gregoryscottsr's channel

The refurbishment of the Wood chop saw, seen in Neglect...

few clips of the general hard at work on its first job

The Torchmate 2 CNC plasma cutting table can be purchased as a gantry kit or bolt together table allowing for big savings and yet still providing r...

http://www.weldingtipsandtr...

Jackson NexGen auto darkening welding helmet vs Cheap Auto Darkening helmet wi...

Grooves added to match original .

all code for this job was hand written no cad software used

Grooves added to match original .

all code for this job was hand written no cad software used

The ecological footprint left by Huntington Industries, one of the most environmentally friendly furniture manufacturers in the industry, is gettin...

Tubalcain shows how to measure male & female dovetails on the Atlas lathe.

worth watching cause I burn the saw up in the end.. Little fire and spark n sh*t.. It just starts losing power and I'm like, 'da hell w/ it' ...

A tear down on a giant wood chop saw

Replacement of lost materials due to wear from bearing failure and packing abuse...

See more at: http://www.wretchedradio.com

Afroman shows you what to look for in a multimeter, and how to use a multimeter to measure voltage, current, resistance and continuity.

Multimeter ...

Http://www.weldingtipsandtrick­s.com/miller-plasma-cutter-par­t2.html

miller plasma cutter - the spectrum 625 Xtreme.

air pressure and air quality a...

http://www.greenpowerscienc...

CUTTING A PERFECT CIRCLE ON A TABLE SAW. MAKE A PARABOLIC MIRROR COPYING A PARABOLOID. MAKE PERFECTL...

http://www.widgetwerks.com

I scored this demo kit off eBay and wanted to share a little about these actuators and how easy they are to setup and u...

This video continues the last video by showing the 270 Watts panels installed on the roof to complete the system.

[ Full info and comments @ http://www.RoboCNC.nl/?p=2922]

[RoboCNC Frees & Graveerwerk http://www.RoboCNC.nl/]

For the POTOM bar I had to make a n...

[ Full info and comments @ http://www.RoboCNC.nl/?p=2942]

[RoboCNC Frees & Graveerwerk http://www.RoboCNC.nl/]

I have made the clublogo for S.V. A...

[ Full info and comments @ http://www.RoboCNC.nl/?p=2942]

[RoboCNC Frees & Graveerwerk http://www.RoboCNC.nl/]

I have made the clublogo for S.V. A...

Using a microwave oven to steam bend small pieces of wood. These are White Ash, 9 and 16 inches long, for a wooden 1880's Melonseed Skiff project. ...

Rapid tests for my homebuilt cnc. Checkout out My website http://www.automatedwoodwor... for information and plans. Also check out my build...

Repair on a 1840's Tower Clock

See more at: http://www.wretchedradio.com

See more at: http://www.wretchedradio.com

JUST A BIT MORE INFO AS TO HOW TO MAKE YOUR OWN. KEEP IN MIND IF YOU HAVN'T FIGURED IT OUT BY WATCHING THE FIRST VIDEO, YOU PROBABLY SHOULDN'T BE U...

http://oggcraft.jp/eng/eng_...

http://oggcraft.jp/eng/eng_...

http://www.weldingtipsandtr...

Tips for tig welding cast aluminum. Aluminum castings are full of impurities and p...

Bob Schmidt shows you an easy and accurate way to get a center mark for cabinet, floor layout & wallpaper starting points where accuracy is importa...

BOB SCHMIDT SHOWS YOU HOW TO CUT A STRAIGHT LINE EVERY TIME WITH AN EASY TO MAKE HOMEMADE JIG FOR YOUR HOME REMODELING PROJECTS.POWER SAWS

Alternate energy using leafs to make burning logs. Leaf log maker, patent pending. turns leaves into log for the fireplace, furnace. green energy s...

http://www.woodcowboyhats.com - Woodturning a Cowboy Hat from a 200 pound log.

Precision Plasma LLC has developed a low cost 6" rotary chuck for CNC Plasma Cutting.

watching a new Deere 843K feller buncher at a logging expo

Creating a replacement axle tube for a 1972 Oshkosh Sander, that took a shit because of the lack of greasing...

Heat shrinking the Axle tube in th...

The RMD™ and Pro-Pulse™ processes found in PipeWorx contribute significantly to Graham Corporation's 20 percent reduction in production hours by im...

48" bar

Way Of The Master - Mormonism Mormons (Part 3)

here is solomons Bilateral cochlear implant activation. first the activate the right ear, then the left and then both together. amazing my son can ...

Or, you know, not.

A mother's quadruplets laugh consistently in sync.

Turning the end of a Crank shaft to support a clutch pulley, modified for a go cart...

Me and my Kearney & Trecker, a long coming requested video!