Added: 2 years ago
From: Sucram212
Views: 55,007
Sort by time | Sort by thread (beta)

Link to this comment:

Share to:

All Comments (456)

Sign In or Sign Up now to post a comment!
  • dopo tutto il tempo che continui a provare che si accenda si sarà ingoffata

  • guck mal nach der zündkerze ob se sauber is wenn nicht neue einbauen.....

  • The fuel filter on these restricts to much gas. Take it off and replace it with a straight line from the tank to the carb.

  • step one ur retarted step to did u put gas in it step 3 choke step four idle step 5 spark plug and most ov all step 6 don't get chines pieces of shit and buy a 125 yamaha

  • Zündkerze.^^

  • ismokewead420 there is nothing wrong with it it still runs it just needs a tune up ive been working on minibike since i was 6 or 7 and both of the ones ive got right now had that problem so just clean the carb clean the coil and clean the spark plug

  • the float is most likely stuck cause with all the bikes ive had theyve had this problem or clean the coil

  • Change the spark plug

  • Is it in nutreal call me I can fix it

  • take the engine apart and let the learning of shitty engines begin in other words its scrap

  • buy a new carburettor and ride on the carbburettor :L ok

    

  • lean it to the left and youll see fuel leaking then put it up right then try starting it

  • STEP ONE :KEEP PULLING THE ROPE ...IT WILL EVENTUALLY BREAK

    STEP TWO: THROW IT OUT AND GET OMETHING NOT MADE IN CHINA

  • clean the jet

  • Take your spark plug out and check if it has black crap on the end, if it does clean it mate and before you put it back in put a tiny bit of petrol in the spark plug hole and put the spark plug back in. Give it a pull on the pullstart and twist the throttle at the same time. If that don't work clean your carburettor and remove and clean your air filter. These are simple little bikes if they don't run it's either air, spark or fuel not getting to engine. Good luck mate- hammy

  • give it some gas

  • if anyone has problems starting their pocket bikes here are 3 tips

    1. Clean out the carbureter

    2. take the spark plug of and clean it

    3. Make sure your petrol (gas) is fairly new.

    i had the same problem with my bike and it took me about 30 mins to fix.

  • Check the CID

  • I just bought the same pocket dirtbike.. there is no petrol being sucked up into the piston for ignition via the spark plug.. when i put a smaal drop of petrol into the place where the spark plug goes and put back in the spark plug it works but then cuts out because more petrol isnt being sucked in.. Can Any1 help me?

  • you carborator is stuck all you need to do is open it up or hit it with a spanner to unjam it i had same problem with my pocket bike

  • dude im having the same problem did you fix it?

  • had trouble with mine was just the cheap spark plug that came with it

  • try turning the fuel filter round the right way. The rounded end points to the carb and flat end at the tank could help

  • its either the spark plug, or some internal engine defect.

  • its a chinese bike it wont start dipshit. I rode my old chinese 125cc 3 or 4 times and it just stopped. thats why I got a jap bike

  • make sure your oil mix is rite !!!!!!!!!!!!

  • Hey if any one can tell me what is wrong with mine it be awesome

  • check spark plug or clean out your carburator(:

  • 1. controll if the engine gets fuel 2. clean your carburator 3. check your membrane 4. check your flywheel 5. check the spark plug

  • something happened to me there was oil in my spark plug wash out the spark plug

  • @Shadow26b it's called the spark plug booy and that thing you call a white thing is a fucking sparkplugyou idiot.and the plug is probaly fucked if it is a ngk.

  • dude replace the pipe that brings gasoline to your motor

  • hmmm is there any gasoline....lol

  • yo dude i know why. you have to take the black rubber thing off. its like where the piston thing is and so ya you take that off then theres gonna be like this white thing which you'll need to unscrew then you take like a cap full of gas and put it in there. close it all up and stuff then itl start. i had the same problem :)

  • You guys are all wrong it"s probalay the fucking bushings that making it harder to pull snd your probally fucking weak

  • just trying to turn it on for 40 seconds wouldnt help you...last time i had mine started, i was pulling constantly with my friend for over 5 minutes until we got it

  • they would have to be over 100 diffrent thing that could be wrong with this but it was posted back in 2009 and i bout he has it sitten around for someone to tell him what to do, and wtf is up with your bars bro? aha

  • You only need to check 3 things 1. Comp. (had plenty). Spark (make sure its blue) 3. Fuel (this is wat it would be). If you cant get it going by taking this advise... Then you need to do 2 things...1. Start crying... 2. Go steal one from another fool who would own one of these things

