I have an idea, when you are heating it and the black part gets torn off when you try to separate it, take the hair dryer and heat the black part up (still attached to the screen and after you torn it apart) and peel off that black part and glue it back on to the LCD screen. would that work?
thanks for clarifying this point! do you think this goes for the nano 6g as well? or might it be possible because of the small size of the screen? of course i wanted to save money just buying the digitizer.... but i didn't know before that its so diffifult to separate the two.
@Cintrojan It does not look like you can separate the digitizer on the 6g nano either. I am sure you can buy the front assembly for around 40.00 on ebay.
Evidence shown to some pricks that an LCD cannot be removed from the digitizer therefore should stop selling the digitizer on it's own.So More money down the drain due to cons that don't take refunds. I rate TechLifeMobile and would like to thank them for getting the point out.
thank you sir, you probably saved me 20 bucks. i HATE when videos that show you how to take it all apart but don't tell you that little detail. it would have only taken them 5 seconds to say, "Buy the assembly not just the glass, the two are inseparable" thanks again
Hi, is there any way you guys could send me one back cover and front cover , a broken one , please I really need one for a prank thank you , nice video btw
Hi , is there any way I could buy one of the broken screens please I need one thank you ( if it's only craked ) and I need a back too , it's for a prank I am going to do ony mom ) I'm going to change it , and tell her I broke it thank you
So if I were to buy the LCD and digitizer separately and buy the 3M adhesive film stuff they sell on eBay wouldn't I be able to stick the LCD to the digitizer using the 3M film and get it to work properly? I'm asking this because I want to switch my iPhone to mirror blue and the blue digitizer+LCD costs well over $70 and that's simply too much. If i buy these separately though it will cost $30 Thanks
@mendoza1017 do not put the adhesive between the LCD and digitizer the best thing to do is to position the LCD on glass after wiping both perfectly clean and trying to keep them in a place without much dust and use super glue around the edges of the LCD careful not to get any under it and don't use too much as to where it sticks up and causes it to not fit together just go around carefully not moving the LCD and seal it completely
yes you can. Do not remove anything from phone. start with the small pieces of glass, and using just a nail flick them off its actually easy. you need to smash the larger pieces into very small fragments. like less than 5x5mm dont heat it, dont remove it. Then you preserve your hq screen without having to buy cheap chinese copies which will crap out quickly.
@Kinematographer I keep getting responses like this. Please post a video in response to this one of it being done with before and after results. We have about 50+ broken screens with good LCDs laying around the office.
hey pm if you want to kno how to seperate them!....i found 2ways!..dont get me wrong it is still hard and you will mess up the first and second time!....but the glass will brake but the lcd comes out with no scratch!.....
@alexfeltham the resolution is just the same as the oem ones. I just fixed my ipod touch the other day, and honestly, i couldnt tell the diff between the retian display on the new screen and that of my iphone 4
and yeah you can separate it on the 4th gen, but it might not work out too well, get ur accessories from chinaphoneaccessories on ebay
@TechLifeMobile First of all i'm not saying i can do it.. But I will certainly not use a screwdriver to removed that LCD. You need to find a tool that can seperate the two object at once...
Was able to separate and when I assembled my iPod back together screen went white and off can't get to come back on should that mean my LCD is done for are do I have another problem
@Left2Dollars You can use a blowtorch if you want. Either way separating the LCD front the Glass is not going to help you. Buy the right part the first time and save yourself the trouble. You need the full front assembly with the digitizer and LCD.
I need help my vibrator module has two different parts i dont know how to put it back properly i have a pic but can't post it here it says error can you pm me please!
thanks so much for this video! I have been trying to crack this mystery since so long... I have a broken digitizer but the LCD is fne. Everywhere I see videos of people replacing "glass" which inludes the digitizer and the LCD, but nowhere did anybody tell that these two cannot be separated. You saved me atleast $20.
@Youtubie505 Yes depending on where you get them from. Our screens are OEM parts. You iPhone will look and function as when you first bought it from apple.
HI, MY SCREEN GLASS IS CRACKED BUT THE ACTUALL LCD ISN'T, WHAT PART DO I NEED TO BUY? AS I WILL NOT NEED A NEW LCD, AND WHAT IS IT CALLED? SOMEBODY PLEASE HELP!!
@The Yandman agreed
Can it even be done,i cant find vid showin it
bendaly 15 hours ago
I have an idea, when you are heating it and the black part gets torn off when you try to separate it, take the hair dryer and heat the black part up (still attached to the screen and after you torn it apart) and peel off that black part and glue it back on to the LCD screen. would that work?
Fizzyris 5 days ago
thanks for clarifying this point! do you think this goes for the nano 6g as well? or might it be possible because of the small size of the screen? of course i wanted to save money just buying the digitizer.... but i didn't know before that its so diffifult to separate the two.
Cintrojan 6 days ago
@Cintrojan It does not look like you can separate the digitizer on the 6g nano either. I am sure you can buy the front assembly for around 40.00 on ebay.
