Reptile Room Update / New Snake Rack

[rallisonreptiles]

just spend the mony and buy u an animal plastics rack

[Skaterman1408]

why dont u fill in the whole tub of aspin man poor snake nigga cmon

[Skaterman1408]

u should try stick a peace cardboard to make it come out better

[machoev12]

you should just put vertical pieces that go in the middle it will fix the bow problem

[702justin702]

melamine is awsome to make cages and racks. ive built them for years using it.

[SnakeKeeper2010]

when you were building the rack you should have made the top rest on the sides not bolt thur the side into the top.

[johnythanj]

how do you get the little newtek thermostat to work? mine has the red light on and it doesnt heat up the hot spot to the right temp

[jeffevens13]

@johnythanj the fuse might be shot, that happend to one of mine, i had to just get a new one. just make sure you dont plug in more watts than it can handle. like for example mine can only handle 1000 watts so i cant plug in much more than my little heater

[soapbubble6]

just my opinion...

[soapbubble6]

Hey I think that boxes are ok for the regius, but don't you think they're a litttle bit wrong for corn snakes or anacondas? Corn snakes want to climb and anacondas need water to swim in. I think it's not ok to keep them in boxes and neither the boa.

[CalxBilko]

yh cool reptiles but where is all the UV lighting, heat lamps, hiyds u should not keep them in bloody food tubs!

[DairIk22]

@CalxBilko REALLY???? dont comment on stuff if you dont know anything, 1. snakes dont need UV lighting, 2. the heat is from heat tape/heat ropes, not sure what he is using, dont need hides since they are in tubs and the point of hides are to make the feel secure... with they will in a tub... and 4. 1000's of people keep their snakes/reptiles in "bloody food tubs' and its a very good method of keeping reptiles...

thanks!

[ReidHarris7]

sweeeet burm

[killer123051]

in alot of ur vids u say u havn't made a video in a while

[dutrasgeneral]

Very cool. If you use a few supports in the middle of each shelf in the front, you wont get that sagging and your bins will slide better. Dont give up on building your own. Good luck on everything

[reptile4u09]

very cool reptile room i like your vid :)

[danny1023]

I know you said your moving but if you still have this rack you can put up braces in between each shelf. That way you would eliminate the bend in the wood

[elevendaysago]

Ahh, your burmese python is soooo gorgeous~

[qrtqrtqrtqrtqrtqrtqr]

how do you pre your mice

[HerpsnInverts]

where the tight ones are just sand the top of the wood that should help

[b0nzik]

Hey bud you can keep the melamine from sagging by putting a divider/support in the middle.

[jordanrocks2321]

um hello i was wondering if i could have the exact measurements and details on how to make it

[TheScarface4lyf]

hey cool vids .. i was wondering if u would know about my ball python it has a white nose and wondering if it wll go away .i only had it for a month so it hasnt shed for me yet .. do u think it will go away

[An3ggPlant1]

did squidward died YET?

[ISantillan17]

Where did u buy the HELIX..??

[jeffevens13]

from a reptile expo. but i think you can order them from their website.

[cutegayjason]

awesome video update. I think your new rack looks very good. Maybe in time it ill loosen up on those really tight tubs or you could get some half in wooden dowel and wedge it beside the tub to raise it about 1/8 inch and prevent further bending.

[123chinch456]

never mind

[123chinch456]

do you still have your rtbs?

[BallPythonLuver]

Awesome video!! Really cool animals, the burm is getting really big and love her color!

[jeffevens13]

thanks =]

[MrBigmcflyfan]

hey mate good video i love the racks send me aa message on my profile mate it be nice to hear from you  speaK SOON

[jeffevens13]

thanks! alright will do bro. =]

[YAQ91]

Great vid once again man wat can I say u make the best reptile vids on YouTube

[jeffevens13]

aww thanks that really means a lot to me! =]

[grubbadub420]

great vid jeff, i tried makin a rack before and did the same thing half were fine half were to tight, id say after a shed maybe 2 the boa will look fine again 5*

[jeffevens13]

haha i guess we will both just have to buy a rack next time! =P ya thats what i was thinking too. =]

[99pitbulls]

ya some of my tubs in my rack are tight and every time i open and close it the water spills everywhere lol

[jeffevens13]

haha yup just like mine! =P

[BoaC2323]

ya melamine is great all you gotta do is put slits in betweeen the bins. it will correct the bend and make it look good.

