Ok, my xbox has been repaired before and has metal screws with plastic and metal washers instead of the x-clamps, and it DOESNT have those little heat pads on the bottom of the mother board. Will i have to buy new heat sucker pad things??? And will i have to buy a new set of screws,washers,and plastic washers again??? Or do you think my xbox is fried:( Thank you for all your help. MY ERROR CODE IS 4 RED LIGHTS, 1 RED LIGHT, 4 RED LIGHTS, AND 3 RED LIGHTS IN THE PLAYER 1,2,AND 3. please help!!!!
@walmer23 If you don't want to use lint-free products on your electronic hardware that's your prerogative. Enjoy the permanent burn-in and poor contact on the thermal compound the residue will cause. But for the rest of us, who follow directions and common sense, we'll stick with the lint-free stuff.
Then they probably did it right. Less is more when it comes to thermal paste. It's the pressure of the heatsink against the chip that counts for more. If you have too much paste you'll just be making a mess around the edges with no extra benefit.
fucktard, at 2:12 you broke and ripped off one of the little squares on the side of the GPU, no surprise since you did put on you the CPU heatsink sideways on your RROD "repair" video
@TheBL00DAssassin Actually he should have 23 of those little blocks around his CPU, and by the looks of it he still does. It may have looked like it but it must have just been thermal compound, it is highly improbable that he managed to break one of those with just a q-tip. Unless before this video he got a hammer and screwdiver and chipped a way at it as to loosen it. Just an fyi
I'm fixing to clean my laptop CPU, thanks for this guide. Using the same stuff once it arrives, and I take it that getting the cpu/gpu all wet with this stuff isn't going to damage anything right?
so is it the actual heatsink melting, or that glue they use to put down the heatsink? And if its glue, do we need to put more glue on it to put it back?
Had rrod and did complete dismantle removed old thermal paste cleaned then reapplied new thermal paste to gpu and CPU. Turned on and still rrod "general hw failure". So stuck 2 precision screwdrivers onto fans and let overheat 10 min until rrod "overheat" 2 lights appeared. Let cool down. And now working?! Didn't do X-support kit fix. Don't know if I'm lucky or what but can't wait to play Duke Nukem Forever.
Good video but i cant tell where any of these places i need to clean are on the xbox. You should have showed us where they are one the xbox before cleaning.
His link redirects you to a very reputable and FUN poker website where you can win money without spending money, definitely not a scam. Great guides TripAces, found them to be a ton of help when fixing my xbox, only thing I would say is that you can use Goo Gone and then 91% isopropyl alcohol ($3 together at any grocery store) and get the job done just as well, if not better, and for cheaper. Just make sure you clean up all of the Goo Gone with the ipa or you could run into problems.
@trumanbeast99 The stuff i mentioned..I C Diamond...Either 7 carat or 24 carat.They also have the advantage that they aren`t electrically conductive so any accidental spillage wont short something out.
guys if your xbox 360 gets too warm just buy a air conditioner only for xbox 360 at cdon.com its cheap and it makes your xbox cold i have one and i love it <3
where can we buy a fuckn heat sink ,,,, damm all these videos telll u how to do it, but not where to get the fuckn stupdi ass componenets,, whick is the primier point , where to find this shit, and dont tell me staqples radioshack , cause they aint got shit
The cleaner solution touching the the whole unit the (the green chip) to remove the thermal compound on the outer part of the chip won't hurt the 360?
Cool stuff, i recently opened my Xbox 360 and cleaned the GPU and CPU of the older thermal compound and added my own Arctic Alumina cooling paste, will that lower the temperature compared to the stock paste that was applied at the factory? I think i experienced higher FPS and better flow in the games after that proceedure. Whaddya think?
so i have the E74 error. so i replaced the x clamps... the instructions i was using said after i do so plug in and let overheat. then 2 lights should appear. well i only had 1 light. stupidly i turned off and turned it back on... (this was to re-remove the dvd player. as i stupidly thought this might be the cause. then the xbox worked!! but only for a day. now i have E74. any ideas? overheat again? or do i needa do the thermal paste thing again too?
