acklan3's channel

Tubalcain discusses different types of screw threads. Part 1 of a 2 part video.

Tubalcain shows how to cut & thread pipe. Old technology--but still useful to some.

Tubalcain talks about dies & threading. This is part 3 of a 3 part series. Threading on the lathe is discussed.

Tubalcain talks about dies & threading. This is part 2 of a 3 part series. Threading by hand in the vise is demonstrated.

Tubalcain talks about dies & threading. This is part 1 of a 3 part series.

Tubalcain shows how to tap metal on the lathe & drill press

This emergency rescue helicopter almost became the emergency itself. The BK 117 was about to land to pick up a victim in Phoenix (USA) when it sudd...

Part 1 of 3. Tubalcain shows how to machine a brass bearing on the Clausing lathe.

Created using the Stupeflix Youtube App

MACHINE SHOP TIPS #70 Atlas Lathe Milling Attachment Part 3 of 3 tubalcain

A two part series on holding the work in the Bridgeport mill.

Tubalcain discusses various makes of metal lathes and gives tips on what to watch for when buying a used lathe.

Part 2 of 3

An introduction to the different types of reamers and their purpose.

Reamers are used to size a predrilled hole. They produce a very accurately si...

Sample bits of the TOOLS for MEASUREMENT chapter in Machine Shop Secrets - a 21/2 hr. program designed to give you an overall look into manufacturi...

Music video by Toby Keith performing Red Solo Cup. (C) 2011 Show Dog -- Universal Music, LLC

3 old electric writting machine for axes, motors and other mecanical stuff. Some wood, screws and low price part. 2 PCF8754 for I2C communication a...

Making a tool rest for a bench grinder on my 1942 bridgeport milling machine

This is a video showing one of our units actully producing power and is narrated by the customer who owns it.

Pat Downey has been working with Micro-hydro systems for the last forty years. He has installed his systems all over Africa, from Malawi to Congo ...

A demonstration on harnessing the power of water to make relatively free electricity .672 Kwh a day in this case. Check out: http://www.allenergies...

In the island of Saint Maarten inhabited by the DUTCH where you can see planes so close that you can touch them! Or die in the way! Lol

My father made this so we could lift sheets of plywood to be fastend to the ceiling 14 feet off the ground with little effort. This was made out of...

I built this crane out of lumberyard wood and two 2500 lb. rated ATV winches to help me build a retaining wall for my barn. It has remotes and work...

We have developed and prototyped a new and significantly improved mobile hoist for use in lifting, transporting and unloading objects, whether heav...

moving a 2,200 lb mill 150 miles and into a basement!

Lifting heavy logs into trailer using a winch.

One lap around Texas Motorsports Ranch with the Camaro. Wet conditions, so the car is not being pushed very high in the rpms.

This product can be found at:

http://www.excitron.com/web...

3 inch Rotary Chuck driven by Excitron Stepper Motor and Contro...

Flare stack replacement in three days. 160' tall old flare stack was cut into pieces and taken down and replaced with new one.

A short description of my home made cnc's X axis. What I did, and how i did it. http://www.millwork3d.com

Feel free to comment or ask questions.

...

Working Area 235x165x45cm (92x65x18 inch)

control:

Motherboard Csmio-lpt

Mitsubishi PLC FX3G

M880 Stepper drivers

engines:

12.5Nm on each axis

...

My new rotary attachment is finally ready after a couple of weeks in the making (I didn't spend too much time building it though)

It's a Vexta 5 ph...

** Please read the comments if you have any questions as there are a lot of answers in them to most of the common question asked ** Don't forget t...

Работа механики

I proudly want to present you my plasma router.

It´s not yet completely finished.

The router is belt driven by stepper motors.

The controller is ...

small diy adjustable turret on cross slide

Grinding rest attachment to allow you to hold correct relief angles on lathe tools while sharpening. I doubt that this is an original idea but I ha...

49" x 40' Used Niles Heavy Duty Engine Lathe, Mdl. Heavy Duty, 48" 4 Jaw Chuck, 40 3/4" Over Carriage, (2) Roller Type Steady Rest, Tool Post, Rapi...

After my attempts to train pygmy marmosets to use miniature sandblasters inside motorcycle tanks failed miserably (boy, can those little buggers bi...

Watch..New Improved Q5-2000 http://www.youtube.com/watc...

Instead of paying hundreds of dollars for a name brand vibratory cleaner, I...

A two part series on holding the work in the Bridgeport mill.

Tis video is a demonstration of the disc lock holding power of the new Super Duty 4th axis prototype. Shaving across the top of a round bar without...

Tubalcain explains backlash between screws & nuts as applied to the atlas lathe crossfeed.

A primer on MORSE TAPERS.

Morse Taper

How to dress/clean up/flatten a bench grinding wheel

This is a short video showing a refleftice sensor and a panel meter set up to operate as a tachometer system. The tachometer can be set up to trigg...