BB Smack Gen V 6.4MMW test

[nuurgedi]

Keep a way the multmeter from the heet!

[EletrikRide]

@nuurgedi

There is no heat issue here, and the meter is perfectly safe and working as it is supposed to.

[moffett8]

How can this cell with no current leakage have a MMW of 6 and the 24 v cell which doesn't have the cells isolated have a MMW of 9-10?

[EletrikRide]

@moffett8 Because the more cells you have in series back to back, the more efficient the stack is - to a point. I explain this in the video.

[CrimsonSnow]

hmm. not sure what this (kinda looks like computer liquid cooling or something) but hey well done! 5*'s!

[EletrikRide]

It is a hydrogen generator

[hhoguru232004]

I got the same problem once you get into high efficncy the heat is nill

[hhoguru232004]

I posted a new cell your welcome to take a look at seems we have two zero current leakage cells. I just avoided all the tubeing and other stuff. I'll post some more desighns when I finish getting well this back surgery has really slowed me down for a year. Best wishes B

[EletrikRide]

I'll check it out!

[hhoguru232004]

So the bar is set at 6.4mmw since it is a zero leakage cell there should be nothing more efficent capable of being produced.

Please post the exact numbers your getting Volts Amps Temp and LPM just so people have it. Is this the long awaighted Zero Leakage Boyce Desigh dry cell or is his still unreleased cause the MMW is pretty good on this one.

[EletrikRide]

Thanks, I have posted the exact parameters in this video. This may be the highest MMW's for the temp, but my new titanium design kicks the crap out of this.

The MMO ti substrate material blows all the rules of hydroxy out the window.

[bentwheel1]

have you any idea how many amps and lpm before the ecu fights back??? without any sensor adjustments...

thanks

[EletrikRide]

Way to many application variations to be able to answer that - so no. You have to tune per install.

[mikepowers420]

Way to go, Smack. Your constant innovations and improvements show just how much you test, and read the forums. I know you have some folks out there that try to put you down, and say that your stuff is Crap, but they don't know their sphincter from their brain pan. Have you seen the vid that's directly aimed at slamming you, the one with the computerized voice ? I wont bother to post that turd of a link in here. You work Way to hard on your vids to spoil them with it.

Keep up the good work..

[EletrikRide]

Thanks! And I took care of that loser. It took me a while, but those vids were finally pulled down after repeated requests.

[argosy2006]

is quad unit ready yet?>

[EletrikRide]

Yes it is. You can find it on my site under products

[55Calibre]

Very good video,i am interested in how you will put this together.

[EletrikRide]

I will show you guys soon

[RVhydrogen]

Hi ER I hope it will be soon soon.

I'm working on a cell that runs cold like yours.

Grate work keep it up!

[insAneTunA]

Hi E, Great setup, again. Was wondering how you are doing, hope everything is fine with you and your kid. Take care and greets from the Netherlands, iT

[EletrikRide]

Thanks, we are hanging in there!

[BUILDER1STCL]

smack hahaha ' builder here you are so close ! just got my turbine . have an 15 plate sytem? melted post on seconddary battery you have all the componets to do what we need . you showed us all . godspeed smackman.

[tontoboy1]

Very cool man, I am very excited to see how you put this all together. Way to think outside the box, you are a true innovator. I noticed on your video description that you said approximately 2.5 lpm, but you filled your container in .52 min which would put it under 2 lpm unless I am missing something. Not trying to bust your chops but I was just curious. Keep up the good work!

[EletrikRide]

1. Cell is green, way green.

2. Only drawing 21 amps. Rule of thumb - 1LPM per 10 amps. So broken in it should make 2.1LPM. So You are not missing anything - unit is performing exactly as it should. Unit can take 25amps max, so broken in it will make 2.5LPM.

[GmanBB]

Dear, Dylan! Nice work!

I need you advice on B Smack subject. I build one with 240 plates, can I get your mail to ask some questions?

With best regards,

[EletrikRide]

Hi, email is on my site homepage

[oruval]

This is direct current? I was curious, has anyone ever tried AC ?

It would eliminate the need for a PWM if done correctly.

[EletrikRide]

Ac brute force on a cell like this would make a great steam generator.

[oddssodds]

Hey Smack,

Posted a question on the hydroxy boards, but didn't see my posting.

I like the look of this cell. Are you evacuating the liquid from each cell separately? How are you re-introducing the liquid?

You can reply directly to poberman66ATgmailDOTcom

[EletrikRide]

I will be making a video that goes over the operation of the cell in detail.

[higherpoweredh2o]

Looks good. Cant wait till more testing is done....

Good job bro, I will be getting back to work soon on this hho stuff, So much to do so little time....

Godspeed my friend.

Keep up the good work.

[EletrikRide]

Thanks! Thought you might appreciate the diamond config. This is the cell I will be using on my next wave of genset tests.

[EletrikRide]

Good luck!

[HydroGenHybryid]

hey smack what is the mcmaster # for the pvc gasket?

[EletrikRide]

look up "pvc sheet"

[ashtweth]

Smack what a leap of technology from Gen I, i still use Gen I, Gen one still kicks ass. Looks great Smack thanks for posting. I got the promo Vids for Gen IV ready, just waiting for the new dyno with J's, sorry its taking so long, will update now with the new cells.

[EletrikRide]

Right on! This is what we do, bro!

[water2gashawaii]

Hey smack, good to see you are back showing vids of your cells. Always nice to see what others are doing or finding.

Bill

[EletrikRide]

Thanks Bill - never stopped!