I have a half pipe outside for skateboarding, do you think this resin would make the surface smoother and last longer and be strong enough to take a beating? How thick should it be? I would be covering 8 4'x8' pieces of OSB board, roughly how much would this take and whats and estimate on the price?
@GCTeleVision You would probably be better off gluing a smooth hardboard product like Masonite to the surface of the OSB. If you want to use resin, epoxy would be best. Apply a coat for penetration and bonding, then build up coats for smoothness. Our One-To-One General Purpose Epoxy would most likely do the job for you. It will require at least 3 gallons, and probably more depending on how much build up you want. Check our website for prices. It is listed at the end of the video.
Awesome and informative video, has helped me alot in my first couple of practice resin projects. I do have a question about the mylar. I have been researching the product online and it would seem there are several products that entail the name mylar. Can you tell me exactly what type of said mylar that you used on the table? Thanks so much
@MSnipes78 Mylar is a brand name. The material is polyester film and other manufacturers will give it other names. The only way to know if a particular film will work is to try it on a small area. Make sure you are using film at least .005" (5 mil) thick. Thinner film will tear too easily.
how heavy does this 24"x24" resin get? I plan on doing a tabletop this size for a modular table for wargaming, and I wonder if this will be to heavy to transport.
since I use metric system, i am confused by most of this apart from the 24x24 Is it normal formula for Volume V= l*w*h .. I got a bit confused at that part
would would be the best bottom layer if I want to resemble outer space? wood in desired color, or some acrylic?
Your formula is correct. If the resin is .75" thick, the formula for the volume would be 24x24x.75=432 cubic inches. There are 231 cubic inches in a gallon, so this table required about 2 gallons. Resin weighs about 9 pounds per gallon, for a total weight of about 18 pounds. If you want to use the metric system, you can figure on 3785 cc's per gallon.
Either wood or acrylic could be used for the bottom. You will need to experiment to determine what looks best. Definitely do a small trial run before attempting a large and expensive project.
@davrv07 The catalyst ratio depends on the temperature and volume. We used under 5 drops per ounce. Note, that polyester resin does not cure to a glass smooth surface. It will require either the use of Mylar or sanding and buffing as described in the video.
I use this product to make kife handles and game calls. It's great stuff and polishes out very nicly with a buffer. You can also add some glitter as your mixing the resin for effect along with dyes that are also available. GREAT tutorial!!!
Great Video.I am doing a project to obtain a onyx/marble effect poured into open moulds of 2 cm in thickness.Should i building up the thickness in 3 to 4 pours?what is the out come if i a do a single pour to build up a 2cm thickness?
@nellore007 You are describing the way cultured marble vanity tops are made. Multiple pours are highly recommended. Thick pours tend to build up excessive heat which can warp and crack the casting. If there is enough filler material (such as marble dust, etc) which reduces the amount of resin, then thicker pours are possible. It is best to experiment to perfect the process.
I want to make a fun house mirror based off your table top video. How thick does the thinnest point need to be? Or is this even possible since it will only be supported by the outer frame?
@hyperflexharrington5 It is not clear how you will make a mirror out of the casting resin. Why not use acrylic mirror, available from TAP Plastics? It is easy to flex like a fun house mirror.
i have a granite tabletop that has a crack in the plastic like glaze, also a missing piece. can i use this product to fill in the missing piece also, would it keep the cracks from spreading?
@jamielovinlyons For this application, epoxy would be a better choice. It has better bonding properties and does not shrink when it cures. You could use either Ultra-Glo or Marine Grade Epoxy 314 Resin with the 109 Hardener, both available at TAP Plastics
I've seen this done before and wanted to do it on a table that will be outside on our full-sun patio. Will the resin yellow over time with the sun exposure? If so, is there a sealant that will prevent this? Thanks!
@suzi13137 We have not seen the resin yellow, but the surface is affected by the weather. It can lose its glossy shine. Automotive paste wax can help prevent that. If necessary, the top can be sanded and buffed to a shine with a power buffer.
hi i got one question, im doing some tables for a friend and its my first time using resin im sanding them scraping them since they got a coat of lacquer and stain, living only plain wood
how can i apply the resin without messing up the sides ?
I have a half pipe outside for skateboarding, do you think this resin would make the surface smoother and last longer and be strong enough to take a beating? How thick should it be? I would be covering 8 4'x8' pieces of OSB board, roughly how much would this take and whats and estimate on the price?