i know i commented before but you guys helped me after i did these steps witch was last month it worked until i earned my replacement one cant thank you guys enough =)
@Creamo223 Yes it work's with first gen Xbox 360's (universal), I just ordered my 2nd gen heat sinks for the GPU & CPU kit yesterday and extra heat sinks for the RAM modules just waiting for it to come in the mail today, I'll keep you posted on how the installation goes and if it fixes my RROD problem :-0
kan you use like super glue or something instead of artic stuff cuz cant get any around here and my xbox is already taken apart please reply really fast like
hey, I don't know where I can get a thermal adhesive remover thingy, do you think I can use like nail polish remover or sth instead? or would that totally ruin the xbox? pls help me fast, I need to play assassin's creed 2 :(((
Why does this work, why is this what needs to be done? I'm not questioning whether it does or not - someone asked me what was wrong with their xbox and i didnt know, i just knew to tell them what to do...so why is this what needs doing?
I dont know why, but some of the old Thermal compound isnt coming off the tiny chips by gpu and cpu. I have most cleaned out, except for a small amount i cant get out. Will this affect it at all? I have the cpu and gpu all cleanedoff.
So I cleaned off the thermal compound (Although I didn't use cleaner like you did) then I put some new thermal comp. back on (It was "ACME" white stuff from fry's, not arctic silver) and my 3 lights were still flashing when I put everything back together and turned it on. So should I now go through the steps to reset it (Like you showed in 1 of your other vids)?
I will redo the whole process if I have to, I want my 360 back! I haven't played in weeks and I'm "Jonesin"!
Thnx! Looks like I'm buyin myself a new one for christmas tho...I managed to break a tiny little chip off my motherboard! After much swearing (& browsing online for xbox MB's) I'm just gonna bite the bullet and get a new 1. I WILL say this though: My 360 ran fine 4 years with an intercooler, and died about a month after my intercooler died. So, does anyone know if the newest systems are still problematic? Mine had the improved heatsink, but I don't know if the new ones are still even better....
You're a pretty cool guy, thanks for puting all of these tutorials on. I have yet to go to your poker site though because I fear it is some sort of scam.
Will this also help to fix the Three Red Rings?
MissCindySmith 3 weeks ago
will rubbing alcohol work?
NickMercurio 1 month ago
lawl i just tryed that.. it didnt work i dont think haha i will try something else than a Q tip though hold on...
oGxC59Zz 1 month ago
what you did to the 4 chips that come with tape ?
did you put the penny trick ?
EndoftheRd 2 months ago
This has been flagged as spam show
Ok, my xbox has been repaired before and has metal screws with plastic and metal washers instead of the x-clamps, and it DOESNT have those little heat pads on the bottom of the mother board. Will i have to buy new heat sucker pad things??? And will i have to buy a new set of screws,washers,and plastic washers again??? Or do you think my xbox is fried:( Thank you for all your help. MY ERROR CODE IS 4 RED LIGHTS, 1 RED LIGHT, 4 RED LIGHTS, AND 3 RED LIGHTS IN THE PLAYER 1,2,AND 3. please help!!!!
PaulPierceFan365 2 months ago
SO, AFTER YOU CLEAN THOSE PARTS ALL YOU HAVE TO DO IS PUT ALL THE PARTS BACK TOGETHER THEN YOURE DONE? OR IS THERE SOMETHING ELSE I HAVE TO APPLY?
PaulPierceFan365 2 months ago
@PaulPierceFan365 You apply thermal paste on the cpu and gpu then over heat it for like 5 mins so it comes incontact and it should work
ParanoiaA22 2 months ago
Comment removed
PaulPierceFan365 2 months ago
with out thermal compound the cpu and gpu will just heat up in seconds.
ZaldivarRecords 3 months ago
Should be using lint free cloth for this, coffee filters instead of paper towels.. and the actual QTIP brand qtips, not cotton qtips.
UOGSammich 4 months ago
@UOGSammich you're wrong.
walmer23 1 month ago
@walmer23 If you don't want to use lint-free products on your electronic hardware that's your prerogative. Enjoy the permanent burn-in and poor contact on the thermal compound the residue will cause. But for the rest of us, who follow directions and common sense, we'll stick with the lint-free stuff.
