MrNikochannel's channel

ekalla kunnon talvi ajelulla vähän innostuttiin bolaris miehen kanssa sladittelemaan

closeup fire

more fireplace videos http://www.youtube.com/watc......

Huonosti paketoitu.

Ympäristökuormituksen vähentämiseksi viimeisenpäivän elintarvikkeiden ostooikeus alennettuun hintaan kaupan kylmäketjusta olis askel yrityksessä pi...

Kun siinä edellisessä oli katkaisija rikki

A half of a pontiac 6000 does some crazy endo stunts etc.

Orion Music + More - June 23 + 24, 2012 - Atlantic City, NJ - Bader Field

www.orionmusicandmore.com

niilon tapaan

I talked with Joe last week for the first time and asked if he noticed a helicopter flying over his property and if he was OK with it. He said yes...

I want flames!, Loud flames!

I know there is no oil getting to the top end, the oil pump is not happy at all.

Hermoheikoille. kolvaus alkaa 12:35

basic tutorial on how to cook chicken & rice by Jonathan Irizarry.

You CANNOT get big without eating!

Jonathan's Youtube: http://www.youtube.c...

Tweet! http://bit.ly/RTNWredux FB! http://on.fb.me/AelBXe

Brandon, Clint, and I try our hand at American Ninja Warrior once again, and once again ...

ettäs tiedätte

Tässä Aleksi näyttää mallia

keychain 808 #16 kameran ensitestejä

Testataan nyt kaikki kerralla ja nautiskellaan CRT-monitorin lämmöstä ja sen syöpää aiheuttavasta säteilystä, kylmän talvipäivän lämmittämiseksi te...

Moottoripyörä ohittaa kovaa ylinopeutta siviilipoliisi auton ja huomaa tämän EHKÄ hiukan myöhään... :D

Scalextric Micro Mr1

Scalextric Micro Mania

Mittakaava 1:64

13mm pikaIstukan vaihto

Kreysler & Associates explains how they don't write toolpaths with any other software than PowerMILL for their custom fabrication shop specializing...

APPLY NOW: http://secotools.iapplicant...

With almost 5,000 employees worldwide and presence in more than 45 countries, Seco Tools can offer you...

Axiabore® Fine Boring Heads

Fine boring heads with axially fitted tools Ø 0,3 - 108 mm (inches: 0.12 to 4.25)

I get a lot of questions about the sand I use. Here is my first attempt at making my own greensand. The results are very good. It was a lot of work...

Tubalcain shows how to mill a female dovetail. Project---A thread cutting stop for the 9" South bend lathe. Part 2 of 2

Multahan puuttuu kaikenlaista osaa

The first of 23 videos showing how I make aluminium castings in my home made foundry.

Part one shows how the mould is made and in part two the met...

Kompuroitiin pimeessä kuukausi.

Pokolm Frästechnik GmbH & Co. KG

Adam-Opel-Str. 5

D-33428 Harsewinkel

Deutschland

Telefon: +49 5247 9361-0

Telefax: +49 5247 9361-99

freecall Fax ...

i believe it was spinning and the camera could not process the amount of changing information it was reading.went about 250 feet high.

Ravintola Hullun Poron makuraadissa

Olen nyt kohdannut punaviinin josta olen aina unelmoinut se sopii vaikkapa näin pihvien ja nuudelien kanssa nautittavaksi.

Väriltään oikeanpunaviin...

Bara s Albou. Duvod, proc jeden pes nikdy nestaci:o)

Spiral Bevel Gears MILLED to an AGMA 12 or better! Only by Depo

View the Command 100 product page - http://www.johnhartinternat...

The Command 100 briquetter draws on over sixty y...

The Mazak Hyper Quadrex Series solves the dilemma of how to produce high-complexity parts in medium to low lot sizes and make a nice profit.

The...

A look at the hardest-working parts in a large industrial gas turbine engine, and how they compare to their counterparts in the large aircraft jet ...

Customer is a large "Job Shop" that is experienced with all types of machining operations and many exotic materials. The customer was looking for w...

Star Transaxle main housing - machined from billet aluminium on Mori Seiki NMV5000

Freesdemo MTE tijdens Metav 2012 op BF-3200 met het materiaal 1.4523

Large 5-axis Control Machining Center NMB36100