Super Speed Micro-T - 5 (4s lipo! with Quark 33a)

[bigboss5940]

Hi man,

You use the 10000kv losi which is run at max 3S so the motor doesn't burn ?

You use a quark's esc so is the losi's esc will dead in 4S ?

Where did you buy the quark ?

I have found THE brushless for mcro-t :

the turbo ace 91416 (15000kv =) )

But max 2S so in 4S is die ?

Thanks for answer me.

[kargidesign]

@bigboss5940

10250 losi is fine with 3s, but wont last long on 4s.

losi esc is on the edge with 3s, 4s will destroy it.

I bought the quark long time ago...

[bigboss5940]

@kargidesign Thanks for your reply...

So use 4S with losi's motor is just for "test"

Use the turbo ace with 4S is not possible anyway...

The only way is to use losi's solution ; 10250kv and his controller in 3S

What receiver do you use ?

Can the original chassis support the losi's controller, a 3S lipo and a micro receiver ?

The original transmission will resist to this ? or I will need to change it ? only the crown and the gear (in metal) ?

Thanks for all

[sheilstar12]

what motor and speed controller are you running on and were did u get all the blue parts from

plz reply

thanx

[Heirokos]

Is it necessary to shim the differential when switching to brushless or just getting an aluminum gear box?

[kargidesign]

@Heirokos when you get a alu box, without no pressure it shouldn't close fully, but it should close easy when you tighten the screw. Also you may want to burn the gears in without touching wheels to the ground.

[Heirokos]

@kargidesign Oh okay, i will be running a 2s lipo and i don't think it will cause any damage to the diff in the way i drive hehe. Thanks!

[kargidesign]

@Heirokos it may need, because the 3r box that I used was wider inside than the original, causing crown gears not to mesh properly, so it is not about power. But there are tolerances in manufacture ofc, try out without shim first, worst case you go through a set of diffs ;)

[Heirokos]

@kargidesign Yeah lol the only problem i seem to have is the mounting screw for the motor (stock) as it keeps coming out every now and then. I might have to seal off the gap or something so the screw stays intact :/

[kargidesign]

@Heirokos then you probably have too tight gear mesh, no gear backlash OR/AND tight spur. if you still have problems than you can use locktite blue (color code for medium strength), or very tiny drop of CA.

[drakepuma]

nice vid dude..

um can you answer this for me

how much is the micro-t?

and how fast does it go with its original parts?

[cesar11duran]

MPH?

[DaMonsterMonster]

Where'd u get the series adaptors?

[30GB]

what esc are you running? my dt has the stock esc on the xolen... brushless system and im only running 2s but i can make a 3-4s lipo

[plasmaflori]

wow......

[drago433]

how long does the battery last?

lololololololololololololololo­lololol

[limbota]

what is your favorite website to buy mods for your micro-t?

[limbota]

what are those tires and rims?

[kargidesign]

@limbota 3racing

[Tiberium29]

Is this the Turnigy 1220 or not???

Grreat Car i have the MHR

[Bartibizzle]

Hey man sweet Micro T i am amazed at the speed. What are some upgrades you recommend?

[kargidesign]

hanks man, have you watch the 54mph speed run of this baby?

My big recomend can be: "dont go brushless, if you are not ready to spend a lot". Becuase without a DSM or FM radio, good esc (ezrun18, quark22a) and 3s lipo you wont enyj it.

othr thn tht, threaed shaft is mst have for starters, annying e-clips :)

bearing, and bearinged transbox (alu one, I recomend all 3r parts, avoid atomic at all cost) is also required if you wnt your lipo modifed mcro lst long.

visit microforum for more

[rooboy2008]

Hey man, I love what you have done with your little Micro. I hope I can get my little Micro B to your level one day....

Great videos.... keep up the good work.

[kargidesign]

thanks a lot man. Dont worry she will, modding a micro is unavodible :P Take good care of your B, they are vintage and rare by now, also sweet.

Hopefuly videos will countinue at the end of january.

[NovaDinastiaDrummer]

Crazy micro-t! the best i ever saw!

Good work!

[pocketfighter1]

nice work

[kargidesign]

thanks dude, see the 54mph speed run of this setup on my vids :)

[kinc128]

wow serious stuff! can u handle it in the track?

[kargidesign]

thanks. check out her 54mph run than, on my videos :)

[pancake954]

61mhp is just to fast for that thing lol!!! what do u have on that to go that fast??!!

[kargidesign]

just 4s lipo :)

[camerongoll]

hay karigdesign i like the recent videos you have posted also i subscribed about 3 weeks ago

[kargidesign]

thanks for the comments and subscription dude, appriciated.

[camerongoll]

hay man i have the 3racing aluminum gear cover but mine is blue with like a little black cover on it how come your is all blue

[kargidesign]

mine just fell off dude :)

[Burdymac1]

so i need some info.

i have the 8750kv brushless with a 2s7.4 lipo.

i want to fit the 11.1lip and use the 10250kv brushless.

my question to you being that you seen to have some experience with it is can i fit the 11.1lipo in it even if i have to modify?

and how much faster is the 10250kv brushless compared to what i have now???

awsome micro by the way, would love to see a street vid of it.

[kargidesign]

You cant fit 3s on battery hatch of micro-t. You can put the esc there and 3s on top. Or buy a 3r chassis and do what I did. But 3s without a quality radio (DSM or FM) wont be meaningful since you will out of range before reaching top speed. On dyno same setup 50kmh on 2s, 80kmh on 3s, +100kmh on 4s. Thanks, a demorilazing crashed happen on last speedrun, waiting for parts, stay tuned for street video.