Rumble activated led mod tutorial

[runescapefreek88]

which side is the positive and negative?

[elementbam23]

@runescapefreek88 pos is towards the middle, im doing the mod right now except not the guide button just an led poking out the side

[pikkuauto20]

what leds did you use? gow many v.?

[richslayerbc08]

can you make it to where the left side lights up when the left motor goes off and same with the right? that would be a cool concept

[darkalyn]

do you need to remove the rumble packs?

[ktmorange08]

When you rumble activate the led, do you need a resistor? I've seen some with resistors and without.

[poopyapple1]

it depends on the volt of the led if you use 3 volt then your fine thats what i usually use and would recomend if your new to this

[SnappingSpider]

nah i dont use them.. waste of money i think.. Altho smart.. But i didnt use one And mines worked for about a year now =D Thicker the wire the less use of a resistor needed =)

[megapyro013]

depends on the voltage of the leds, get like, 2.5-3 volt leds and you shouldnt need one, if you are hookin them up to the batterys power sorce use a little more than 3 volts

[elementbam23]

@ktmorange08 you don't need a resistor as long as the led you chose to use is above 3.0v cause the controller(both batterys put out 1..5vx2 is 3v total)

[wmucker93]

how many led's did u put in the guide button?

[SnappingSpider]

i only did one. just so that my battery last longer and dont die faster =)

[nickman228]

LED lights use almost no power, they wont drain your battery. thats why most appliances use LEDs to indicate they are out of battery

[monkeyfarts9906]

wat size led do u need?

[SnappingSpider]

I dont know the size ass long ass they fit in your guide button i suggest small assorted LED's at Radio Shack just ask them and thell tell you where to go

[butteredmuffins0]

you should use bumper jumper..

[SnappingSpider]

lol i would but i cant get used to it =(

[butteredmuffins0]

it takes like a week to get use to it. its totally worth it in the end tho

[crystalbanana123]

whats this song!! please tell me

[SnappingSpider]

its broken hearts and torn up letters by Lost Prophets :D

[musclecar383]

it seems like the lower right part of the "X" doesnt want to light up.

[SnappingSpider]

sometimes that happens.. you could just put two in there.. i just put one..

[SnappingSpider]

no you just simply connect an led TO the vibrators

[massmurder009]

Ok so let me get this striaght you trade the vibration for leds? And you dont need to connect the leds to a other power source, just to where the tumblers would be?

[SnappingSpider]

i used small assorted leds ask for leds at radioshack they will bring you to them and show you some to pick from......

[corvettezack]

wat kind of leds are they, how strong i need specifics ASAP!!!

[AlmostProSk8rr]

omg dude ty 4 the vid it helped me alot! very good at explaning! keep up the work!

[corvettezack]

can u make a better video please, like step by step lol it will be more easier and less risky for me

[metalcore3546]

check out my guitar videos people

comment

rate

subscribe

[SnappingSpider]

look at the first picture... both wires are soldered to the vibrators

[XboxHell]

yeah what extito said did you solder yours?

[metalcore1324]

cool thanks for the help awsome video

check out my vides people they are guitar videos mainly

[SnappingSpider]

ya np dry water! =D

[XboxHell]

where do you get the leds in canada?

oh yah and where do you solder the wires!!?

[ecTITO]

DID U SOLDER YOURS

[dry0water0stones]

wow ty for the video and for the free led lights you shiped me...