UOGSammich 1 month ago
@UOGSammich dude, ive been doing this for years and never had any problems out of lint.... O.o
lashedcrayon 1 week ago
I removed my xclips and there was hardly any thermal paste on the cpus or heatsinks. MIcrosoft are criminals!
enigmaticbee 5 months ago 2
@enigmaticbee Mine was smothered in it. It was overflowing onto the board around the chips.
DejectedPanda 5 months ago
@enigmaticbee
Then they probably did it right. Less is more when it comes to thermal paste. It's the pressure of the heatsink against the chip that counts for more. If you have too much paste you'll just be making a mess around the edges with no extra benefit.
aredesuyo 3 months ago
razorblade takes the TIM off the Heatsinks like scraping a layer of room temperature butter off.
Kiraina 6 months ago
@Jakebell58 i have a wii. didn't rate down the video! wii sports +plus is win.
xxbrkdwnxx 7 months ago
Comment removed
XxWifeyMcBeatyxX 6 months ago
@XxWifeyMcBeatyxX ...what are you talking about? lol. respond to the wrong comment?
xxbrkdwnxx 6 months ago
Comment removed
XxWifeyMcBeatyxX 6 months ago
@xxbrkdwnxx Sorry about that, that was kinda weird how it replied to your comment.
XxWifeyMcBeatyxX 6 months ago
fucktard, at 2:12 you broke and ripped off one of the little squares on the side of the GPU, no surprise since you did put on you the CPU heatsink sideways on your RROD "repair" video
TheBL00DAssassin 7 months ago
This has been flagged as spam show
@TheBL00DAssassin Actually he should have 23 of those little blocks around his CPU, and by the looks of it he still does. It may have looked like it but it must have just been thermal compound, it is highly improbable that he managed to break one of those with just a q-tip. Unless before this video he got a hammer and screwdiver and chipped a way at it as to loosen it. Just an fyi
XxWifeyMcBeatyxX 6 months ago
@TheBL00DAssassin it was a chunk of thermal compound lol
Veksta 6 months ago
@Veksta ahh yeah, now that i look at it, it's thermal paste
TheBL00DAssassin 6 months ago
very good guide. ill be fixing mine here in couple weeks when i finally get time to fix it lol.
Trapdnmymynd4eva 7 months ago
Lol thank you- someone who doesn't put up obnoxious RATM music while trying to explain what to do.
baconboy222 7 months ago
I'm fixing to clean my laptop CPU, thanks for this guide. Using the same stuff once it arrives, and I take it that getting the cpu/gpu all wet with this stuff isn't going to damage anything right?
danman132x 9 months ago
so is it the actual heatsink melting, or that glue they use to put down the heatsink? And if its glue, do we need to put more glue on it to put it back?
chiefpacman 9 months ago
I can put "PC CPU" heatsink on xbox 360? and Xbox 360 slim?
Quadsmodo 9 months ago
not sure what kind of gum u chew....but the kind i use doesn't dissolve in my mouth :D
knoxville363 9 months ago
how i fixed mine:
1. open the xbox
2. get a fan
3. place fan direct to the heat sinks
4. Play xbox and be happy
Badlyfar 10 months ago
where can i buy this compound
KG125912 10 months ago
@KG125912
radio shack or online. its cheaper online.
look for arctic silver 5
bloodygoon09 10 months ago
@bloodygoon09 this did not work for me
KG125912 9 months ago
i have working 2006 old clamps 360. Should I redo thermal or don't fix what's not broken?
bought cheap 360 with dvd read error as only problem.
Full of dust and grim on board.
also is fine glass polish recommended for dvd lens?
CliveGains80s 10 months ago
would alcahale work?
ericngo77 10 months ago
@ericngo77 yes i think so...
supersimrishamn 10 months ago
A jobs to congratulate!
bryantpugh43 10 months ago
Great job!
antonioreyes1987 10 months ago
i love the video but its too complicated can u make a video from cleaning it from scratch
ad123468 11 months ago
Had rrod and did complete dismantle removed old thermal paste cleaned then reapplied new thermal paste to gpu and CPU. Turned on and still rrod "general hw failure". So stuck 2 precision screwdrivers onto fans and let overheat 10 min until rrod "overheat" 2 lights appeared. Let cool down. And now working?! Didn't do X-support kit fix. Don't know if I'm lucky or what but can't wait to play Duke Nukem Forever.
footshopper 11 months ago
Good video but i cant tell where any of these places i need to clean are on the xbox. You should have showed us where they are one the xbox before cleaning.