  • You seized the moter

  • @900impulsed the motor isnt seized if he can still pull the starter cord... wise up !!!!

    probably just dirt in the carb or maybe needs a new plug

  • hi it wont be seized or ote what it might be is ur fuel mixing make sure it is exactually 25:1 2 stroke mix and shake it well mate and make sure u have the choke on

  • U need a carb 4 it I'm a macanick

  • @swena93 wow a mechanic who cant spell mechanic lol

  • new spark plug

  • had the same problem yo i got the saluuuuuuuution put ur legs on the pulling thing and pull it sooooo hard it worked for mee im soooo happy tell me if it worked

  • hey u might have just killed the engine take it to any garage that deals with bikes a garage near my house did it for free for me coz it was so easy for them .............

  • what would be strange is this piece of chinese starting!

  • tips

    1: petroll unleaded petroll and a bit of 2 stroke

    2: strenght pull it as hard as possible

    3: engine check to make sure every thing is in correct your ht leadt hight tension lead may be loos that starts the bike

    4: if all fails buy new one or dont go biking

  • you cant gas and than starting

    i do it so and its work

  • mix gas and oil.

  • put gas in it ;)

  • there's a carb thing on the bottom and there's a screw on it open that and the flooded gas will come out then screw it back on and it will start

  • firstly, try giving it some trottle but keep a brake on. also try turning off/on choke and fiddling with the fuel : air ratio on the carb?

  • Could be bad gass.

  • i got the same problem i got 2 stroke and and brand new spark plug but still wont start plz plz help

  • clean the carb and jet the spark plug with air

  • @minitom99 Jet the spark plug ?? What are you talking about ??

  • if you looked it looked like he engined overflowed so what im thinking is u need to clean it or change your spark plug mate

  • These things always need repairing... Mine pretty fucked up every time i went out on it... Stay away from Chinese bikes!

  • @Thumpstarrr yea get japanese :D they make the best animes so am sure there bikes would be just as good well mine is xD

  • You can see clearly the fuel pipe is disconnected. And these don't have keys, only the newer models do. If it's not that then the bottom end of the engine is most likely gone, from full revving it on a cold engine.

  • take out the spark plug and clean it

  • pulisci la candela o smonta il carburatore dopo sono moto cinesi

  • spark plug???

  • It's not starting because it's a shit bike

  • it there 2 stroke in it if not then the petrol is 2 strong 4 the engine

  • you probly need to clean out the carburator or you need a new spark plug

    

  • pulisci il carburatore 

  • clean the airfilter and spark plug.

  • probably piston and ring.. it was doing that on mine too

  • smooth you fluded it

  • and put gas and oil in to

    

  • how did you win it

    

  • pull the carby apart and clean out the jets

  • Use start-spray ?

    

  • HELP!!!! i have a mini dirt bike and it leaks every time i try to start it,and sometimes leaks when i just put petrol in it.CAN YOU PLZ REPLY ND HELP THANKS!!

  • @minidirtbike3 new flot in your carb sound like the solution to your problem

  • if u have it hotwired unconects the wires which connect to the key place and try i started mine like that

  • check the spark plug

  • I`D LAUGH IF IT STARTED DURING MAKING THIS VIDEO

  • its got water in it

  • Uhhhh get your day to pull it lol

  • Español... Hola amigo mira yo tengo una de esas y pues no funcionan muy bien por que son chinas, mira el problema puede ser, que esten cerradas las mangueras de la gasolina, otra cosa puede ser que sea la bujia, otra, adentro de el jalon trae una cosa negra que es la me manda la chispa a la bujia, esa se daña muy seguido y esta un poco cara, esta entre 20 y 50 dolares nueva, bueno espero que te sirva y lo puedas traducir saludos

  • make sure the oil and gas is 50|50

  • you have flodded to spark plug take it out and dryit and it will work mate

  • Im no genious just kidding i am but im pretty sure that the problem that theres a little piece of shit where the engine should be p.s. The whole is shitty too

  • get a new carb

  • how do u know when your idle is near perfect. Also my 49cc dirt bike turns off when i take it to full speed for a little while. ANY SOLUTIONS???

  • Step 1: Throw bike in garbage,

    Step 2 : Get a real dirt bike, Problem solved !

  • try replacing the spark plug

  • check the oil

    what are you mixing the gas????

