dkmgm2011's channel

Just how loud is a .17HMR? When it's suppressed it's comparable to an unsurpassed .22LR firing subsonic ammunition. When it isn't, it is comparable...

Dale Doyle pulling Greg Pickards truck out with the Can-AM 800. Very dissapointing Pickard

Texas hog with reverse angle footage (Full Version). Just doing my part.

90 kills in 2 minutes with a hunting bow

Pat Lefemine Jr takes his 3rd hog in australia with a

We captured this on video early October while tracking down a Bobcat in south Mississippi. We tried to track down this creature and was unable to l...

new small game broadhead from g5 take a look squrril smoked him

This video shows myself shooting a bow and arrow at 60 yards at a deer target. The arrows are guided by FOB's and have Slick Trick broadheads for ...

this is an under the arm veiw of an arrow being shot at 5000 frmaes per second

Hardcore Archery - British Columbia - 3D Archery Competition. Hardcore Archery family competition from Okanagan British Columbia.

For More Info: h...

Hunting compilation - Partridge with Bow & Arrow

stulls preserve, brad baker, zack knick, george knick, randall knick, matt boekman, john hancock, filmed by gordy knick

My friend Kahley and I were invited to go "opposum kickin" with these good old boys from Grand Rivers, KY. I had them explain what exactly that en...

winter opossum with a bow. http://www.gearbids.net/

damn black chevy at sand hills by st. helen mi. labor day 2010

Bow Hunting in New Hampshire. This is the first deer of the 2010 deer season. My uncle Randy took this Doe with his Bow. It is a nice 110 lb deer p...

Just a quick video of some bowfishing using the GoPro HD Hero camera to record. I used setting r3 which records 1280x720 @ 60 frames per second. ...

Yamaha Rhino at River Run near Jacksonville, TX (3/5/11) attempts to skirt the edge of the Crazy 8 mud hole. Hole was deeper than he expected, then...

After my buddy built a FN90 replica, I tried my luck at doing a similar one using the body of a Steyr Aug. I will try to answer questions you have.

November 4 2009 Lake County Illinois 4:25pm. Wind SSE 2mph. 41 degrees. Cloudy light rain on & off , Barometer 30.23 falling, Fullmoon 97% of the M...

Tim Wells takes out a squirrel, some birds, some fish, and anything else he can with his trusty bow.

My second mini buggy build using parts off first build. Built from scratch. Runs a CBR600 f4 engine, fox 2.0 air shocks all around, with rear trunk...

My 1997 Polaris XC 600 on the water. After flooding in Michigan, this ditch was approx. 4ft. deep. First time on water.

Unbelievable Snowmobile climb!

Read the build up...Awesome team

www.shockdrifting.com

bossted to 18PSI

A group of gator hunters show off a more than 13-foot-long alligator they caught over the weekend in South Carolina

Don Dolph bowfishing on Lake Erie on 6.10.09. Looking like an alien spacecraft approaching out of the night, Don Dolph's 25-foot TriToon pontoon bo...

Note: Carp are a feral and invasive species in our area. They cause a lot of harm to fish such as trout, bass, walleye, etc. as well as the environ...

Tim Farmer tries his hand at bowfishing on the Tennessee River below Barkley Dam. His aim is for the invasive bighead carp.

Here's a short teaser about an upcoming video I'm working on: Squirrel hunting with a primitive bow. I'm still compiling footage, and as soon as I...

It was like 10 degrees when we started it, thats why theres alot if smoke. My 2010 VR Camaro with longtube headers, x - pipe, and SLP Loudmouth 1.

I've had a ton of emails asking for more shots of the build and video of it running down the street. Here a short clip to give you some idea of wha...

Started the Vespa 400 outside today....

You can see it is basically wired now. Dash is installed, Harley Sportster engine buttoned up, lights fron...

V-Twin Panhead

Ignition: Spark

Bore: 1 5/16 in.

Stroke: 1 1/2 in.

Two Cylinder Four Cycle

No Castings Used

This engine was scratch built to a sca...

Just completed ... mostly machined on a Tormach PCNC mill with SolidWorks/SprutCam CAD/CAM plus manual lathe work on the cast iron cylinders, pisto...