MrSpad007's channel

part three of fiddling with a wades

Ask and you shall receive. A viewer asked us to show the differences between the older SEED HG kits and the new remasters and we show you just that...

my attempt's at explaining hacking my reprap prusa,

not following the rules and what not might be some tips and tricks in there

Replacing the flaky BLDC motor and flaky electronics on my Mikini 1610L with an AC inverter duty motor and Hitachi VFD

part two of my tut for a wades' extruder/tractor drive.

The Music Publishing Rights Collecting Society is a scam group. They are trying to make money off of other people's work or material from the publi...

Model Refs from the star wars exhibit in Santa Ana California until 4/18/2012. 5' Falcon, Star Destroyer, Y-Wing, Landspeeder, Walker and 4' X-Wing.

This series forms the basis of a "How-Not-To" Build DVD set.

In this Flight Log, we are in the last stages of putting it all together for lighting!

This series forms the basis of a "How-Not-To" Build DVD set.

In this Flight Log, we are in the last stages of putting it all together for lighting!

For years, whent here was a quick paint fix needed on a pairt, I would loosely dunk the airbrush siphon into a jar of paint, holding it precariousl...

Frank Davies's Sarrus Linear Axis see more at http://blog.makerbot.com/20... and http://txrxlabs.org

Low profile platform using triple Sarrus linkage in triangle position. 1:2 wooden scale model to test functionality.

Idea based on inmotionsimulati...

Testing a Phidgets 42BYGH40(M)-160-4A NEMA 17 Bipolar 26:1 Planetary Gearbox Stepper

1:02 retract

1:20 retract

1:45 trying to stop it

Gearotic Motion Tutorial 3.xx

Preforming a dry run, no extrusion of pla plastic at this point.

Made heatsink for hotend on my reprap 3d printer and a few mods.

Casting an aluminum print plate for my Prusa Mendel 3d printer, taking you through the whole process.

12-term Congressman, Air Force Veteran, Doctor, Author, and Presidential Candidate Dr. Ron Paul speak at Colorado State University's Main Ballroom ...

http://www.RonPaul.com - Please like, share, subscribe & comment!

01/06/2012

Ron Paul is America's leading voice for limited, constitutional gove...

This shows how well Synchromesh Cable from SDP/SI works for linear motion instead of the standard T5 or XL belts. Essentially eliminates backlash....

The Basics is a series going over the very basics of miniature painting. Ink and washes are an easy way to shade your models. There are more advanc...

Replacing the flaky BLDC motor and flaky Mikini electronics with an AC motor and hitachi VFD

Marlin firmware 1.0, Slic3r 5.7, Pronterface Windows, Makergear Hybrid Prusa,

Happy New Year, all!

This is a monthly update from the Bench to see where things are going, where they've been and random news bits in between.

...

The site of many a Star Trek shoot, here's a look at it shot on Dec 23, 2011. A faded sign at the front parking boasts a 100yrs of film history at...

This is what you might get with 12 for $20 Chinese eBay linear bearings. They make this horrible clicking noise every few millimeters. Not all di...

I figured I should check my calibration, now that my prints are very clean. I also sped up the printing (fast forward to after the base layer @2:1...

This is an LM8UU linear bearing X end idler that is going on to my Gen2 Prusa. There are three bridge layers:

1) 0:12 (obvious)

2) 2:42 (in the b...

This is towards the beginning of a 47 tooth teardrop gear for a Wade's accessible extruder. Notice the "lap" it takes after completing the base la...

Part 2 of the build.

Inspired and encouraged by comments and feedback on my Mendel Bling build and the wonderful colourful Faberdashery plastic th...

http://www.hlj.com

HobbyLink Japan has just acquired a sample of Tamiya's new P-51D Mustang! Here HLJ president Scott T. Hards takes you through t...

Usually this is a monthly update on where things are going and where they've just been with random news bits in between. This month is special as ...

Print

Testing Slic3r 0.5.5b

Avaliable from Night Works Audio mail@nightworksaudio.com.au www.nightworksaudio.com.au

beginners tutorial part 1 for Freecad.

This is part 2 of my update on improvements I have made to make my 3D printer to make it more reliable and generally work better.