So go to prison because vandal things, because NOT INTELLIGENT vandal things and because of making bad videos illegaly and built a new one (in the long-long prison), then maaaaaybeeeee you'll get back your freedom!
@lolfunnycp the trick is to smash the top part with the drive facing up so that the metal casing bends up on the opposite end. Then you can pry in a screwdriver and hammer that in until you bend the casing up and the plates are exposed.
It's totally ineffective in destroying data. Hammer can not reach a Curie point. Data may be revealed from reconstructed disk plates with simple methods.
ever heard of data protection? If you're going to dump the harddrive as a company or developer, then you want that data destroyed. formatting does not destroy any data, only complete physical destruction of the harddrive
Man that took a long time. Maybe you should have first opened it up, and then hammered the actual platters? Also, save the magnets, those are very fun.
Dude you need a bigger hammer. It shouldn't take more than one or two shots from a 20 lb. sledge to do the job, and it would be every bit as much fun. THAT is how you dispose of 50 of them in time for those TPS reports.
Nice. Now sit there and do that for 50 of them. Don't forget, you've got 5 TPS reports to file before 2:30, a meeting with the supervisor at 2:45 to discuss those TPS reports, and then you've got to reload the company exchange server before the boss goes home so he can get his email. Have fun!
It takes far less energy to remove the hard drive cover and disassemble the platters. Then just drop them on a sidewalk and use your foot to abrade the surfaces. Not a whole lot of recovery is going to occur after that.
I've spent over 10 years having trouble with this method. It seems that I was trying to hit the hammer with the harddrive instead of the other way around! Thank goodness for this video, now no one will know how foolish I was!
i took off the outer casing though so that i wasn't just beating into the thick metal strip that is meant to protect the disk. then i took off the disks and dented/scratched them with a hammer and a screwdriver. and finally i dislodged a lot of the electronics, ripped half the circuit board out and removed all the serial numbers.
is this enough or do i actually have to smash the inner disks into pieces? they're already very dented and severely scratched.
stupid smasher! I give you an advice, put on your next movie some music with windows movie maker... like for example hard rock or metal. have you aver heard about it? look for example smasher1993 he is a great!!!!
Ok, smashed up HDD with a hammer, that's the first thing anyone would think of - the data on the disk is still able to be recovered by 96% because you didn't even touch the platters
So this is how you divide your hard disk ? parted Magic is easier !
AlaVfx 1 month ago
This has been flagged as spam show
................i just watched this...........
ZeeGooner 3 months ago
why.
miketgreen1 3 months ago
youtube.com/watch?v=fe8SNlhUHjQ - How NOT To Destroy A Hard Drive and How To Grunt & Curse Like An Ape
SpecialAgent08 4 months ago
I hope that was a Samsung HDD
DanieLaixer 6 months ago
1:15 FAIL
dubitativoz 6 months ago
I love the MCT!
Also known as Manual Correction Tool or hammer ^_^
Dragontail1992 6 months ago
So go to prison because vandal things, because NOT INTELLIGENT vandal things and because of making bad videos illegaly and built a new one (in the long-long prison), then maaaaaybeeeee you'll get back your freedom!
DomeArmin 8 months ago
Must of had Windows Vista :P
Giolovescandy 9 months ago
NOOOOOOOOOO D: XD i wish i could do that
elchristopher13 9 months ago
Wouldn't a sledge hammer have done it a lot faster?
Amberle61976 10 months ago
0:05 i thought its a music lol nice jeans btw
ColdVVavezz 1 year ago
these things take forever to destroy! I know from personal experience
godzillalikespie 1 year ago
that hdd is weak... it took me 10 minutes to wreck only half of my hdd with a metal baseball bat. (do not say IM weak cus that will be not original)
Flamable3000 1 year ago
I could still read that HDD for 100% :+
jopitan 1 year ago
its a good way to relase ur anger
wiixbox360mets 1 year ago
i hate that hard drives are so hard to smash because of the metal casing!
lolfunnycp 1 year ago
@lolfunnycp the trick is to smash the top part with the drive facing up so that the metal casing bends up on the opposite end. Then you can pry in a screwdriver and hammer that in until you bend the casing up and the plates are exposed.
batmanpronz 1 year ago
@batmanpronz thanks that makes it a lot easier (especially laptop hard drives)
lolfunnycp 1 year ago
@lolfunnycp are you kidding, thats what makes it so fun
JagermeisterDetox 11 months ago
See if it still works :D
EuroPowa 1 year ago
looks like the original imac G3 harddrive
gab1971 2 years ago
tap tap tap...hit it with your purse...
get a real hammer, like a 38 oz framing hammer or a Binford 2000.
cybersynaptics 2 years ago 6
It's totally ineffective in destroying data. Hammer can not reach a Curie point. Data may be revealed from reconstructed disk plates with simple methods.
duodenit 2 years ago
The strikes on a angle seem to do more damage.
tehballzors 2 years ago
brb, fbi *grabs hammer*
BlacKSacrificE 2 years ago
This would be the coolest screensaver movie, just change the words in the corner to "Optimizing.. Fragmenting Drives"
dynamo9 2 years ago 4
Can I recommend a sledgehammer?
