PART 7 DUAL PERMANENT MAGNET ROTOR AXIAL FLUX WIND TURBINE

[FreePizza007]

What heppens when the wind speed hists 88 MPH does the Axial Flux create 1.21 Gigawatts?

[hifeyracer]

click...click...click...click lol

[TheGodlessGuitarist]

get an alternator from the scrap yard! Will save you a lot of time, effort and expense.

[muddymuddymuddmann]

@TheGodlessGuitarist YA THAT'S OK IF YOU CAN SPIN IT 700 + RPMS ALL THE TIME. AND DONY USE POWER FROM THE BATTERY TO POWER THE FIELD WINDINGS. THE REGULAR CAR ALTERNATOR IS THE MOST INEFFICIENT ONE THERE IS BECAUSE AUTO MANUFACTURERS THINK YOU DONT CARE ABOUT MAKING 5% ELECTRICITY WITH 1/3rd OF YOUR HORSEPOWER AVERAGE. A SOLAR PANEL ON THE ROOF OF YOUR CAR WILL GET YOU 35% MORE GAS MILAGE. IMAGINE THAT.

THE AXIAL FLUX ALTERNATOR STARTS CHARGING AT 100 TO 120 RPMS EASILY WITH VERY LITTLE LOSSES.

[TheGodlessGuitarist]

@muddymuddymuddmann

Didn't realise they were that inefficient :o|

What about washing machine motors?

[muddymuddymuddmann]

@TheGodlessGuitarist IF YOU TAKE THE ARMATURE OUT AND LATHE A GAP FOR CURVED PERMANENT MAGNETS IN IT. AND EPOXY THEM IN, IT WILL PRODUCE NICELY. THE SAME WITH THE AUTO ALTERNATOR. BUT THE STEEL LAMINANTS IN THE STATER COILS WILL TAKE 35% OF YOUR EFFICIENCY AWAY THROUGH EDDY CURRENTS, LENS CURRENTS, AND START UP COGGING. BUT THEY WILL WORK MUCH BETTER THAN AN ALTERNATOR THAT USES THE BATTERY TO MAKE THE MAGNETISM TO MAKE MORE ELECTRICITY. REMEMBER CAR MAKERS ARE PART OF THE BIG OIL GAME.

MUDDy

[TheGodlessGuitarist]

@muddymuddymuddmann many thanks for the info :o)

[muddymuddymuddmann]

@TheGodlessGuitarist ANYTIME.

MUDDy

[matthew18452]

How do you decide on what  thickness of wire to use?

[muddymuddymuddmann]

@matthew18452 THERE ARE 3 WAYS THAT STAND OUT. 1) USE ANOTHERS PROVEN WORK AS A TEMPLATE. 2) DO A MESS OF FORMULAS OR A PROGRAM THAT ASKS A LOT OF MEASUREMENTS AND FACTORS THAT TAKE A MONTH TO LEARN IN CLASSES. OR 3) DRAW THE PARAMETERS FOR THE COIL TO FIT INTO, SUCH AS THICKNESS AND WIDTH AND SHAPE. FIT AS MANY WINDINGS AS YOU CAN FIT NTO IT. THEN TEST IT IN BETWEEN THE ROTORS AS THEY SPIN A CERTAIN RPM. THIS TEST COIL WILL TELL YOU HOW MUCH VOLTAGE ONE COIL WILL MAKE. CONTINUED TO NEXT PART...

[muddymuddymuddmann]

@matthew18452 PART 2 - CONTINUATION OF PART 1......

THEN MULTIPLY BY HOW MANY COILS YOU WILL HAVE IN THAT PHASE. THEN IF YOU WIRE IN STAR CONFIGURATION, JUST MULTIPLY THE TOTAL VOLTAGE OF ONE PHASE TIMES 2 AND THEN AGAIN BY .707 TO GET THE APROXIMATE VOLTAGE AT THE DESIRED RPM. IF YOU KNOW THE SIZE OF THE PROP YOU WILL HAVE, AND THE TIP SPEED RATIO, YOU WILL KNOW HOW MANY RPMs YOU WILL HAVE IN THE DESIRED START UP WIND. IF THE WIND TURBINE STALLS, JUST SPREAD HE ROTORS A BIT FARTHER APART.

