@cncmotorsports I have and chevy 383 I'm building with>>> Scat forged I beam rods, I believe a 4130 eagle crank, 10:1 forged pistons, air gap intake, AFR 195cc SBC Eliminator Competition Heads & a Lunati Hydraulic roller 535/550 Lobe Separation at 108, 1inch 4hole hamburger carb spacer, AED 850 HO-Modified Series or should I go with a 750? How Much Horsepower do u think I can get with that set up?????????????
and i hate that i never can get motor to stop leak a lil oil. i dont want any oil at all to drop. was yall return policy on oil problems email me joshsumpter88@yahoo.com
i want so get it rebuild. i know the motor is balenced right and the block is decked and the bored was check and everything was right. i just want to put a set of new piston and ring in it the motor runs good still but its hurt. whats yall process. in incoming motors.
im from south carolina. and i have a 383 stroker. the motor was built right. but i let the wrong guy crank it up. and set the timing wrong. the motor was spark ratling. and i was driving it for a whole a got down on it a few time. then it had a blow by problem when i got the guy pressure test it.he said i had alread cracked the piston. so he checked all the cyclenders and saw that two if them were dead. i want to get new set of pistons. the motor was re balenced and re check to make sure
i got a brodix aluminum headed 496 big block eagle roatating assembly brodix intake .714.714 solid cam and a 1050 dominator . would it help out that setup ?
Is there any way u can email me a build sheet on this engine and the price for the whole set up in the video carb and all i working on a 64 nova i think this would be the perfect engine my email is dadirtyboy52@yahoo.com
This has been flagged as spam show
@cncmotorsports I have and chevy 383 I'm building with>>> Scat forged I beam rods, I believe a 4130 eagle crank, 10:1 forged pistons, air gap intake, AFR 195cc SBC Eliminator Competition Heads & a Lunati Hydraulic roller 535/550 Lobe Separation at 108, 1inch 4hole hamburger carb spacer, AED 850 HO-Modified Series or should I go with a 750? How Much Horsepower do u think I can get with that set up?????????????
desmosis 1 month ago in playlist 383 Motors
what do guys rev these to with the scat 9000
LoganTheRedneck 4 months ago
@LoganTheRedneck
Around 6800 RPM
cncmotorsports 4 months ago
What are the cam specs
Weightz101 5 months ago
@Weightz101
We don't share cam specs.
cncmotorsports 5 months ago
and i hate that i never can get motor to stop leak a lil oil. i dont want any oil at all to drop. was yall return policy on oil problems email me joshsumpter88@yahoo.com
Cutlass81383 7 months ago
@Cutlass81383
All our engines are dyno tested, so if there are any leaks, we take care of them before they ship.
cncmotorsports 7 months ago
i want so get it rebuild. i know the motor is balenced right and the block is decked and the bored was check and everything was right. i just want to put a set of new piston and ring in it the motor runs good still but its hurt. whats yall process. in incoming motors.
Cutlass81383 7 months ago
im from south carolina. and i have a 383 stroker. the motor was built right. but i let the wrong guy crank it up. and set the timing wrong. the motor was spark ratling. and i was driving it for a whole a got down on it a few time. then it had a blow by problem when i got the guy pressure test it.he said i had alread cracked the piston. so he checked all the cyclenders and saw that two if them were dead. i want to get new set of pistons. the motor was re balenced and re check to make sure
Cutlass81383 7 months ago
i got a brodix aluminum headed 496 big block eagle roatating assembly brodix intake .714.714 solid cam and a 1050 dominator . would it help out that setup ?
1986montecarloss496 10 months ago
@1986montecarloss496
Yes, it should pick up a few horsepower.
cncmotorsports 10 months ago
why is it that the spacer makes that much difference ? what does it do ? if its like that ill buy one just to get that little bit extra .
1986montecarloss496 10 months ago
@1986montecarloss496
Spacers typically help on all intake manifolds. There are times where they do not help.
cncmotorsports 10 months ago
Is there any way u can email me a build sheet on this engine and the price for the whole set up in the video carb and all i working on a 64 nova i think this would be the perfect engine my email is dadirtyboy52@yahoo.com
inthemudk 1 year ago
@inthemudk
I just sent you an e-mail, get back to us with any questions you may have.
cncmotorsports 1 year ago
Wht makes your ignition so special! How much is it?
infamousnova 1 year ago
@infamousnova
We used all MSD, I believe this particular one we used an MSD billet distributor with a few minor upgrades.
cncmotorsports 1 year ago
whew 6,600 rpm. i wont bring mine up that high lol, im scurred.
rroberts383 1 year ago
That is amazing. This is exactly the kind of engine I've been looking for in a future street car build. Hydraulic roller, pump gas. Very impressive!!
blade7764 1 year ago
Dart 200 heads make on the average 30-40 HP less. Now if you CNC ported the dart heads, then they will make great power.
cncmotorsports 1 year ago
great results ,, wonder what it would do with ,, lets say , a Dart 200 Plat. head ? Is that an option available ?
levisnteeshirt 1 year ago