How to remove air restrictors in buzz bee shells

[jorgeslino1234]

can you shoot paintballs? that would be awesome

[rekrapnadroj]

I Had 4 Shells and Screwed them up, this is a terrible mod. dont do it

[TheKingNerf]

ur awesome!

[Protocol7DDGFX]

Got some tips for you folks:

Some shells are too loose to hold the dart. I used electrical tape to get around this. Still works awesome (if not better.)

You can hammer out the black piece too. I did it to my shells and they aren't deformed at all.

Hope this helps.

[24voldemort]

I got everything out exept for that little black piece I can't melt cuz I don't have anything to and now the inside of the shell has a few sraches and that black piece is beat to shit but back at the bottom of the shell and won't move I put a bullet in there and it shoots alittle better but I hear the bullet getting scratched as I put it in should I throw the shell out or keep it

[Liamwaffles]

3:16 earthquake!!!!!

[charlie12345610]

so we are basically paying for half a shell that we are going to drill and take out anyway?

just dont put them in and make us have an 18+ id card to buy them

[Twisted4000]

What is even the point of the air restricter in the first place?

[nosnhoj99]

so is this the only air restricters in the guns or is there other stuff to?

[ShadowSerris]

I have a question, how far does it shoot opposed to when it would be normal?

[autonerf]

@ShadowSerris The buzz bee guns have a range of 30 ft but the shells restrictors can reduce the range and sometimes not fire at all.

[MegaJohn334]

@autonerf would these shells still eject out of a buzz bee double shot?

[autonerf]

@MegaJohn334 Yes

[roosterboosterish]

like jeremy clarkson on top gear ''need a hammer''

[sigilvii]

I love the accidental SuperStrength effect at 3:25

[Unknown8186]

How come the newer ones doesn't have a spring? mine doesn't have

[ShadowSerris]

@Unknown8186 Because it's most likely more new.

[ShadowSerris]

@Unknown8186 Therefor it doesn't need a spring because it is built in.

[PosineosOfSparta]

you can just take some needlenose pliers and pull out the little stick

[tallyhofanback]

so once i take evrything out i ust put darts in load um and shoot ?

[BananaSlaps]

@autonerf hey bro, i love your vids,but can you make one on how to remove the ar in a hunter? i cannot find any on how to

[j9ace101]

you make so hard!

[kongufighter08]

It would be cool if the hunter used shells, it'll be like a real rifle xD

[mynerfgear1212]

the box says 6+ not 40+

[autonerf]

@mynerfgear1212 the box says who cares. I've got a thousand subs. 

[izze97]

@mynerfgear1212 6+ means 6 years and up

[ZelddaLinkFreak]

@mynerfgear1212 6+ means six and up, 40 is above 6 :D

[SuperKevin11]

do u have to have a sottering iron?

[jaygeoff111]

how does this affect the gun?

[101cgk]

there is an easier way , just hammer a nail down the little hole in the middle

[132oink]

3:26 looks like special effects lol

[The1masterc]

wat does removing the ar do?

[DarkArmedDuelist101]

Do you need the shells to operate the hunter?

[autonerf]

@DarkArmedDuelist101 The hunter does not use shells

[triggerdance]

@DarkArmedDuelist101 hunter replicates a single shot bolt action rifle only shotguns use shells. shells are differant from bullets. shells are capsules that hold about 50 hard leads balls that when fired, spread out so its almost impossible to miss a target at close range with a shotgun

[DarkArmedDuelist101]

@triggerdance I'm talking about toy buzz bee shells, not real shells.

[DarkArmedDuelist101]

Do you need to take out the spring?

[yugiohzombielover]

finally i removed all the restrictors in the shel OH SHIT!! where did it go?!?!

[wolfpupfluff]

you just basically gutted the son of a bitch...

[craigrbrown]

Yea I don't know if anyone will respond but could I get some clarity on some things.

First you said, 5/16th bit, but you said don't damage the lip (the bit doesn't slide right in is that what's supposed to happen or no). Also the hole itself is 3/16th so how does that make sense, I used a 9/64th to get the post out.

I can't get access to the spring, is this because of my bit? Does the bit cut through the plastic allowing access to the spring?

Is there an easier way to get the plastic out?

[stingwirezification]

what i did with the shell is rebarrel it with cpvc and glued the black piece inside of the shell.

[stingwirezification]

i saw a thread on nerfhaven from you doing the mod

[Ryno69ification]

with the old shells u don't have to do all that crap

[TheDeadlysting]

so it's about 45 minutes per 10 shells abortioned. . .hmm. . .maybe i'll stick to gun modding instead

[the4bros1]

sodemizing iro lol

[phetdart]

get a hammer with a nail bang hard take out the spring and the green circle part put the orange part back

[McGiggitygoo]

so basically you just aborted the shell's baby

[autonerf]

@McGiggitygoo lol

[TheDeadlysting]

@McGiggitygoo lolol no offence to be correcting you, but it's abortioned not aborted

[toxiczombieattack]

@TheDeadlysting Nu uh? D:

[Imtheguywiththenerf]

@McGiggitygoo haha



[dansshannon]

@McGiggitygoo dos the double barrle take same shells as the rifle

[emorocker987]

@dansshannon yeah

[OMFGWTFSTFULOL]

I got everything out using a drill, I only drilled in the small circle, shoots just like a normal shell. The only thing I see that's different is the dart falls out when you tilt it over too much.

[pat0dog]

All that work for one shell? Surely theres an easier way.

Nice vid though.

[mylvl200wizardpwnsjk]

@pat0dog he was just too careful

[phetdart]

@pat0dog get a hammer with a nail bang hard take out the spring and the green circle part put the orange part back

[Venom41400]

lol at 3:28, will that work with the Australian buzz bee shells

[Thezeronumber]

Never knew there were springs in the shells...

[LeGoBoY2235]

@Thezeronumber ya same here...

[inuyasha3436]

1st viewer