250rapid's channel

@piersonmochoa44

Well, I won't said that.....not a nice group for sure but at least he's hitting inside the body on the target silhouette so that means you're dead man... lol

For those "smart a*****" newbies trying to speed up the process, DO NOT use Dremel tool because it will remove the hard nickel plating, or will round off edges that need to be kept sharp and this will results in an even harder pull, non-functioning, or much worse: a totally unsafe pistol with unc...

Hey"zipperhead"!!!...you loaded a magazine with 10 round to kill your self? how many bullets do you need?..isn't one enought?.....what a moron!.. no wonder why you want to blow up you shit for brains.

Not my cup of tea but give the kid some credit because he's just showing a different alternative way to do it plus he clearly said: "Magazine is empty, nothing is in the chamber, wanna be safe in the video" ...He did cleared the gun, so what's the big deal?... His palm in front of the barrel is...

Are the Glock 17 magazines compatible with the G19?

Are the Glock 17 magazines compatible with the G19?

@lskw1 Well, in my case, I'm not a competition shooter like you, I just go to the range twice a month and shoot a couple of hundred rounds each time so, $10 grip goes a loooong way for me and I'm sure it does the same for others, don't need to do all that cutting and triming but again, it might ...

I will skip the Dremel and do it by hand with a Q tip. Many parts have been ruined by using Dremel tool and over-polishing, removing the hard nickel plating, or rounding off edges that need to be kept sharp resulting in an even harder pull, non-functioning, or much worse: a totally unsafe pistol ...

From personal experience,...blue Loctite works great and hold the screws in place, tight, secure and easier to remove, no need for the Red one, it's to strong and you will have "hell" of a time trying to remove the screws unless you use a heat gun but then you'll ruin the grips., it happened to m...

Hey gimador!...does your compensator fits tight to the slide without a gap? I'm asking because I have same compensator installed on my SA1911-A1 (GI) but there's a small gap in between both (comp & slide) and if I push it in with my tumb I can feel movement up and down, not a solid tigh fit.. A...

I'm reviving an old dead video with my question! :) Looks like the compensator doesn't seat flat or tight to the slide, I can see a small gap. Have you tried it out yet? Does the pistol shoot without any problem? Why it doesn't seat flat.

I purchased the black version from BCA Industries but it doesn't seat completely flat or tight to the front of the slide of my Springfield Armory 1911-A1 GI, there is a very small gap between compensator and slide and if I apply pressure to the compensator I can feel it bounce up and down, I'm n...

I purchased the black version from BCA Industries but it doesn't seat completely flat or tight to the front of the slide of my Springfield Armory 1911-A1 GI, there is a small gap between compensator and slide and if I apply pressure to the compensator I can feel it bounce up and down, I'm not su...

I purchased the black version from BCA Industries but it doesn't seat completely flat or tight to the front of the slide of my Springfield Armory 1911-A1 GI, there is a small gap between compensator and slide and if I apply pressure to the compensator I can feel it bounce up and down, I'm not su...

PIECE OF CRAP!!!...Do NOT BUY!! - I learned my lesson after purchasing two of them, one for my 1911 and one for my Beretta 92. They dont stay in place unless you use contact cement. I returned them the next day.

I have the same model pistol (1911-A1 GI) Replaced the hammer with the Wilson combat hammer and only gives me 2 notches when the trigger is pulled back. Is there a reaso why?

Agree with previous review, procedure to "proper fit" should have been covered. It might be a "drop in" in some models but when it comes to a Springfield 1911-A1 GI, this Beavertail is NOT a drop in, needs proper fitting to the frame and the trigger safety in order to make it work properly - Need...

Exactly what I noticed last night!...After I posted here I when back to compare the Wilson beaver tail to the factory one and noticed that the bar that functions the trigger release it's a little to big/long and that's why the safety doesn't move so, you're right,!..that could be the problem. I ...

For those who like these low cost magwells, Kiwi sounds like a good idea to mark the grips because you want to do it right the first time. I will think twice before installing this low cost magwell in a nice pistol and also before grinding a nice set of $70 VZ grips. I say a magwell incorporated...

Just make sure you don't swallow the small piece of straw because then you'll need to put your finger thru your asshole to pull it out.

@jrgnsscmn Helloooo!....We are in the 21st century, remember?... ALL dancing are ridiculous and some worst than others.

Looks nice fro the inside but if you look at it from the outside you will see lots of marks/trails, not a very smooth look.

What about if you don't have a screw?.. or screw driver?.. or a hammer?...Then you're screwed!

Hey dude, it's very difficult to understand what the hell you're talking about but I did understand when you said: "brand new remote"?...well hellooo!... it's a brand new unit, remember??.. plus the DC Car Adapter is NOT a cable to plug in your computer.

I was told is not recommend to keep the slide assembled on the gun when the gun is not in use (or in the safe) in order to avoid keeping the recoil spring under compresion and that's why the kit is shipped with the spring loose and not installed on the slide. It doesn't make any sense to me but ...

I will like to see those bitches face after a shell gets between their tits :>))

Why not use a BUFFING POLISHING WHEEL installed on a bench grinder instead of rubbing and rubbing by hand for 15 minutes a hundred time?...I'm sure the polishing wheel will do the same (or better) job with the same results and in less time. You probably might need some "elbow grease" for those ha...

So, what's the point?....looks like you got to much time in your hands. Get a job or clean your room, cut the grass, give the dog a bath.

Also great to use with the Advantage Arms .22LR Conversion Kit. My 10 years old son finally got a chance to shoot my Glock using the red dot.

@mattn5160

Got mine a week ago, brand new and also I get misfires, one or two out of the 10rnd mag. The firing pin hits the cartridge but no BANG, just "click" - I did a test and and loaded the same cartridge in my Ruger MKIII and it when BANG the first time so, I don't know what's going on wi...

Get rid of the cap since there is no Glocks on the table only Beretta, - Colts 1911 - Cap & Ball Revolvers, etc

He's watching what wheels going round and round??

Otra pregunta !... se puede usar chiltoma roja, amarilla ó solamente tiene que ser chiltoma verde?

Los pantalónes que trae Pototo con la fajita por detras eran los famosos pantalones "Chemises" que usaba mi padre cuando yo apenas tenía 10 años. Se los ponía los Sabados para salir a bailar con mi madre. Ahhh!....que bellos eran aquellos tiempos de mi infancia.

After it's build how do you put the slide on?