homemade goped project

[gangsterbryce]

fuck that two stroke do not need any back pressure to run they just need th epropper jetting if yout running a differint pipe

[pyroman675]

dude that bracket going up and over then back down over the wheel you could use for a part of your motor bracket, have it up top and over that bracket dont have it habging over the side so its a pain in the ass to steer

[bobchessy]

sweet im doing something like this exept i used the razor mx 500 u can see my latest vid of me riding it

[banana1783]

its because its not a high perfornamce carb so it has know high or low jet and dont use that other carb it will break evenually because its not for that use i did that on my old goped sport and it broke my motor while i was rideing so now i have a bigfoot but should be a fun project any more questions message me

[Motorfordtoyota]

Im going to try doing this later in the year. I want to mount my engine over or behind the wheel so I have all the space to stand. Cool

[SNOOPDOG0707]

well it dependes on your price range. their are goped electrice scooters that can go up to 20 mph (on turbo mode). but 20 mph is the max. speed on an electrice goped. and the nicest electrice goped cost about $2,200!!! while the nicest gas goped cost about 1,100. personally i get more satisaction with a gas motor, because they go a hella lot faster, and you can put tons of mods on a gas motor.

[unknown707unknown]

lol don't you hate those epa people and tree hugers?

[firemaniac9999]

drilling the intake may increase the hp not by much on a small engine, but it is dangerous to get metal shavings near and in the cylinder, im not an expert but i would say the risks out wiegh the gains

[guitarguy3500]

do u thing 1.5 hp is big enough for a skateboard?

[snowman3514]

no they ared to run as best as they can so yeah the only thing you can really upgrade to give it more power is the exhaust

[azndude3141]

quik question, i have a razor e300 scooter that i dont like anymore because battery is getting weak. i am planning to convert it to gas powered but i dont know how i will attach the chain because it uses a small tiny chain and my clutch uses a regular chain. what can i do? is it better to just change the sproket or is it better to get a clutch that uses a tiny sproket for the tiny chain? plz help!!! thx for reading the whole message if you did. ;)

[09moodye]

i would get a better sporcet definetly

[mop6wewe]

yo check out my video responce i just sent u i did the same thing u were gona do and it gose faster then a real goped

[mop6wewe]

u suck im kidding but now that u got a goped ur not gona build this i wanted u to make it

[datokid]

the reacon why the carby has no adjustment and it is set to the factory setting but if u can get a walbro carby or something and i would put the chainsaw carby on it and it should give it more touque and keep the muffler on becouse it will give u more touque and will be alot quiter but good job and nice engine

ps if u want it to go better without puttin new rings in it i would use a little bit of octane booster or use higher octane fuel and good luck

[minibike45]

u need back pressure

[suzuki834]

try turning the back weel around so sprocket is on other side then atach sprocket frome the electrik motor to your weed whacker motor bolt6 it down put on the chain and you cant ride it

[smokey65662]

o cool.

All my vids are widescreen.

sweet.

[01DodgeRAM1500V8]

no problem i did it to my chainsaw 49cc walbro carb looks very similiar to yours but it works thats wh y i left ya a comment thanks for the reply man peace :) oh and the more back pressure the easier it will start

[01DodgeRAM1500V8]

yea man by opening up that hole for the intake/oil mix from the carb the more air that gets in therefor more power cool project man best of luck man peace

[smokey65662]

Thanks man. I will continue to update :)