i think you need a honey bee fp and quit waisting so much money of crashes and replacment parts, then when you can hover get a better more expensive heli... ALSO LEARN to fly tail in first.
remember to let go of the speeder when reach the ground in the end of a crash. Otherwise it could lead to serious damage of other parts of the helicopter.
1 more thing to mention, dun overrun your heli cause it hurts the lipo badly, also when the voltage drops it loses headspeed, meaning losing the tail control at the same time...
New video day 9 I'll upload today after the rebuilt, much nicer handling still need to figure out what headspeed I should run it at. Getting DX6i TX this week.
Also don't care about these lipos they're just cheap junk, when I pay more than $40 for a lipo I'll start to take care but these came with the heli heh. I only got to use one today before I smashed the heli and ruined a servo. The crash in this video didn't chip any servo teeth! And I use washers to balance the CG but the heli was out of whack on that day. Anyhow, subscribe and you'll see when I upload the next one much better hovering I think :)
hi mate, i think ur heli needs professional setups haha, it didnt seem well balanced (blace tracking, vibrations etc), especially the tail... but i still would suggest setup up the king 2 probably coz it is a good trainer... Trex 450's parts are expensive and more precise setups needed for that...
Hey, yeah I had problems that day. I rebuilt it and it's now smooth I also replaced the rear plastic with CNC alloy tail although I found I didn't have all the damn parts so had to use half CNC and one part plastic but I got the tail setup pretty good. I know I'm going to make a mess of a T-REX so will keep at this a bit longer!
use a training gear that save your heli. and keep it up everybody is a beginner at first time.
callofduty1944 1 year ago
i agree. Esky sucks. Lots of problems with the HBK2. Start fresh with the Exceed G2. too
JPHLIPERS 3 years ago
i think you need a honey bee fp and quit waisting so much money of crashes and replacment parts, then when you can hover get a better more expensive heli... ALSO LEARN to fly tail in first.
limpnut80 3 years ago
ESKY quality sucks, TREX 450 is what you should be recommending. This was 5 months ago I can hover inverted now.
clintwr 3 years ago
remember to let go of the speeder when reach the ground in the end of a crash. Otherwise it could lead to serious damage of other parts of the helicopter.
malisiod 3 years ago
I try to hit throttle hold when going in but don't always get the chance. Thanks for watching.
clintwr 3 years ago
haha, the crash at 1:42 is very funny:P..
Fun to see you learning! Keep´em rolling!
RcAntax 3 years ago
Thanks man. Check out day 13 for some high flying park action.. ha!
clintwr 3 years ago
1 more thing to mention, dun overrun your heli cause it hurts the lipo badly, also when the voltage drops it loses headspeed, meaning losing the tail control at the same time...
AhRoyRoy85 3 years ago
New video day 9 I'll upload today after the rebuilt, much nicer handling still need to figure out what headspeed I should run it at. Getting DX6i TX this week.
clintwr 3 years ago
Also don't care about these lipos they're just cheap junk, when I pay more than $40 for a lipo I'll start to take care but these came with the heli heh. I only got to use one today before I smashed the heli and ruined a servo. The crash in this video didn't chip any servo teeth! And I use washers to balance the CG but the heli was out of whack on that day. Anyhow, subscribe and you'll see when I upload the next one much better hovering I think :)
clintwr 3 years ago
hi mate, i think ur heli needs professional setups haha, it didnt seem well balanced (blace tracking, vibrations etc), especially the tail... but i still would suggest setup up the king 2 probably coz it is a good trainer... Trex 450's parts are expensive and more precise setups needed for that...
AhRoyRoy85 3 years ago
Hey, yeah I had problems that day. I rebuilt it and it's now smooth I also replaced the rear plastic with CNC alloy tail although I found I didn't have all the damn parts so had to use half CNC and one part plastic but I got the tail setup pretty good. I know I'm going to make a mess of a T-REX so will keep at this a bit longer!
clintwr 3 years ago
The heli handstand.....hahahaa!! Getting better noob :)
chikishell 3 years ago