Pizzaman885 11 months ago
My Uncle is a manager of Fry's electronics. Haha lol :D
Xxx1Pwnage1xxX 11 months ago
This has been flagged as spam show
Go to your address bar, after the word YOU and before the word TUBE, type in "win" then press enter
TMiller397 1 year ago
5:16 lol!
DreamzModZzoCom 1 year ago
His link redirects you to a very reputable and FUN poker website where you can win money without spending money, definitely not a scam. Great guides TripAces, found them to be a ton of help when fixing my xbox, only thing I would say is that you can use Goo Gone and then 91% isopropyl alcohol ($3 together at any grocery store) and get the job done just as well, if not better, and for cheaper. Just make sure you clean up all of the Goo Gone with the ipa or you could run into problems.
hoboonaparkbench 1 year ago
3:50 thats what she said lol
chrisames1 1 year ago
how much is it for the thermal paste apporoxamitly
YungZ905 1 year ago
wow thats some good stuff! Arctic silver 5 is the best!
Kevinkoch2443 1 year ago
@Kevinkoch2443 That`s just not true.I C Diamond is way better.
Arctic silver is maybe the best known paste and it`s probably why people like yourself always refer to it.
JooHaxDemoTaken 1 year ago
@JooHaxDemoTaken what would you recommend to use
trumanbeast99 1 year ago
@trumanbeast99 The stuff i mentioned..I C Diamond...Either 7 carat or 24 carat.They also have the advantage that they aren`t electrically conductive so any accidental spillage wont short something out.
JooHaxDemoTaken 11 months ago
@JooHaxDemoTaken
Diamond pastes are like new stuff to consumers though. When all our old tubes of AS5 run out we'll all be on diamond pastes ;)
baneat 1 year ago
wat does that do
CinematicsHD 1 year ago
guys if your xbox 360 gets too warm just buy a air conditioner only for xbox 360 at cdon.com its cheap and it makes your xbox cold i have one and i love it <3
mizgog 1 year ago
how long does that last.... like how long will it be for the red rings to come back
analicia101 1 year ago
@analicia101 if u do it right, shouldnt come back
4892austin 1 year ago
my xbox will turn off if i play a game. usually when the graphics get intense would doing this fix it?
StupidTankProduction 1 year ago
can i clean it with hot water? or the thing that they use to clean the paint from the finger nails?
nikospneuma1 1 year ago
@nikospneuma1 u cant use that copound dont get off that ez u can use the remover or u can also use isopropyl alcohol
xxryanryanxx 1 year ago
where can we buy a fuckn heat sink ,,,, damm all these videos telll u how to do it, but not where to get the fuckn stupdi ass componenets,, whick is the primier point , where to find this shit, and dont tell me staqples radioshack , cause they aint got shit
junior1984able 1 year ago
@junior1984able its at radio shack dumass! itss hiding in the back
xxryanryanxx 1 year ago
@xxryanryanxx NO ITS NOT U PIECE OF SHITTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTTT
junior1984able 1 year ago
@junior1984able have you tried ebay?
StupidTankProduction 1 year ago
@StupidTankProduction yes homie,,,
junior1984able 1 year ago
I got a question can I use the sillicon heat sink compound or is there a different between theme
Godryu17 1 year ago
@Godryu17 no u cant man ok silver compound
xxryanryanxx 1 year ago
in a perfect world (at least in the PC world) you wouldnt want to get any of that shit on your motherboard or the circuit board for your GPU
DCSchecter 1 year ago
call me an idiot but i used go be gone...
codeman017 1 year ago
@CpGamer9786 It did for me! I also did the penny trick too!