  • check the oil

  • is ur ignitor bad

  • pump the gas bubble then try to start it but when u pull it give it sum gas

  • CAN anyone help me my pocket bike sameone ans that the ignitio button wont start it off but the pull work and my bike i dont really like pulling it cause some stime itoo lazy to revit on the road and get off and pull it cn somebody please hel me the ignition button does not work

  • ha ha check the magnet it may be lossne check if u have spark in no then check the thing that i said

  • one put a new pull start on the plastics break check your carb and pipe and fual line 

  • flooded????

  • Try a new spark plug and make sure you are adding the right amount of oil and the right kind of oil to your gas.

  • There is only one thing to do Wen all goes rong and can't fix it ....THROW DAT SHiT IN DA BUSHES... Na jp ihave da same probblem smh

  • put a bit of fuel on the spark plug then screw the plug back in

  • @charlienethercoat094 u mean oil

  • @charlienethercoat094 on these bikes its a mixture of oil and petrol , i think the ratio is 100 to 25 or somethin......in other words fuel :P

  • Try hitting the gas as you pull

  • connect the fuel pipe try that besides im geting yamaha ttr90,ttr125, and a yz 100 and yz125

  • @Sucram212 try turning the choke on make sure not to give it gas when your pulling it the choke should either be a knob you pull out on the side of the carboretor if that doesnt work take the spark plug out and see if it is black from oil on the threaded end if it is take some sand paper and sand it and clean the oil off if it starts but bogs out you probably have some bad gas or got some dirt into the pet cock or carboretor drain the gastank take a air squirter and clean out the jets

  • @harout121 its not an electric start idiot it doesnt have a key

  • check the spark plug and clean it.

  • buy quick start and spary on the carborator (air filter)

    

  • the kill switches on them are messed up so take the switch apart and make sure the wires are no touching etc then try that

  • wtf?? r u in belleville ontario canada?, i bought a bike tht looks JUST like tht, person said it runs, but it was all taken apart so i fukin order a new clutch, new spark plug, new pull start, new carb, and i just went to try it and it doesnt do shitt!

  • clean the carb

    

  • omg this bike is fail

  • check the spark plug i mean idk those things suck when they brake there done

  • try the srark plug and if its realy black get a wire brush and a wash cloth and wipe all the gas off then spray some starting fluid on the spark plug and give her a go

  • if that dosent work let it sit for a day or two cause you might have flooded the engine. then try again and if that doesnt work try to cold start it. and if that doesnt work go see a mechanic and ask him 4 advice or go buy another one

  • im getting my 2nd one turn the key on put the choke down and then turn the white nob up and put more fluid but dont flood the bike

  • Fix the engine, then put it on a weedeater, use that weedeater to work with a lawn mowing company. Make some money, and buy yourself a real bike.

  • empty the tank clean the enigen out get a new spark plug then put fuel in it along with a cap full of 2 stroke or 4stroke what ever it takes

  • Hold the throttle wide open and then start it... Only for 2 strokes never do that on a four stroke

  • i have a x18 u shud save up $650 and go buy one

  • dude these bikes cost like 150 dollars, ofcourse is going to broke after too days, i bought many off does now for my little brother all of then getting broked

  • check your spark plug or you might have flooded it

  • ill take tht

  • try getting a new plug

  • by new ............for reaper the cost is 100 e

  • wahrscheinlich hängt der schwimmer baue den mal aus und bau ihn wieder ein danach müsste es funktonieren

  • check the spark if theres no spark then its eather a new spark plug r a new cdi unit

  • i think its water and fuel in the engine, happend to mine

  • @darksariman how do you get it out ?

  • @thekaseem27 a whole lot of WD40, it's a spray

  • @thekaseem27 a whole lot of WD40, it's a spray, where the spark plug is on the cap you take it off and the gasket must be ripped witch is letting water in or some thing witch that is block something that goes up and down so, when you pull is hardly moves, there should be a black circle thing when you put your hand in where the cap is, you spray that

  • try and clean the carb

  • the bikes not fucked it the starter engine and it cost alot u might aswell buy a new one

  • i use to have one of those and i had the same exact problem get some starting fluid spray in the airbox but not to much and quickly pull start it if it cranks and dies open up your crab and check the float arms if they are bent flatten them and then put it together and start it up. thats how i fixed mine

  • dreh an der vergaser schraube ganz einfach die am ver ist mit so ner feder

  • wot you do is twist the throttle and press the front brake and at the same time pull the pull start if it does not work then it is the spark plug screw the spark plug of and then take a peace of metal and touch the metal to the bottom of the spark plug then pull the pull start and see if there is a spark if not then you need to buy a new spark plug . :>)

  • that thing looks like a kidney

  • @mrcool0975perry ur retarded

  • @GodIsLove531999 just saying.... u have to admit it kinda duz

  • check that the kill switch isnt broken. i had that problem as well.