[muddymuddymuddmann]

@ToorWind THANKS! I WILL CONCIDER IT. SEND ME P. M. MAIL. I WILL COPY THE EMAIL ADDRESS FOR WHEN I HAVE TIME TO TALK. FOR NOW I WILL FINISH THIS ONE FOR TESTING AND USE. THEN I WILL CONNECT WITH YOU.

MUDDy

[Losenger]

Perfect wound coils are pretty, but unnecessary in this application. 

[muddymuddymuddmann]

@Losenger PRETTY IS PRETTIER THOUGH, AND TIGHTER. THESE BARELY FIT THE CIRCLE. I NOTICED THAT 2 OF THE COILS WENT OUTSIDE THE SECTORED PIE SHAPE, BUT I HAD 3 COILS THAT WERE REAL TIGHT. THAT ENABLED ME TO ARRANGE THE ORDER TO FIT THEM IN NICELY. IT ONLY TOOK 2 TRIES. AND I WAS GLAD TOO.

MUDDy

[shortyjk95]

where did you get the wire from???

[muddymuddymuddmann]

@shortyjk95 APPLIED MAGNETS. TYPE IN MAGNETS4LESS . THEY ARE LOCATED IN PLANO TEXAS.

[storkfmny]

Nice guitar work.

[muddymuddymuddmann]

@storkfmny THANKS! IT DOES HELP TO FREE ALL THE BUNDLED UP BUNGLES FROM INSIDE. FEELING THE ENERGY FLOW OUTWARD SEEMS TO BRING IN GOOD ENERGY. TO ME IT'S AS USEFUL AS A GOOD NIGHTS SLEEP, OR MEDITATION.

MUDDy

[20RoyalSuperKing]

What gauge is that Muddy?

[muddymuddymuddmann]

@20RoyalSuperKing 14 GAGE AWG DOUBLE INSULATED HIGH TEMP ENAMEL WIRE. 77 TURNS FOR A 24 VOLT MACHINE.

MUDDy

[JOHNNYH8STHENWO]

I almost missed this. It's too bad you couldn't mass manufacture these. You could get an assembly line going.

[muddymuddymuddmann]

@JOHNNYH8STHENWO I PLAN ON DOING THIS FOR A LIVING LATER ON, AND SERVICING THEM.

MUDDy

[virlusun]

yes she can weld...it is the same as using a glue gun...but much...much hotter. I learn to weld tin for my cookies and cakes molds. I am going to get the plan for curcible furnance just like baking a cake. we can make nice earings out of aluminium. ji,ji,ji :)

[muddymuddymuddmann]

@virlusun SHE WILL WELD SOON ENOUGH, BUT THE WELDER I HAVE GIVES ME A LOT OF TROUBLE GETTING THE ARC TO START WITHOUT STICKING. A LITTLE BETTER WELDER WILL MAKE IT AS EASY AS IT SHOULD BE. AND MORE FUN. BUT SHE DID SAY SHE WOULD WIND COILS.WWWEEEEE!

MUDDy

[virlusun]

sorry got new phone android...i know one thing once she reailze people will like her just the way she is she will be more comfident in the audience. I have something to be ashame...my accent and people still like me bc who I am. My presentations skills improved tremendously since I ve been posting videos...it takes time and practice. we want to see your wife....

[muddymuddymuddmann]

@virlusun HA HA! SHE IS LAUGHING NOW. BUT I WILL GET HER ON THE CAMERA. SHE SAID SHE WOULD CARVE A PROP AND DO ONE OF THE CEILING FAN CONVERSIONS. LOL. NEXT SHE WILL BE WELDING LIKE YOU. UH OH... SHE SAYS SHE CANT WELD. LOL. NOT YET ANYWAY. THANKS FOR THE COMMENT... NOW I HAVE A NEW SUBJECT TO PICK ON HER WITH.

MUDDy

[virlusun]

TheBest

[muddymuddymuddmann]

@virlusun THANKS.

MUDDy

[jwwm2]

@ 2 questions: 1) If I was a little sloppy winding coils, would it make a big difference as long as it all fit properly into the stator? 2) Your wife has a nice voice, will we see her in a video? If it's good enough for Dan Rojas it ought to be good enough for MUDDy. My wife would never agree to it, though....

