dbjornn's channel
Loading...
-
dbjornn
added to a playlist
2 months ago
Ross Nanotechnology's NeverWet superhydrophobic spray-on coating
+++SPECIAL NOTICE+++NeverWet products will be available to consumers in early 2012. Register at www.neverwet.com for first notice.+++
Ross Technolo...
-
Handheld Hotwire Foam Cutter Review
-
Foam Cutting: Hot Wire Bow Cutter
It's Big. It's Bad. It will knock your block off! Cuts EPS foam fast, wide, deep or both - configure it 2 or 4 feet long by 6 or 18 inches deep. Ch...
-
Home Made Foam Cutter
This is a home made foam cutter I am using to shave down foam to a proper height to fit between aircraft bulkheads.
-
Home made Foam Cutter
A hot wire foam cutter made from a #10 guitar string, a 24V/2A transformer, and a dimmer switch. A compression spring held by washers on a screw k...
-
DIY Hot-Wire Power Supply (Vid 1 of 2)
This is video 1 of 2 in my short series showing you how to build your own inexpensive, reliable, and safe power supply for heating the hot-wire for...
-
simple homemade hot wire foam cutter
this was very easy to make. anyone can do it if their at least a little bit smart. if you have any questions, concerns, or comments about this or a...
-
Cutting Foam Wings with a Hot Wire Powered by a Battery Charger
Cutting symetrical wings for a delta flyer from 1" foamular 150 (pink foam) with a hot wire. Hot wire is powered by a 2 amp 12volt battery charger...
-
-
dbjornn
added to a playlist
2 months ago
Powerful Homemade Burning Laser Built From Computer Parts
Here is a burning laser that I built nearly entirely from old computer parts, power is around 250mW. The power supply, multiple heatsinks, and lase...
-
Weekend Project: Cosmic Night Light
Make a glittering LED constelation jammed in resin! This is Part 1 of this two part project.
-
home made hot wire cutter
Just a little bit showing my home made hot wire cutter and how I use it to cut out depron foam rc plane parts. more info at http://www.1bad69.com/r...
-
Weekend Project: Make a Vacuum Former
Here's a cheap and easy way to make 3D plastic forms like Stormtrooper costumes and tons of other things. Cost: around $20.
-
Weekend Project: How to Make Char Cloth
Learn how to make a cheap and effective fire starter made from an old t-shirt.
-
Weekend Project: The Powerfake
Take an old outdated PS/2 or USB ball mouse and turn it into a handy multimedia controller.
-
Amazing Lasers! - Blu-ray Laser Phaser!
Hack a Playstation 3 blu-ray laser and turn the Star Trek Phaser into a Blu-Ray Laser Phaser!
CAUTION!! Lasers can be dangerous! Do not point them...
-
Weekend Project: Telekinetic Pen
Watch as an ordinary Sharpie Pen comes alive! You can make it move with your mind...or can you?
-
-
dbjornn
added to a playlist
2 months ago
Cutting Foam with a Electric Kitchen Knife
clean, smooth cuts. no tearing.
-
EZE Foam Cutter
Like a hot knife through butter! www.chicktool.com
-
Weekend Project: Micro Forge
Do some blacksmithing and make your own nails and other small iron parts.
Get the PDF for this project: http://blog.makezine.com/ar......
-
Quick-Draw Gadget!
I'll show you how to make the Colgate Wisp Quick Draw Gadget.
Check out my 'secret' classic videos: http://www.kipkay.com/classics
Laser Videos: ...
-
Weekend Project: New Life For Old Zip Drives
The good old Zip Drive introduced by Iomega in late 1994 served it's purpose as a medium-capacity removable disk storage system until obsolescence ...
-
How to Chill A Coke In just a second!!
We are now showing you a secret " How to Chill A Coke In just a second! ". LOOK AT WHAT I'VE DONE TO THE BOTTLE OF COCA COLA. Thanks for all the vi...
-
About dbjornn's channel