  • press the gass n hold it for a few seconds then try it wen yuh smell gas then its gonna start Good Luck!!

  • if you have not used it in like 2 weeks you have to change the gas becuase petrol go stail and dosent start so just detach your fuel pipe from carb drain and refil

  • petrol

    carb

    spark plug

    coil

  • try car boosting it

  • spark plug

  • evt kein benzin^^

    no petrol xD??

  • yes you can try putting a little bit of gas in the carb if it still does not start it could ether be your spark plug or your coil try checking them

  • check the spark plug

  • je hebt de motor verzopen.. XD

  • i had that problem this morning and i cleaned the insides and know it works! hahahahaha

  • he qdo re mal el video no arranca

    jeje cmprate una nueva jeje

  • I can`t speak english but put a little bit gas in to the cilinder

  • check piston rings and carb

  • get some 1 to hold the front of bike and then use both hands to pull ass hard ass u can but i have a metal starter so u might break plastic 1 :O

  • take apart your carb poor the gas out and take out the jets to see if they are clean. look though the jet to see if you can see through it if you cant blow hard into the jet. Also when you get a new spark plug you have to gap it to the correct gap. And with two strokes you need to change the plug often. If the gap is still at the right size and the plug is black get some fine sand paper and sand the burned oil/gas mix off and but make sure not to mess up the gap.

  • Try taking the spark out and rest it on a good ground (engine block) attach the ht lead and pull once or twice (on the pull start) insuring theres a small spark between the prong and plug... Then re insert spark

    Next ensure the choke is in the down postion for a cold start this will allow a little more fuel to flow into the cylinder

    Next adjust the idle screw on the side of the carb (small brass flat head screw on thr left of the carb!)

    After all this make sure the fuel is switched on and try

  • There is a few things you need to do/check 1. is the ignition key on 2.is the fuel on 3.give it some choke 4. check all the wiring and the fuel line if you have done all those things try starting it with some revs aka turn the throttle towards you a bit

  • pistons arent firing needs new engine

  • CHINA

  • hey m8 if hiss stuff didnt work i also know that stuff cas i have a freakin workshop for them and 5 motorcross bikes and 2 mini dirt bikes you see the fat bit at the bottom forgot what its called take it of the bike and there might be oil clog as sometimes happen and i have to go now to fix my dirtbike cas i reved it up to mutch so engine blew not literly on fire like inside

  • Mix first of all new fuel mixture. If the engine still not start now screw the spark plug out and check how the electrode gap. If the engine still not start open the float bowl of the carburetor and screw up the nozzle clean out everything and screw. A little tip, the nozzle is clogged, so they probably think with pliers and heat it with a lighter or gas burner then solves the problem - important to let them cool before you install! Now the engine should run .

  • hi there can someone please help me out! i just bought a 50cc mini moto....and i must have put too much of 2 stroke oil in, so when i took most of it out it was all pink lool, so then i put some petrol in in without 2 stroke, and it just dont start up, my spark plug only sparks a little? is it ment tu spark dat much? its just i little twitch not like a propa spark! please can someone please help me out!

  • umm first you get a big garbage bag, then put it in, then take it to the dump, or you could skip the bag part, whatever you prefer

  • Try taking out the spark plug. If there is black stuff on it it means you have flooded the engine which you would have done after 100 pulls. Then try starting the bike with the spark plug off. if stuff comes out of where the spark plug hole is. Thats goos. then clean the end of the spark plug put it back in and away you go!

  • take off the air filter witch is on the carb witch is the little thing that hangs off the motor take off the ait filter and spray some aerostart in the carb because the carb will be cloged up with oil from the 2 stroke petrol or americans call it gas so spray it in there and your bike should get up and running again but dont spray too much or else you will flood the motor

  • prim it or turn on the choke

  • there is a screw in the bottom on the carb unscrew it make sure youre gas is off then screw it back in and turn on fuel and i bet you it will start

  • is the key wierd up or try the

     idle

  • i have the same bike my one did not start i bort some easy start be for you use it where you put the key a bit further down their is a gold screw keep half Turing it UN till it will start but put some easy start on the air filter but don't ceap using it or ur engine will get adide

  • just go buy some quick start from canadian tire of something spray it into the carb and pull it would start wit no prob

  • the bike is a piece of crap get a new one!