[muddymuddymuddmann]

@jwwm2 MY WIFE IS SMILING. LOL. I SNUCK HER INTO ONE OF MY VIDEOS ONCE. SHE TRIED TO HIDE FROM THE CAMERA WHILE LAUGHING THE WHOLE TIME. I'LL GET HER IN HERE AGAIN, TRUST ME. AND SHE KNOWS IT. WWEEE!

SLOP IN THE COILS MEANS MORE AIR, OR LESS WINDINGS IN THE SPACE ALLOTTED. A SLOPPY COIL WILL DROP POWER ABOUT 3%. BUT THE CURRENT WILL DROP AS WELL. SO WHEN THE CURRENT DROPS, THE ALTERNATOR SPINS EASIER. THUS THE BLADES WILL SPIN FASTER MAKING UP FOR THE LOSS. SO NOT MUCH, JUST HIGHER RPM.

MUDDy

[hydrophoenixx]

Muddy, can you use any copper wire or does the copper wire need to have a coating of resin?

[muddymuddymuddmann]

@hydrophoenixx ENAMEL WIRE IS USED BECAUSE THE INSULATION IS TOUGH AND VERY THIN. PLUS IT IS A VERY GOOD INSULATOR. BEING THIN AS IT IS, YOU CAN PACK MORE WINDINGS IN A SMALL AREA. MORE WINDINGS MEANS MORE COLLECTION OF THE CHANGING MAGNETIC FLUX. JIM FROM THE VIDEO...OFF GRID - FORCED TO BE GREEN...REWOUND HIS ALTERNATORS WITH CAT-5 CABLE. HE DEPENDS ON 2 OF THESE AND HIS SOLAR CELLS. ALTHOUGH HE IS HAPPY WITH FREE LOW POWER, HE COULD GET 40 TO 50% MORE. ENAMEL WIRE HANDLES MORE HEAT.

MUDDy

[doug2877]

U DA MAN,,,Later From The West Coast,,,:P

[muddymuddymuddmann]

@doug2877 DOUG DOUG! SUPER GLAD TO HEAR FROM YA. THANKS FOR THE DROP BY. KEEP SMILING AND KEEP THE FAITH.

MUDDy

[virlusun]

paciencia!

[muddymuddymuddmann]

@virlusun PATIENCE IS EASY IF YOU ENJOY IT. THANKS. ALL DAY WHILE I AM AT WORK, I WANT TO GET HOME AND WIND ANOTHER COIL. LOL. 5 MORE TO GO NOW. THEY SHOULD GO PRETTY FAST OFF CAMERA.

MUDDy

[virlusun]

God bless your pacien

[muddymuddymuddmann]

@virlusun THANKS E.

MUDDy

[CaptBart]

What's the wire gauge you used here?

[muddymuddymuddmann]

@CaptBart DOUBLE INSULATED 14 GAGE ENAMEL WIRE.

HIGH HEAT.

77 TURNS FOR 9 FOOT PROP AND 24 VOLT OUTPUT. OR USE 2 STRANDS WITH 36 TURNS FOR 12 VOLT. OR 140 TURNS OD 18 GAGE FOR 48 VOLTS. THIS ONE IS 24 VOLT SYSTEM. THE DISKS ARE 11 INCHES. MAGNETS WILL BE 2 INCH X 1 INCH X 1/2 INCH N-42 GRADE NEODYMIUM IRON BORON MAGNETS. THE PROP WILL BE PINE.

MUDDy

[CaptBart]

@muddymuddymuddmann Kewl, Thanks!

[muddymuddymuddmann]

@CaptBart WWWEEE! ANYTIME.

MUDDy

[SurvivalWithBushcraf]

@WambliPeta There are plenty of bushcraft video in a playlist or two on my channel. Wild edible's bushcraft skills.... Check through my playlists. Some good stuff in there....  Survival... With bushcraft in an economic collapse... And it is only bushcraf, because the channel name was to big and I could not fit the "T" at the end.

love and light,

sylvia~

[WambliPeta]

@SurvivalWithBushcraf Thanx for clearing that up 8-)

Btw I also say Love and Light 8-) Nice to meet you Sylvia

[SurvivalWithBushcraf]

@WambliPeta There are plenty of bushcraft video in a playlist or two on my channel. Wild edible's bushcraft skills.... Check through my playlists. Some good stuff in there.... Survival... With bushcraft in an economic collapse...

