homemade powder coating oven

[quitblazing]

@christiandagalea they are just the elements out of any general electric oven. If you look on google or eBay they have them for sale. What I did was posted a add on Craigslist for a unwanted oven and a guy gave me one. Then I bought one for like 20 buck and ripped it apart and scrapped the rest. If you have a hard time finding them let me know. I'll send you a link for them.

[quitblazing]

@kid617 the light is simply a regular light out of any oven. I took the assembly apart and used a hole saw and cut the hole through bot pieces of panel. I left the outside uncovered so I can take the wires off quickly and remover the door. Also the metal is 24 guage. We have a 26 foot break at work and that's where I had everything bent.

[Kid617]

hey great build i want to do the same but i gotta see how to wire up my outlet my question is did u put the light from the oven or do u have to get a speacial light an buld for heat

And how did u bend the sheet metal an what sie gauge did u end up useing srry for all the question

[CHRISTIANDAGALEA]

wasup man can u help me wire my elements?? what elements are you using

[quitblazing]

I have the link for the site for a diagram but it won't let me post it. I'll try from my laptop when I'm off work

[quitblazing]

@mjd1957utube I will sen you a message with a link to a similar oven where you can get a wiring diagram. My elements were out of regular electric ovens. I just ripped 2 apart that we're similar and they had the general GE burners. The insulation is 2 inch fiberglass board insulation I got a bundle for 85.00. Also the glass was the glass off the oven doors. Just pry it open and remove the seperator.

[mjd1957utube]

I would love to have the wiring diiagram to build your oven and more detail on the eleaments / insulators used for the mounting...... looks like you have built a oven ibn high demand I;m redoing a 72 suzuki and well might as well do it all myself,, any additional info would be great also as noted in another message, i assume the glass uses was cut from typacal oven door glass

thanks

[quitblazing]

@kid617 let me know what u need help with man I'll respond ASAP. I used the glass out of a oven. It's tempered glass. I just took the door apart and used pity panels of glass, I sealed it with a high temp sealant from Mc Master Carr. It's like a dark red color. I got the temperature guage from a store called do it best, Just like a little hardware store. It was made to sit in a grill. I popped it out the little holder and sealed it also in the small holes I cut. Let me know if u need help.

[Kid617]

what kind of glass did u use

[Kid617]

deff like the build looks good i deff need to hit u up for what kind of materal u used good build

[quitblazing]

@pootytang 64. No once it's cure it good. Loom at all the engines that have parts powdercoated at car shows. It holds up good.

[pootytang64]

i seen you did an exhaust pipe. wouldnt the powder re liquify when the pipe gets hot?

[quitblazing]

@maxpower14843 I do have a thermostat in the main box. But for now I just put em on full blast and it works fine.

[maxpower14843]

Do you have some sort of theromstat control for the coils or are they just on full blast the whole time it is turned on?

[quitblazing]

@41point2 what I would do is check and make sure your getting juice in the wires at all. It can be something as simple as a loose ground , or bad contact. Let me know after you check it all out.

[41point2]

This is brilliant. Thanks for sharing Big Time, bro!!!

I have a question regards the wiring of the burns. I have a 3 coil oven, a friend built. Haven't used it for about 4 years. When I plugged it into the 220 we have, it was dead. I'm looking to rewire the 3 coils bi passing the oven control switchs he put in so I have a simple on and off. Is there a chance you could direct me to a wiring diagram for 3 coils?

Once again I love seeing vid's like this.

Thanks so much.