Yelnuts71 1 year ago
@CpGamer9786 YES
WaPow132 1 year ago
will this arctic 5 compound give me lower temps on the GPU and CPU?
setarcos4131 1 year ago
@setarcos4131 yep
xxryanryanxx 1 year ago
will rubbing alcohol work instead of the thermal compound remover
evan12345 1 year ago
@evan12345 yes
guywith2names 1 year ago
Fucking microsoft puts on fail thermal paste. :D
eTnKT 1 year ago
@eTnKT have you seen the thermal paste on a ps3? i have its no different
super3slug 1 year ago
Comment removed
DawnyDarko 1 year ago
should i replace the x-clamps or just use it
itzjt900 1 year ago
This has been flagged as spam show
just keep rubbing it
omfgg3tlost 1 year ago
what is Heat Sinks and what does the thermal compound do? it wont hurt my 360 ?
WaPow132 1 year ago
@WaPow132 if u dont put the thermal compund on it will hurt ur 360
poooopnat 1 year ago
does this solve the e 74 problem?
beltran1690 1 year ago
The cleaner solution touching the the whole unit the (the green chip) to remove the thermal compound on the outer part of the chip won't hurt the 360?
AirCraft32 1 year ago
Cool stuff, i recently opened my Xbox 360 and cleaned the GPU and CPU of the older thermal compound and added my own Arctic Alumina cooling paste, will that lower the temperature compared to the stock paste that was applied at the factory? I think i experienced higher FPS and better flow in the games after that proceedure. Whaddya think?
HerrAfrikaKorps 1 year ago
what store can you buy thermal paste please help enyone ?????????????
robertgpc 1 year ago
I KGB this and they said it should be available at a radio shack
Mprunner119 1 year ago
@robertgpc buy it at radishack artic silver 10 ask for that
enchilada234 1 year ago
so i have the E74 error. so i replaced the x clamps... the instructions i was using said after i do so plug in and let overheat. then 2 lights should appear. well i only had 1 light. stupidly i turned off and turned it back on... (this was to re-remove the dvd player. as i stupidly thought this might be the cause. then the xbox worked!! but only for a day. now i have E74. any ideas? overheat again? or do i needa do the thermal paste thing again too?
slayerzzzzzz 1 year ago
alcohol works too but it will take a lot longer.
terroboy 1 year ago
WD 40 does the job great
sweetman1994 1 year ago
I want to thank you for this guide it helped me to fix my xbox.
elmace 1 year ago
Can you use something other than Artic clean????
Fatninja479 1 year ago
WD40
azrial4421 1 year ago
do you have to add more thermal compound after you have removed the bad 1
Beatlesfan46 1 year ago
@Beatlesfan46 Yes you do.
XxxSmgHunterxxX 1 year ago
i know i commented before but you guys helped me after i did these steps witch was last month it worked until i earned my replacement one cant thank you guys enough =)
spartanMRm17 1 year ago
thanks it worked/...
Reconciliasion 1 year ago
@14DarkMatt15 motherboards aren't going to break over littel stuff unlea you scratch the small wires
Yournotawhat 1 year ago
Are you wearing a your camera?
pr1zonerofwar 1 year ago
Will the 2nd generation heatsinks work on first gen 360s?
Creamo223 1 year ago
Comment removed
KijinnoKamen 1 year ago
This has been flagged as spam show
@Creamo223 Yes it work's with first gen Xbox 360's (universal), I just ordered my 2nd gen heat sinks for the GPU & CPU kit yesterday and extra heat sinks for the RAM modules just waiting for it to come in the mail today, I'll keep you posted on how the installation goes and if it fixes my RROD problem :-0
KijinnoKamen 1 year ago
@Creamo223 yes
IHI4ZZx 1 year ago
a cloth works better.
that just gets cotton everware
IAreCrazyChris 1 year ago
god dam there is so many "thats what she said" joke in this vid
KM4RTS3CUR1TY 2 years ago
just keep rubbin it till its all off
loser9110 1 year ago
@loser9110 Thats what she said XD
pr1zonerofwar 1 year ago
when u do this try not to touch the q tip to the motherboard
liv3les 2 years ago
man i did all of this. Worked for awhile. Now my xbox just over heats with 2 red rings when nothing is hot. Dont know how to fix it.