[WambliPeta]

@SurvivalWithBushcraf Yep I found them. Checking them out and Subbed ya 8-)

[muddymuddymuddmann]

@WambliPeta SYLVIA IS PRETTY COOL. I CHECK HER CHANNEL OUT FOR MY NEWS THAT YOU DONT GET ON TV. VERY INFORMATIVE. THE COOL THING IS GOOD INFORMATION AND OR OPINION LEADS TO A WIDER SCOPE OF THINGS TO CONCIDER WHEN TRYING TO DOPE OUT WHAT'S REAL AND NOT. MISSING INFO DOESNT GIVE THE OPTION.

GOOD TO SEE YOU SEARCH OUT THE DETAILS IN MY VIDS TOO. KEEP THAT EAGLE EYE ON THE SHARPENED FOCUS. PEACE BRO.

MUDDy

[mybigtokachi]

I like your vids because you don't over edit them. We get to see the full process - warts and all - and get to learn from your mis-steps. Very educational.

[muddymuddymuddmann]

@mybigtokachi THANK YOU. I APPRECIATE THAT VERY MUCH. WHEN I EDIT, I EDIT FOR TIME. AND SOMETIMES FOR THE EXPERIENCE GAINED BY DOING SO. MISTAKES ARE DETAILS LEARNED FROM. NOT TO BE DISREGUARDED. HOPEFULLY MY VIEWERS WONT HAVE TO MAKE THE SAME MISTAKES AND GET THE EXPERIENCE AS WELL. THAT'S WORTH ALOT. JUST LIKE.... NO MATTER HOW MUCH JELLO YOU PUT IN A SWIMMING POOL ,,, YOU STILL CANT WALK ON WATER.

MUDDy

[WambliPeta]

Btw using the drill press as a tensioner...... NICE 8-)

[muddymuddymuddmann]

@WambliPeta IT WAS THERE AND I KNEW IT WOULDNT BUDGE. HANDIER THAN I THOUGHT WHEN I FIGURED I COULD INCREASE TENSION TO THE PULL I NEEDED. MY RM WAS TIRED AFTER 2 COILS. IT WORKED GREAT. THANKS FOR THE COMPLIMENT,

MUDDy

[WambliPeta]

I'm gonna guess that at least 50 to 75% of the time making these coils was in making the jig for winding, but the pay off is every coil will go faster and smoother. I think that's why I like your vids..Your ability to make jigs and rigs to speed up the process.....Btw If I were a bett'n man, I would bet you lost count around 8:48 "click" ;-)

Teamwork FTW 8-)

[muddymuddymuddmann]

@WambliPeta I EDITED SOME OF THE VIDEO OUT, AND IT MADE A FEW GLITCHES IN THE COUNT ON VIDEO. I WASNT COUNTING MUCH. THAT'S WHY I GOT MY SWEETY TO DO IT FOR ME. SHE HAS A REAL GOOD ATTENTION SPAN. ME... I'M SCATTER BRAINED. I CAME ACROSS PART OF THE VIDEO WHERE I THOUGHT I HEARD 2 CLICK IN ONE ROTATION. SO YOU WHERE PROBABLY RIGHT. SOME SAY IT WILL NOT WORK, BUT I HAVE MADE A LITTLE SERIES COILED ALTERNATOR WITH ODD BALL COILS. IT WORKED NICE. 1 WINDING IS LIKE 1.2%. GIVE OR TAKE.

MUDDy

[SurvivalWithBushcraf]

Yay! I got the first thumbs up!

[muddymuddymuddmann]

@SurvivalWithBushcraf HA HA THANKS, I AM EDITING THE NEXT PART NOW. IT SHOULD BE READY FOR UPOAD IN AN HOUR. THEN THERE IS EVEN MORE VIDEO TO EDIT. I'M LOVING IT.

DEFINITELY A HAPPY MUDDy DAY:)

MUDDy