TechLifeMobile 5 days ago
Evidence shown to some pricks that an LCD cannot be removed from the digitizer therefore should stop selling the digitizer on it's own.So More money down the drain due to cons that don't take refunds. I rate TechLifeMobile and would like to thank them for getting the point out.
TheYandman 1 week ago
well im a dumb cunt who just bought the LCD screen when i cant even take the old one off
vetyu 1 week ago
Fuck you apple, make shit that we can actually fix!!
jojobeans37852 1 week ago
while you cant remove the lcd from the digitizer, you can still disassemble it. watch my water damage repair video where I show how to do this
6Italia0 2 weeks ago
thank you sir, you probably saved me 20 bucks. i HATE when videos that show you how to take it all apart but don't tell you that little detail. it would have only taken them 5 seconds to say, "Buy the assembly not just the glass, the two are inseparable" thanks again
blacksnow90 2 weeks ago
Hi, is there any way you guys could send me one back cover and front cover , a broken one , please I really need one for a prank thank you , nice video btw
mcdog83 4 weeks ago
Hi , is there any way I could buy one of the broken screens please I need one thank you ( if it's only craked ) and I need a back too , it's for a prank I am going to do ony mom ) I'm going to change it , and tell her I broke it thank you
mcdog83 4 weeks ago
NICE JOB JOBS!!!! NICE LEGACY!!!!!
ThaCorporate 1 month ago in playlist Iphone
this is cool but can someone tell me how to do this in reverse? i need to put a new lcd on a digitizer and i have the adhesive glue.
xdarkmario 1 month ago
So if I were to buy the LCD and digitizer separately and buy the 3M adhesive film stuff they sell on eBay wouldn't I be able to stick the LCD to the digitizer using the 3M film and get it to work properly? I'm asking this because I want to switch my iPhone to mirror blue and the blue digitizer+LCD costs well over $70 and that's simply too much. If i buy these separately though it will cost $30 Thanks
mendoza1017 1 month ago
@mendoza1017 You could try but i would not recommend it.
TechLifeMobile 1 month ago
@mendoza1017 do not put the adhesive between the LCD and digitizer the best thing to do is to position the LCD on glass after wiping both perfectly clean and trying to keep them in a place without much dust and use super glue around the edges of the LCD careful not to get any under it and don't use too much as to where it sticks up and causes it to not fit together just go around carefully not moving the LCD and seal it completely
TheChickenrun3 3 weeks ago
yes you can. Do not remove anything from phone. start with the small pieces of glass, and using just a nail flick them off its actually easy. you need to smash the larger pieces into very small fragments. like less than 5x5mm dont heat it, dont remove it. Then you preserve your hq screen without having to buy cheap chinese copies which will crap out quickly.
Kinematographer 2 months ago
@Kinematographer I keep getting responses like this. Please post a video in response to this one of it being done with before and after results. We have about 50+ broken screens with good LCDs laying around the office.
TechLifeMobile 1 month ago
hey pm if you want to kno how to seperate them!....i found 2ways!..dont get me wrong it is still hard and you will mess up the first and second time!....but the glass will brake but the lcd comes out with no scratch!.....
xxsurcentralxx 2 months ago
@xxsurcentralxx , can you please post a video showing how to. I am really interested. thank you
karacenaSlaoui 1 month ago
@xxsurcentralxx Yeah post a video. Everyone would LOVE to see it.
TechLifeMobile 1 month ago
how to attach it back?
gleb19961 2 months ago
@gleb19961 U r really dumb, it says you can't go it.
Janson540123 2 months ago
@gleb19961 i was wondering that too, i think you use some special adhesive, but i cant find any youtube vids telling me how :/
ferarri1993 2 months ago
What sort of resolution are the replacement (non Apple/chinese) lcds I wonder, do they look any good
Is the ipod 4th gen also impossible to separate lcd/digitizer
alexfeltham 2 months ago
@alexfeltham the resolution is just the same as the oem ones. I just fixed my ipod touch the other day, and honestly, i couldnt tell the diff between the retian display on the new screen and that of my iphone 4
and yeah you can separate it on the 4th gen, but it might not work out too well, get ur accessories from chinaphoneaccessories on ebay
ferarri1993 2 months ago
I bought the glass only. Can I repair it following this video? There is not black film :(
bigpeppe91 2 months ago
haha noobs dont wast ur time with that just spend ten more dollars on ebay to get them together.
reyeslovesmin 2 months ago
I just received the LCD and digitizer as a gift, they're separate. Is it going to be a problem attaching them?!? Help me... :\
donka5151 3 months ago
carnt you just heat the front up instead of dismantling the phone any answers ??
leef0324uk 3 months ago
I know HOW to seperate them! ;)
Hackyouruniverse 3 months ago
Thumbs up if you bought the glass only!!!