Tick386 2 years ago
googone works just as good
ChugAColdBeer 2 years ago
what the hell was that?sound 4:06
kcard707 2 years ago
kan you use like super glue or something instead of artic stuff cuz cant get any around here and my xbox is already taken apart please reply really fast like
montgomerychance 2 years ago
No...and don't try it or your 360 will overheat in an instant...
proximxr 1 year ago
dont work
MrCcsboy 2 years ago
This comment has received too many negative votes show
Wait, I have to add new thermal compound after cleaning it?
clybourn 2 years ago
yes
brunotecnohelp 2 years ago
hahah yeah. Really there is no chance on the old systems, just complete failure.
dirtastegood 2 years ago
hey, I don't know where I can get a thermal adhesive remover thingy, do you think I can use like nail polish remover or sth instead? or would that totally ruin the xbox? pls help me fast, I need to play assassin's creed 2 :(((
rolhinha1 2 years ago 2
Why does this work, why is this what needs to be done? I'm not questioning whether it does or not - someone asked me what was wrong with their xbox and i didnt know, i just knew to tell them what to do...so why is this what needs doing?
tomiguess 2 years ago
I dont know why, but some of the old Thermal compound isnt coming off the tiny chips by gpu and cpu. I have most cleaned out, except for a small amount i cant get out. Will this affect it at all? I have the cpu and gpu all cleanedoff.
dirtastegood 2 years ago
So I cleaned off the thermal compound (Although I didn't use cleaner like you did) then I put some new thermal comp. back on (It was "ACME" white stuff from fry's, not arctic silver) and my 3 lights were still flashing when I put everything back together and turned it on. So should I now go through the steps to reset it (Like you showed in 1 of your other vids)?
I will redo the whole process if I have to, I want my 360 back! I haven't played in weeks and I'm "Jonesin"!
nightmathzombieethan 2 years ago
you got to do the towel trick after you put it together
WiiKyler 2 years ago
u should use the penny trick for the 3 red lights thats a guarntee fix. just type in XBOX 360 PENNY TRICK i did it and it works
meckaone 2 years ago
Thnx! Looks like I'm buyin myself a new one for christmas tho...I managed to break a tiny little chip off my motherboard! After much swearing (& browsing online for xbox MB's) I'm just gonna bite the bullet and get a new 1. I WILL say this though: My 360 ran fine 4 years with an intercooler, and died about a month after my intercooler died. So, does anyone know if the newest systems are still problematic? Mine had the improved heatsink, but I don't know if the new ones are still even better....
nightmathzombieethan 2 years ago
Get an Xbox with the Jasper system in it. They are supposed to be designed to eliminate the chance of getting RROD
dirtastegood 2 years ago
The Jasper system? How can I tell?
nightmathzombieethan 2 years ago
If you buy a new system, it says it on the box. Jasper decreases the chance of rrod.
dirtastegood 2 years ago
K Thnx!
nightmathzombieethan 2 years ago
power brick(search) 09+
COOLGUY19A 2 years ago
Yup, got one, it runs a LOT cooler, thanks....
nightmathzombieethan 2 years ago
where do i get this stuff ? the Arctic Silver Thermal Compound cleaner
KiiNPiiN96 2 years ago
wait, isn't the thermal paste have to stay there? i mean that have to protect the GPU to not heat so much or u have to change it after some time?
kanetidus 2 years ago
can i use something else instead Arctic Silver Thermal Compound cleaner? Anyway great video,i hope i can fix my stupid E74
kanetidus 2 years ago
did u ever fix your e-74 problem because i got the same shit
meckaone 2 years ago
is this e73 please get back to me ASAP
Atokad75 2 years ago
ok i have 1 red light and when the av cord isnt plugged in it has no rings but as soon as i plug it in it gets the rings what does that mean
Seferothe 2 years ago
lemme guess... Xbox 360 Elite BAM!!!
superhans8 2 years ago
will this work for 2 red lights on Xbox (overheating)?
CBCrackman1 2 years ago
What stuff? It is Arctic Silver Thermal Compound cleaner.
TripAcesFull 2 years ago
wat that stuff
dewDGgamers 2 years ago
It's no scam... it's free!!! Just go there and you can see. Please leave a comment once you see it's not a scam. Thanks!!!
TripAcesFull 2 years ago
@TripAcesFull whats free
WaPow132 1 year ago
You're a pretty cool guy, thanks for puting all of these tutorials on. I have yet to go to your poker site though because I fear it is some sort of scam.
gooberzor 2 years ago