PMR Bolt Maintenance

[OSMxLOBBIES]

AHHHH SLOW DOWN IM TRYING TO KEEP UP!!!!! HAHAHA

[joeyang0423]

thank you that it make me know how to clean pmr's bolt.

Can i ask a few question?

how is the pmr08's operating pressure?

sorry i have a poor english ...

[danthebubba]

PLEASE HELP!!!!!!!!!!!! THE CAP OF MY BOLT CAME OFF AND IT IS NOT GOING BACK ON DO I NEED A NEW CAP OR WHAT AND MY BOLT IS IN MY GUN

[kookkamajunga]

@danthebubba try to push the bolt from the front with your finger. If that doesn't work get a swab and push it out with that.

[danthebubba]

@kookkamajunga thx for the help i manged to get it out with an allon key but sadly my caps threads got fucked up so i need an aluminum cap

[spyderRuLeZ]

reccomended upgrades?

[yegge17]

go techt lube!! :D:D

[gazzguy]

dude! I love u..

I had a problem with my pmr 07 a whole day of playing! So when I got home I saw this video, now it totaly works!:D

Olive ftw=)

keep the videos coming man!

[ColeNorCal]

I have an 07 too, gazzguy.

07s are the best!!!

[gazzguy]

@ColeNorCal

yes, It shoots better then my angel i think.

[crymetimeg9]

can anyone help me. i have a 07 pmr and i got a new metal bolt cap but it dosent seem to be going in all the way, i can still see a gap. If anyone else have this problem and found a way to fix it plz tell me it would be very helpful. I also tried putting the bolt cap in without the bolt andit gose in all the way fine but for some reason when i put the bolt and cap together there is a gap

[HardcoreGamer773]

i have the same problem but havnt found a way to fix it. any help?

[grizzlyboi5]

the back cap pops onto the bolt by the o-ring

[joostingee]

how often do you have to lube it ?

[kookamajunga]

I usually do before every time I play. But you can go about 3-4 cases without lube, assuming you didn't break a ball during that time.

[dsgballer]

the reason you cracked it is b/c you tghtened it to tight it should only betightened as tight as you hand can tighten it

[TalentZuK]

how can you tell if your solenoid is leaking?

[kookamajunga]

There will be a leak that sounds like its coming from the gripframe

[xaceofspadesx9]

i have all of the screws. should i back 1 out, and can i screw any too far in? im not new to painbtball just the pmr lol

[kookamajunga]

well, if you have them all, just back the one that is supposed to be in the groove out a little bit

[xaceofspadesx9]

thats what i did. my back cap is really really loose. thin its the o rings? they could probably use a change anyway

[kookamajunga]

hmm, it could be that. Is you back cap plastic or metal?

[xaceofspadesx9]

its metal

[kookamajunga]

ok make sure it's in all the way. On mine I have to push up on the backcap to get it to go in completely. yours may be like that

[xaceofspadesx9]

i'll give it a shot. push it down or up?

[kookamajunga]

On mine, its up, but its because my back cap has a machine error on it so it doesn't go in smooth unless I do that. Just make sure it goes in all the way and its tight

[xaceofspadesx9]

still loose. thanks for trying

[xaceofspadesx9]

i dont have the little notch that sticks out. what would cause this?

[kookamajunga]

it just means you lost the screw, I did too. Just make sure the hold is lined up with the slot when you put the bolt back in.

[TalentZuK]

Im having leaks from either the macroline or the top of the solenoid/bolt area. Any ideas?

[kookamajunga]

Well, for macroline, replace it and/or replace the fittings.

For the bolt, replace the orings.

as for the noid, I doubt it broke because dye uses fairly tolerant noids, but if thats the problem, It'll need replacing.

[GnarSchlopShred]

pmr a sear tripepr?

[kookamajunga]

Nope. Spool Valve

[Colby1095]

dude my pmr chops paint so much and i only had it for 2 weeks u think its cause of the bolt----i use good paint too so thats not the problem

[tenntitanfan25]

thank you soooo much

[pb4life0]

dude pmr's like alot of lube u need to drench it kinda like more then u put on

[kookamajunga]

all of that lube you put on there is getting shot down the barrel and coat it in lube. It will make your shot less accurate.

I've used this gun for a full year now and I haven't had a single oring break so I think the amount I use is working

[heriberto392]

owned lol

[ktown4life1337]

if any 1 is interested we're accepting new members into the PMR owners group on the techpb forums. PM me if you're interested.

