Kalkaekie's channel

Mike Rodenbaugh's Tube Depot Video - Circuitrix

Long pond at Howard Dills farm "The Cradle of Hockey"

How to build a (new) old antique gas engine cart, hit and miss or throttle governor, it's level, tighten 'er up, sparks,SPARKS! get back dog! get b...

We're finally done. Thanks a million to all who graciously supported me along the way. It was very much appreciated. Regards, John

The very beginning of the cabinet restoration...and a few other things thrown in just for the heck of it.

how holes were made in the old days before oxy acetylene and plasma cutters

#4 How to build a antique type cart for a vintage gas engine, she said, Aaa,,, hippie, you aint left nothing out, even your el cheapo c-clamp is pl...

#3 How to build a cart for a antique gas engine, hit and miss or throttle governor, battery and coil, call them what you like, trolley, cart, wagon...

Part 7 of the tubes series. Learn where the parts are on a tube amp. Learn some of the differences between transistor and tube amps. Learn about ...

Part 2 of the series on Tubes. Learn about tube schematic diagrams, the different types of tubes such as diode, triode, and regulator. See the in...

Amp Controls is a free video lesson by Jody Worrell that will cover how to get different tones out of your guitar amp. Jody will show you the diffe...

#2 How to build a cart for a antique gas engine,, hit and miss with low tension magneto, throttle governor or battery and coil, you are going to ne...

New arrivals like the chassis for the new el84/6v6 switchable amp, got a new hat, wired the board.

A little nighttime fun with the ole Hammarlund.

I've recapped the set and here are the initial results. If you like to learn more about a 'dim bulb tester', check out the old64goat's channel. H...

Measuring chassis voltages. WARNING: SOME CHASSIS VOLTAGES EXCEED 300-VOLTS. THEY'RE VERY DANGEROUS. NEVER TAKE ANY VOLTAGE READING IF YOU DON'T ...

The voltage readings continue.

torsionator

Captured on film, a magical moment: the birth of a guitar amp. We're at 65amps in LA witnessing an amp's first voltage test, and although it might ...

Jeremy Johnson on guitar/vocals. Accompanied by Tom Atkinson on guitar & Rusty Zorns on bass. Bill's Pickin' Parlor, West Columbia, SC, 9-19-08.

I tried:P

Basic Blacksmithing Hot Punching Steel

welding metalwork and forge updates

This is a very basic tutorial on crossovers. I'm no expert but I hope this video answeres a few questions out there. Enjoy!

http://www.djtutor.co...

Sorry about the terrible quality - I don't own a video camera, but this contest was announced the day I finished this amp so I had to give it a sho...

http://www.planetz.com/?p=261 .

In this video, I disassemble a couple different pots (Bourns and CTS 500k audio taper) to show how they're constru...

driving along and we see a Barred Owl sitting in the middle of the road, so we catch it and take it to the vet! there will be an update as soon as ...

We've been snowed in for a few days and the novelty of sledging has worn a little thin so it's time to sing some songs! Here's our Charis with her ...

One of the first songs i ever played in church. I love the catchy beat and lyrics to this song.

Find the lyrics here:

http://www.lyricstime.com/v...

An easy way to enable your AM broadcast band receiver to receive single side-band transmissions.

This video is a re-upload. The first few minutes of the original upload were changed. The rest of the video remains the same.

plow smashed and was driven under the jeep causing a big problem

Just a day in the life of a job shop machinist, she said, let's get this show on the road, this old 1937 maytag multi-motor needs to be rollin', ho...

It all started when the duck tape girl asked, aa, hippie, what you gonna haul that thing a ma jig on?, just her pet name for these old worn out, mo...

How the sliding tooth works, the whole story, brilliant, just brilliant, who invented that little thing a ma jig?, remember that you can't get to m...

This video is a re-upload. It covers the second half of the radio's alignment procedure, adjusting the oscillator, antenna & RF trimmer capacitors.