Thanks
GCTeleVision 3 weeks ago
@GCTeleVision You would probably be better off gluing a smooth hardboard product like Masonite to the surface of the OSB. If you want to use resin, epoxy would be best. Apply a coat for penetration and bonding, then build up coats for smoothness. Our One-To-One General Purpose Epoxy would most likely do the job for you. It will require at least 3 gallons, and probably more depending on how much build up you want. Check our website for prices. It is listed at the end of the video.
tapplastics 1 week ago
Awesome and informative video, has helped me alot in my first couple of practice resin projects. I do have a question about the mylar. I have been researching the product online and it would seem there are several products that entail the name mylar. Can you tell me exactly what type of said mylar that you used on the table? Thanks so much
MSnipes78 4 months ago
@MSnipes78 Mylar is a brand name. The material is polyester film and other manufacturers will give it other names. The only way to know if a particular film will work is to try it on a small area. Make sure you are using film at least .005" (5 mil) thick. Thinner film will tear too easily.
tapplastics 1 week ago
how heavy does this 24"x24" resin get? I plan on doing a tabletop this size for a modular table for wargaming, and I wonder if this will be to heavy to transport.
since I use metric system, i am confused by most of this apart from the 24x24 Is it normal formula for Volume V= l*w*h .. I got a bit confused at that part
would would be the best bottom layer if I want to resemble outer space? wood in desired color, or some acrylic?
rvchrono 4 months ago
Your formula is correct. If the resin is .75" thick, the formula for the volume would be 24x24x.75=432 cubic inches. There are 231 cubic inches in a gallon, so this table required about 2 gallons. Resin weighs about 9 pounds per gallon, for a total weight of about 18 pounds. If you want to use the metric system, you can figure on 3785 cc's per gallon.
tapplastics 4 months ago
Either wood or acrylic could be used for the bottom. You will need to experiment to determine what looks best. Definitely do a small trial run before attempting a large and expensive project.
tapplastics 4 months ago
whats the ratio of resin & catalyst in the last phase (in order to make the surface become like smooth like glass) ? thanks for the answer !
davrv07 5 months ago
@davrv07 The catalyst ratio depends on the temperature and volume. We used under 5 drops per ounce. Note, that polyester resin does not cure to a glass smooth surface. It will require either the use of Mylar or sanding and buffing as described in the video.
tapplastics 4 months ago
thanks.
seymour5575 5 months ago
how hard does this resin gets after ite cured?could you make a desktop with this resin.
seymour5575 5 months ago
@seymour5575 It is very hard; harder than a wood desk top.
tapplastics 5 months ago
Does the sand absorb the resin? If I use more sand am i going to need less resin?
xXxNickyJxXx 6 months ago
@xXxNickyJxXx Sand will displace resin. More sand means less resin.
tapplastics 6 months ago
I use this product to make kife handles and game calls. It's great stuff and polishes out very nicly with a buffer. You can also add some glitter as your mixing the resin for effect along with dyes that are also available. GREAT tutorial!!!
HeirloomGameCalls 8 months ago
Great Video.I am doing a project to obtain a onyx/marble effect poured into open moulds of 2 cm in thickness.Should i building up the thickness in 3 to 4 pours?what is the out come if i a do a single pour to build up a 2cm thickness?
nellore007 9 months ago
@nellore007 You are describing the way cultured marble vanity tops are made. Multiple pours are highly recommended. Thick pours tend to build up excessive heat which can warp and crack the casting. If there is enough filler material (such as marble dust, etc) which reduces the amount of resin, then thicker pours are possible. It is best to experiment to perfect the process.
tapplastics 6 months ago
I want to make a fun house mirror based off your table top video. How thick does the thinnest point need to be? Or is this even possible since it will only be supported by the outer frame?
hyperflexharrington5 11 months ago
@hyperflexharrington5 It is not clear how you will make a mirror out of the casting resin. Why not use acrylic mirror, available from TAP Plastics? It is easy to flex like a fun house mirror.
tapplastics 6 months ago
i have a granite tabletop that has a crack in the plastic like glaze, also a missing piece. can i use this product to fill in the missing piece also, would it keep the cracks from spreading?
jamielovinlyons 1 year ago
@jamielovinlyons For this application, epoxy would be a better choice. It has better bonding properties and does not shrink when it cures. You could use either Ultra-Glo or Marine Grade Epoxy 314 Resin with the 109 Hardener, both available at TAP Plastics
tapplastics 6 months ago
I've seen this done before and wanted to do it on a table that will be outside on our full-sun patio. Will the resin yellow over time with the sun exposure? If so, is there a sealant that will prevent this? Thanks!
suzi13137 1 year ago
@suzi13137 We have not seen the resin yellow, but the surface is affected by the weather. It can lose its glossy shine. Automotive paste wax can help prevent that. If necessary, the top can be sanded and buffed to a shine with a power buffer.
tapplastics 9 months ago
THANKS IT WORK
EDWCAV 1 year ago
hi i got one question, im doing some tables for a friend and its my first time using resin im sanding them scraping them since they got a coat of lacquer and stain, living only plain wood
how can i apply the resin without messing up the sides ?
EDWCAV 1 year ago
A heavy coat of paste wax will help, apply to the sides and as well as underneath (as resin flows over the side and drips down)
tapplastics 1 year ago
nice work, thank you for sharing
rraammiirreezz 2 years ago
Would this work for a desk? Or would that be too much use for it and it has a higher chance of getting scratched.
Monk3yman77 2 years ago
How easily does something like this scratch when used as a table like in your application.
LordoftheReef 2 years ago
The material will scratch but not easily; if the scratches become too noticeable it can be repaired by sanding and buffing.
tapplastics 2 years ago