm not the only one who forgets to put the tubing on!!! Yep,soldering is the only way to do automotive and marine wiring. The solder actually makes a weather proof joint as well as a good mechanical joint,and most importantly,the very best electrical joint possible! I know in a boat,you're wa...

Always loved "The Pretenders"!

That was easy! I just can't figure out why the smaller pipe isn't froze too? I have a friend in New Hampshire,that puts a kind of electrical cord though his pipe. It gets warm enough to keep it from freezing up! Your idea is better,cause it doesn't need electricity to work!

Glad you're OK! Looks like it's time to mount all those fragile ignition parts a little more inboard out of harms way! Good Luck on it,I've flipped a few buggies back in my time too!!!

That was awesome! I've done plenty of that in sand,but snow looks like fun too! That hill you were going over,is that all snow? I've never seen snow that deep!

Looks like the outside birds got lost on the way down South! Inside birds have it made! I had no idea birds would eat oranges! They don't here,and we've got LOTS of oranges!

@groutaone,the heat exchanger is just like yours! saltwater flows around the tubes,and engine coolant flows through the tubes. This keeps your engine from rusting away. Boats that use direct water cooling are usually used in lakes and rivers,where it's mostly fresh water. An engine driven pump pu...

You're awesome! I hope you enjoy your stay there! It is a beautiful part of the world,and you fit it perfectly! :)

That object's shape and size is similar to one of the "Gulf Breeze Fla." sightings in the late 80s. I definitely think there are other intelligent beings in the universe. In a lot of sightings,people have reported hearing nothing,when observing these craft flying. I remember back in the 60s,when ...

Closer than I ever want to be!!!

Hi! I'm from the U.S. so I get to watch Ellen quite often. I think her show is wonderful. I saw the episode with Graeme Taylor and I have nothing but admiration for him! He went to another town to defend his teacher at a school board hearing. I haven't heard anything of the outcome,but I hope the...

Cool video!!! Down here in the sunshine state,we overseed the greens and tees on the golf courses with rye for the winter. Keeps it nice and pretty for you guys,when your down to beat the ball a little bit!

You must outgrow your clothes pretty quick! You're bigger with every video! :)

That's too nice a truck to go to waste sitting! You can't beat a 454! almost bullet proof if you keep the rpms reasonable. I noticed an automatic column and a clutch pedal. Guessing it was a granny 4spd once!

I'd have to have changed my pants after that!

Cool video! It'd be handy to have the terminator destructor vision!!! :)

EXCELLENT! Good video!!!

Turkeys can see and hear pretty well! Iv'e tried sneaking up on them and about 30 yds was as close as I could get. That's plenty close enough for my .410,though!

Keep all those pins lubed up a little and they'll come right apart. Iv'e had to work on those where they were totally rusted in place. That's a nice machine you have there! times right around the corner for the snow plow! :)