jdchmiel's channel

This video is for the Challenge that Waldhandwerk (sepp) is having hope you enjoy

I recently bought a Grizzly 4003G lathe, which has proven to be a very useful tool in my shop and a major upgrade from my previous lathe. The 4003...

this is how a subwoofer enclosure is built, it is ported and is tuned to 35hz the subwoofers that i am installing are 2 re 8's that are dual voice ...

The story thus far: Will Smith is chasing Trinity after she tries an escape with the secret documents. Sean Connery is not far behind and Nicolas C...

Please watch also, THE SUPER-EFFICIENT ENGINE ( Part 3).

Watch as the 638-horse power Corvette ZR1 equipped with Michelin Pilot Sport Cup Tires laps the Virginia International Raceway "Grand Course" in ...

From the Jan./Feb. 2003 article in The Home Shop Machinist magazine.

www.homeshopmachinist.net

The similarities and differences if the toyota 200mm and 212mm C series setups for first gen MR2's. Also comparison to the 2zz C series setup, pres...

Piston comparisons. Also measured EJ20 but did not do it on video

ringland heights

4.2mm EJ25 non turbo 165hp 2.5 litter 10:1 subaru motor

4.5mm EJ...

Subaru Impreza / Forester EJ25 flywheel, clutch, pressure plate comparison to a Honda Accord F23a. Toyota vs Honda flywheel bolts. Clutchnet disc...

1GRFE, toyota, tacoma v6 flexplate compared to 1mzfe / 3mzfe 3vz etc front wheel drive V6. Fidanza lightweight aluminum flywheel, why a 1grfe will...

fidanza lightweight flywheel for toyota V6's including 1mzfe, 3mzfe, 2grfe but NOT the 1grfse or 2grfse. comparing v6 flywheel to 4ag, 4agze, 2zz ...

The similarities and differences between the 4agze clutch / flywheel / disc and the 4ag. Some reference to thge 3sgte and fwd toyota v6 setups as w...

A comparison of the early 200mm first gen 4age MR2 clutch and flywheel with the later 212mm clutch and flywheel, as well as the 4agze flywheel and ...

Song by Mackthese performing My Body. (C) 2010 Maxi Records.

Replacement of lost materials due to wear from bearing failure and packing abuse...

Choir Of Young Believers / Things I Stole // Secret Love Vol.5 /// 2008

Off-center hole boring on a lathe

Here's a modofocation that you don't see every day, John Edwards @ Costa Mesa R&D Automotive Machine is drilling a new bolt pattern for a modern cl...

One Saturday I wanted to use a 0.5mm drill bit in my lathe to cut a heater barrel.

Blog: http://www.keegan.org/repra...

This is one way to cut an internal keyway with a lathe. This is a good option if you need to make an internal keyway but do not have a broach set....

This is a tip for squaring up your vise fairly accurately without spending time using a test indicator each time. At the time I shot the video, I ...

Homemade surface grinder

so easy you can do it. please subscribe.

Decided to make this cutter up using a standard lathe tool. Was an interesting experience and I was surprised at how well it actually works. It wil...

The lathe with 5/8" endmill plowing through some 1" 2011 aluminum in vice held in compound to make some D shaped washers. Lathe is Southbend from ...

This is NOT what you want

Screw Jack continued. Milled some flats on the jack barrel for a wrench.

Got so focused on making sure the camera was going to have awhile before the battery went dead, I forgot an important part of the thread turning pr...

I think a new back plate for the three jaw chuck is inevitable; and the key is worn and could be replaced. I'm thinking of trying my hand at making...

This could have been catastrophic!

Download the music on iTunes: http://bit.ly/vRivnX

or Bandcamp: http://bit.ly/vZDji5

Face: http://fb.com/CorridorDigital Tweet: @CorridorDigital

...

http://www.weldingtipsandtr...

mig welding tips and techniques for welding one inch thick steel plates to square...

A satirical short film taking a look at the national debt and how it applies to just one family. Watch the guy from the Ferris Bueller Superbowl Sp...

A free audio copy of the mashup is available on Facebook:

http://www.facebook.com/ith...

11 video live APC40 mashup by Chris from Ithaca Audi...

I made this. Like it? I have better quality and more recent stuff over here: http://soundcloud.com/dave-...

Be sure to check the descriptions ...