Grescht's channel

Lyrics:

Here i go

I'll dive right in

Break through the waves

Straight to the ocean floor

And allthough my hands are shaking

I lie perfectly still...

MP3 download: http://www.ronaldjenkees.co...

Or get it from iTunes: http://tinyurl.com/25pkerr

This is another one in the very early stag...

This video was uploaded from an Android phone.

vtac with turboz

http://www.facebook.com/mac...

http://www.twitter.com/macl...

Buy this song on iTunes: http://itunes.apple.com/us/......

This is the first part of a two part series about balance shaft elimination on 4g series engines. This video details the bearings, the other video...

Faster than lighter.... You folks at Youtube can figure it out... Thanks for watching and make sure to post that comment... bigtomscience

Like the inherent double-standard in all stereotypes, it's only appropriate to bash them if you are one, or own one. This is just another example ...

This is a short clip of the most expensive car in the world at the 60th anniversary of Concours d'Elegance. A Bugatti 57S Atlantic originally purc...

Two of my buds from the area are out racing again... Since my car broke on my first pass, I went ahead and put myself to good use. Just some runs ...

Since Henry Ford made the automobile a mass-consumption commodity, people have been finding ways to strip superfluous parts, modify their engines a...

For those of you that read video info... I made YouTube Partnership 2 weeks ago. It's taken almost 3 years an over 4000 hours of work, but I made...

How to replace wheel bearings and seals.

More importantly, this is how to make turbo DSM axles fit in a Dodge Colt, Mitsubishi Mirage, Hyundai E...

There are several ways to press hubs in and out of bearings. A bearing press and bearing splitter is by far the best means of accomplishing this, ...

I think not.

But sometimes they will frag themselves. You haven't owned a DSM for very long if it hasn't happened to you yet. My belts kept flyi...

Taking this to the next step. You saw what I did to make the rear fit, and this is what it took to do the front. There will still be another vide...

I've done this video before. Not in HD, but this time I'm leaving you without an audio track to drown out what I'm doing. In previous videos I re...

This video assumes you're aware that various iterations of the 4g series Mitsubishi engines are designated as Sirius I & II.

For detailed informat...

If you're going to rebuild an engine, this video is required material. None of your measurements mean anything if they're not accurate. I illustr...

4g63's are famous for hosing crankshaft thrust bearings. This video illustrates the process of how to check the thrust bearing clearance whether t...

Connecting rods are the crux of the engine. They're responsible for carrying the force of the explosions that occur in the combustion chamber and ...

It's important to know what you've got even before dealing with the machinist. If you want to inspect a crankshaft, this is how you do it. I deta...

In this episode we measure the bores for the crankshaft and calculate the oil clearances based off of information gathered in the previous video. ...

We're close to the end of the 100-level series. In this video I show you how to measure the cylinder bores using 2 different tools. I compare the...

This video covers how easy it is to calculate piston-to-cylinder wall clearance. It's too easy. This is important because too loose of a gap and ...

There's a reason why there are no subtitled specifications in this video for the block. It's because they don't exist in either service manual, 1g...

Young Meezy Ft Tony Graham - Good, Bad, Ugly

@MrStillSmokin & @itstonygraham

Yelawolf feat. Kid Rock - Let's Roll (Radioactive)

Album: http://www.amazon.de/Radioa......

Download on iTunes: http://goo.gl/gcVR7

THREE T-Shirt designs!: http://goo.gl/jr4sY

So many things to throw on the ground! Featuring Ryan Reynolds...

The black powder cannon I made in shop class. Ballin

Smoke weed everyday, that's all I do.

Use a charles hamilton instrumental - Tae Flow & Method One

Listen and Enjoy - Like or comment

Please don't expect any responses until the end of April as I am currently on a round the world trip.

There is a second version to this bass test,...

I'm up to my ears in madness. Out of space. I've always intended to finish the walls in my garage, but wound up moving in first. There was a gre...

Gresch meisters white pearl.

The sounds in this video are ACTUAL sounds from the Jeep. Everyone began rehearsing their parts 2 weeks before we shot the video. It took us 7 hour...

The price of this turbo will make it a popular purchase, so I figured I'd air out some tech about ways to improve it. This thing is not for everyb...

Happy July 4th! If you have speakers plugged into your computer, turn it up. Hopefully you have a subwoofer, too! This footage is me walking thr...

Last run of the night. I ran one prior to this, but didn't get any footage. Fortunately they lost our timeslip so they gave us a re-match after t...

GSX vs. C5 Corvette. This race didn't prove anything because now we're 1:1. The last time we raced, I broke. I'd have lost that race even if I d...

Why do I know about this?

I'm tired of being the one knowing all the weird crap. If everyone knows it, it won't be weird anymore. It will be com...