Also, the hard drive stood up surprisingly well at first... then failed spectacularly...
LiamRiordan 2 years ago 2
This comment has received too many negative votes show
why would anyone need to do this to begin with, just fucking format it and reuse it. you're an idiot if you just break it.
david02129 2 years ago
ever heard of data protection? If you're going to dump the harddrive as a company or developer, then you want that data destroyed. formatting does not destroy any data, only complete physical destruction of the harddrive
AlmondMan 2 years ago
You do this to broken drives to destroy the platters so that they cannot be read by a data recovery company.
Petablast 2 years ago
use a bigger hammer, man. sheesh.
3truscan 2 years ago 6
Man that took a long time. Maybe you should have first opened it up, and then hammered the actual platters? Also, save the magnets, those are very fun.
olifantgmail 2 years ago
Dude you need a bigger hammer. It shouldn't take more than one or two shots from a 20 lb. sledge to do the job, and it would be every bit as much fun. THAT is how you dispose of 50 of them in time for those TPS reports.
pyrox23 2 years ago
too... much... pain... must not... look... aaaah
bleyblue 2 years ago
Nice. Now sit there and do that for 50 of them. Don't forget, you've got 5 TPS reports to file before 2:30, a meeting with the supervisor at 2:45 to discuss those TPS reports, and then you've got to reload the company exchange server before the boss goes home so he can get his email. Have fun!
IonOtter 2 years ago
It takes far less energy to remove the hard drive cover and disassemble the platters. Then just drop them on a sidewalk and use your foot to abrade the surfaces. Not a whole lot of recovery is going to occur after that.
voxelman0 2 years ago
Nerd BDSM?
linkdude64 2 years ago
Just because you have a hammer, does every problem look like a hard drive?
reudeeph 2 years ago
Doesn't work very well when you have about 20 - 30 hard drives to do. I could already hear the guy on the video being out of breath.
sniperdoc8404 2 years ago
Just use bigger hammer ;]
xani666 2 years ago
The safety warning on all Estwing hammers says, "Always wear safety gogles when using hand tools. Bystanders should also wear safety goggles."
bokkenka 2 years ago
I've spent over 10 years having trouble with this method. It seems that I was trying to hit the hammer with the harddrive instead of the other way around! Thank goodness for this video, now no one will know how foolish I was!
king0lag 2 years ago 3
Why not use the pointy end? It would probably go faster that way.
DavidTheCatMedia 2 years ago
I wonder how much that HD hates you 0.o
ashthepokemonmaster 2 years ago
i just did it now.
i took off the outer casing though so that i wasn't just beating into the thick metal strip that is meant to protect the disk. then i took off the disks and dented/scratched them with a hammer and a screwdriver. and finally i dislodged a lot of the electronics, ripped half the circuit board out and removed all the serial numbers.
is this enough or do i actually have to smash the inner disks into pieces? they're already very dented and severely scratched.
PhilJamesTaylor 2 years ago
I like how he nudges it back to center.
finderskeepers47 3 years ago 2
Can you do that once more, with feeling?
xaraxen 3 years ago 2
LOL!
icunowlibra 3 years ago
u jsut open it up and and smash the disk then its a empty shell with a reader
twiki2099 4 years ago
A hammmer is not enough, you need to break the inside use a screwdriver, or best yet use a very strong acid.
mike40200 4 years ago
stupid smasher! I give you an advice, put on your next movie some music with windows movie maker... like for example hard rock or metal. have you aver heard about it? look for example smasher1993 he is a great!!!!
silviothebest 4 years ago
@silviothebest thats how i allways make my vids!!!!!! with music!!!!!!! check them out and you wont regret about it!!!!!! ;D
theultimatedestroy80 10 months ago
Ok, smashed up HDD with a hammer, that's the first thing anyone would think of - the data on the disk is still able to be recovered by 96% because you didn't even touch the platters
InfluxUK 4 years ago
Meh it was mostly porn anyway
andrewtatham 4 years ago 2
HAHAHAHAH
curlzboi 4 years ago
get a bigger hammer next time...
juggernaught7 5 years ago
Yeeehhh boi.. Thats what i did.. they are tough sons of bitches
BennyP07 5 years ago
you destructive son of a bitch. fuck you!
FordFusion2006 5 years ago
That was long lol.
hitohori 5 years ago