Injection Molding 15.5 gr preform 7.3 second cycle time

[dritzz2009]

96 cavity in 7 seconds. Good cycle time but is it your molding parameters optimum?

[crazycarperdaz]

Get a DEMAG, awsome bit of kit!!!

[promerican]

I am not impress...

[InflatablePlane]

Intersting. What is this machine moulding, and out of what kind of polymer?

[sercos72]

It is P.E.T.

[ilmerlo84]

isn't it an Engel press?

[sercos72]

No, it is Netstal.

[borisbevc]

that all is good,but krauss maffei is very simple for optimize,i change tools,and demag or arburg are very good when we need quality on 10,but km is the right choice for level (from 1-10)7

[wwjdtm]

I need a production Manager with PET Preform experience in Ohio

Call John 440-243-5151 ext 230

[promerican]

that cycle time is a joke...you haven't seen the fastest cycle time using a side entry robot. 333 ms..

[BobMarley621945]

Yeah, preform is cold moulded 4g and clamp is black powder explosion closed. What you mentioned as time is the lock to lock - then there is injection, hold and cooling time.

[B0yWithN0Name]

cycle time doesnt mean anything if preform quality factor is absent. what about shrinkage (sink marks) etc?

[BobMarley621945]

You must run Chinese moulds

[kiora2]

I worked on a kraus Maffei PET machine. Had a verticle clamp and it was horrible. I've been to the Husky Plant in Luxemburg and their machines rock.

[patsymtl]

husky s the best

[BobMarley621945]

assume, all you know is Husky? You see, those, that live in caves, do not see the sun.

[casawi80]

but dont forget engel too, of corse arburg is the perfect

[foxacoustics]

All of you trash talking people need to post a video response of your machine doing a better job.

[mumbles4ken]

this puts the machines at my work to shame

[Aotearoald]

Husky rules. No one can beat their HyPET systems and their 2-servo drive robot. This Netstal also has a slow Otto Hofstetter mold. Crappy part transfer (inferior airblow assist) & slow ejection. By the way, what's the preform's wallthickness here? 2.1? or 2.2?

Try running a 4mm WT preform on a OH mold.

And I don't even question if tolerances of the preform's thread are in spec...

[canoetaco]

Husky are garbage, I work with Dline series machines 2 barrel and 4 barrel injection units, and an ENGEL will out perform it day in night out.

[BobMarley621945]

Again - you run Huskys, that's all. People in caves do hardly ever see the sun.

[Aotearoald]

Hey Mister Marley (I thought you were dead) : If Otto Hofstetter only would have optical part detection on their preform transfer. (Husky, MHT and TPS all have them) Hofstetter molds last a lifetime though.

[inancyavas]

injectıon maghıne world one number netstall

[CyberdogD]

Haha Arburg and Kraus Maffei are much better!

Our fast cycle is 6,4 sec!

[wilsonamon]

Well, film it and post it then!

[pelikannakilep]

Arburg and Kraus Maffei don't have PET

Machines! How do you compare???

[baviro01]

When I was in Munich some years ago, I remember there was an KM PET machine.

By the way Netstal is very good.

[vjm78]

Fantastic!!

Congratulations