2615863 3 months ago 5
@2615863 How do you seperate it correctly so that it will still work?? I need help!!!
jshark716 3 months ago
@jshark716 You cant, there is another film that is stuck to the glass. I spent another $30 just for the Screen+LCD together
2615863 3 months ago
i managed to do it
namnam12344 3 months ago
@namnam12344 Please post a video of how you did it and what the finished product looks like. I am interested.
TechLifeMobile 3 months ago
Comment removed
caddington09 1 month ago in playlist Favorite videos
Comment removed
Jim1carrey 1 month ago
This has been flagged as spam show
@TechLifeMobile First of all i'm not saying i can do it.. But I will certainly not use a screwdriver to removed that LCD. You need to find a tool that can seperate the two object at once...
Jim1carrey 1 month ago
Comment removed
DjiboutienneBeauty 2 months ago
Comment removed
chudrocket 3 months ago
Was able to separate and when I assembled my iPod back together screen went white and off can't get to come back on should that mean my LCD is done for are do I have another problem
Ju3tfits 3 months ago
can i buy a lcd seperate and just attach that to the empty digitizer?
gjame11 4 months ago
why dont you try heating up the glass instead of the digitizer??
itschad411 4 months ago
can i use a hairdryer instead of heatgun?
Left2Dollars 4 months ago
@Left2Dollars You can use a blowtorch if you want. Either way separating the LCD front the Glass is not going to help you. Buy the right part the first time and save yourself the trouble. You need the full front assembly with the digitizer and LCD.
TechLifeMobile 4 months ago
@h8pikeys the long screw on the left the short on the right
foofenscoops 4 months ago
This has been flagged as spam show
bueno , en espanol , jodio las 5 pantallas tratando de separarlas
jrafael2005 4 months ago
bueno , en espanol , jodio las 2 pantallas tratando de separarlas
jrafael2005 4 months ago
This has been flagged as spam show
I need help my vibrator module has two different parts i dont know how to put it back properly i have a pic but can't post it here it says error can you pm me please!
h8pikeys 4 months ago
What's the point, u cannot put it back together lol
vd853 4 months ago
thanks so much for this video! I have been trying to crack this mystery since so long... I have a broken digitizer but the LCD is fne. Everywhere I see videos of people replacing "glass" which inludes the digitizer and the LCD, but nowhere did anybody tell that these two cannot be separated. You saved me atleast $20.
srujanmishra77 4 months ago
@srujanmishra77 Your welcome. I am glad you found this useful!
TechLifeMobile 4 months ago
@srujanmishra77 if you read the description they still say to buy whole front unit.
Reason for this is that if you try this, most chances are that you wil damage the LCD while attempting this.
cormyek9 3 months ago
BUT ARE THE LCD SCREENS the same high qualitiy as the normal original LCD screens from apple???
Youtubie505 5 months ago
@Youtubie505 Yes depending on where you get them from. Our screens are OEM parts. You iPhone will look and function as when you first bought it from apple.
TechLifeMobile 5 months ago
HI, MY SCREEN GLASS IS CRACKED BUT THE ACTUALL LCD ISN'T, WHAT PART DO I NEED TO BUY? AS I WILL NOT NEED A NEW LCD, AND WHAT IS IT CALLED? SOMEBODY PLEASE HELP!!
habzyg 5 months ago
@habzyg Reading the description below the video will answer your question.
TechLifeMobile 5 months ago
thanks, very helpful!!
JohnnyLover69 5 months ago
stop crying guys.
All the screens sold are made of glass + LCD
there is a liquid between the lecd and glass, to isolate from dirty elements. the result is you will never have something between glass and lcd
TheIDeathrow 5 months ago
Hi the glass is broke on my iphone 4 , Only the glass part , can i just replace the glass with out replacing the LCD ?
navannitronut 6 months ago
@navannitronut No. The glass is fused to the digitizer which is fused to the LCD.
TechLifeMobile 6 months ago
I broken when I tried do it in my 2g... fucking steve jobs!
paulopenh 6 months ago
but Chuck Norris can do it.....
mcg199426 6 months ago
fuck you again Steve Jobs!
NielssBohr 6 months ago 26
Hi my friend... after repair my front lcd+touch my signal wifi and gps are VERY VERY loss... do you know why? Sorry my english... thanks a lot !
cruschx 6 months ago
@cruschx did u fix it?
MrDeakujin 6 months ago
Good info thank you
mrsdgivens 6 months ago
Thanks for this video ... Now i know what to buy
Mexmade 7 months ago
Oh goddamn, why didn't I watch this before ordering the fucking thing?!
Lialice92 7 months ago 27
i did the same thing :(
2K5Cesar 5 months ago
I like the end bit. Directed by 'insert name here!'
NoelLloyd 7 months ago
agreed impossible
crginn143 7 months ago
You can actually try to use a "SMT Oven" machine it's not the same as heat gun
;)
maximka1819 8 months ago
One agian damn you steve jobs lol! Thanks for the detailed vid
h8ncars 9 months ago