[erwer66]

um my whole bolt didnt come out i was like wtF???? the back cap only came out i tryed to take the whole bolt out but it wouldnt budge then when i was screwwing the cap back in the big o ring snaped so i had to replace it a lube it but can u help with the backcap and the bolt plz

[kookamajunga]

well to get the bolt out, get a swab and push it through from the front. Then just re attatch the back cap.

[erwer66]

k thanks dude ill try tht

[mattwg2009]

how do you re attach the back cap?

[kookamajunga]

just gotta push it on, it takes a lot of force.

I put a towel around the end of my bolt and the back cap and put them in a vice and slowly cranked it tighter while I worked it on there

[sk8punk123]

i have the pmr and there seems to be a leak from the bolt, i noticed, that the black little thing you pointed out in 3:33 isn't there on the bolt, all the o-rings seem to be ok, so im thinking that the missing black thing is causing the leak but im still not sure, any ideas?

[kookamajunga]

there is a o ring that holds the back cap in, have you checked that? It's kind of hard to get to.

Also, I'm not sure if that little guide screw would cause a leak

[lapointe1333]

Hey please reply...my back cap came of when before it was on...how do i fix it?

[kookamajunga]

screw it back in? You may have stripped it. In that case you need to buy a metal one

[lapointe1333]

no haha the cap literally came of the bolt..idk how to fix it

[kookamajunga]

Oh! ok, you need to make sure theres a O-ring on the groove on the underside of the back cap and you need push it back in. It will be pretty difficult since you need to squeeze the oring in past the back of the bolt.

[eclipsegts03]

u did not even lube it that good the inside of the bolt where that o ring is u forgot.

[FataLXShotss]

just lube the whole bolt

[ktown4life1337]

are you happy with the pmr? I just bought 1 online and cant wait to test it out

[kookamajunga]

I'm extremely happy with it

[5050racing]

do u have to use lube specificly made for paintball?

[kookamajunga]

Yep, don't use anything that isn't specified for paintball.

[hi9400]

thanks this should help a lot how often do u hav to lube thats wat i wood like to know

[kookamajunga]

I do after every time I play.

[JEWDOOMAGIK94]

have an issue with my PMR. The gun shoots a ball perfectly once then when i shoot again it doesnt shoot. Also the bolt in the back is sticking out about an inch and its stuck i cant push it in or take it out. SOMEONE TELL ME WTH TO DO PLZ

[kookamajunga]

That's weird. If the bolt is half way out, that's why it doesn't shoot correctly (duh). Air isn't properly getting into the gun.

If you could make a video of it that'd be great. But I think your best bet is to take it into a paintball shop and get it looked at.

[JEWDOOMAGIK94]

nevermind i got the boly in correctly. i think i may have a leak becuase i fell air coming from somewhere in the handgrip of the gun. And i also get the blinking grgeen light, any idea what that is??

[kookamajunga]

hmm, air shouldn't come out of the grip, there should noyl be a small puff coming out of the back cap, but that's from how the guns made

The green light means something is in the breech. It should only appear when you are shooting

[JEWDOOMAGIK94]

k i fixed everything thx for ur help though

[wicked23s]

how often should i clen my bolt?

[kookamajunga]

After every time you play. Judging that you use a case a day, you bolt is moving 2 thousand times. If it does that frequently without care, it will wear out.

[1SmartParts1]

do you think smartparts sleek lube will work good for the pmr

[kookamajunga]

Yep, I have some sleek I use on mine. Its been good so far.

[polishdannybob]

Y do u need to take the firing can off, i didn't see u lube it?

[kookamajunga]

I do at 2:19. Well, the part that it slides on, and thats what needs to be lubes

[wicked23s]

good video now i know how to do it. i was scared i would fuck it up. but it look easy. thanks alot.

[fatalblade17]

question, why did u take off that one o-ring?

[kookamajunga]

Because the firing can wont come off if its on.

[MLGHennigX]

great video this helped a ton

[CloverdaleColts]

thanks alot for the vid dude, easy as that :p

[EWM27]

good deal man, thanks for showin me what i gotta do.

[Pmriscoolgun]

awesome vid

[Pmriscoolgun]

hey cool video, it helped me learn about cleaning the bolt (der). But i have one question. How do you take off the plastic back cap, and put on the aluminum one

[kookamajunga]

When you take out the bolt, theres 4 very tiny screws where the back cap attaches to the bolt. You unscrew those (be very careful they come out in about one turn and they're hard to find if you drop them)

After you take the plastic one off, you just re-attach the metal one. I'll do a video of it when my metal one arrives.

[kookamajunga]

I would get a o-ring that fits better. I don't know how big the one you have in there is, but judging by how a PMR works, that o-ring could really kill your air efficiency.