5***** nice job bro

[jeffevens13]

thanks =]

[cjcarlosnumber1]

not to put a your building skill down.But a middle partition would have solved the bow in the wood.

[jeffevens13]

haha no offence taken, im not good at building at all! il have to try that if i even want to build a rack again.

[garyfromtheUK]

hi m8 sorry for the 2 comments i didnt watch all of the vid befor a sent last comment, 1 thing i will say about stacking the burm an anacondas is you will find it very hard to get a 15+ snakes out of anything higher than waste height. i made that mistake with the retics. just a thought

[jeffevens13]

no worries! thanks for the heads up! but it will only be 3 cages and they will all be on the ground so the top one will be no higher than 4 and a half feet high, and i could put like the smaller male in the top one. =]

[garyfromtheUK]

why dont you make them a little loser fit not so much so the snake can get out just a 1 mm gap at the top and put a bar down the front to stop them pushing the tubs out, saves busting a gut everytime you want a snake out

[jeffevens13]

i did do that but the wood bends and bows so if its 1 mm gap at one part it would be a half inch gap at another...

[suzadurai1]

hey man just some dividers and slide them in the center of each shelf and it should be perfect cuz i have an 8 foot long rack and it works really well

[jeffevens13]

ya i did that with the top shelf but if i do that with the other ones then it just makes the other shelfs around it tighter. lol

[ISantillan17]

Nice vid. Can you do an update on your spider ball python wen u get the chance?

[jeffevens13]

thanks. ya for sure. =]

[An3ggPlant1]

Im pretty sure he died

[FTWreptiles]

wow jeff,nice reptile room. and you get sick alot. maybe you should use vitamin c tablets or something. lol

[jeffevens13]

ya ive been getting sick alot even since i got mono... lol ya ya my grandma makes me take those! haha they taste sooo gross! D=

[FTWreptiles]

lol i take them too, and yes they do

[leopardgecs22]

do you still have your monitor

[jeffevens13]

no i dont have him any more.

[An3ggPlant1]

did squidward die?

[jeffevens13]

idk hahaha i think he is still at the petting zoo! =P

[octavian300]

Sick stuff jeff, You ready for pasadena show?! i'm so stoked to see everyone again. You just need to STAY LONGER this time haha.

[jeffevens13]

thanks Cam! hell ya , cant wait! and ya i should be staying all day this time! =D haha

[fatfrogz]

I like your hair! How much did the pied cost you? If you dont mind me asking?

[jeffevens13]

thanks, i cut it myself! =] she was $1,200

[fatfrogz]

Thats what I thought, I love pieds as a morph but I dont have that kind of cash. :(

[jeffevens13]

dont worry the prices on ball pythons drop really fast! like last year they were selling for over $2,000

[XxXsnakecharmerXxX]

how much did it cost?

[jeffevens13]

if your talking about the rack, i think less then $50 (not including the tools needed to make it) =]

[XxXsnakecharmerXxX]

for all the melamine!?!?!

[jeffevens13]

ya its expensive! i think it was like $24 for one 8'X4' sheet. but i could be wrong...i actually built it along time ago, i just havent gotten around to making a video till just now! haha =P

[XxXsnakecharmerXxX]

what are the ble prints ,like what are the dimensions for each board i suppose

[jeffevens13]

im not even sure! haha i just kinda set the tubs on the wood and marked it with a pen and then used that piece of wood to trace the lines for all the other pieces. as for the sides i first stacked all the tubs and shelfs with nothing holding them together and then just stood up a piece of wood next to it and marked it with the pen to cut it to the right size. after all that all i had to do was screw it all together. =] lol

[kamptraining]

I was wondering how the night drop works on your helix. I got a used one and it didn't come with directions. Thanks!

[jeffevens13]

ok the night time drop works by setting the helix to the temp you want it to drop to, then plug in the night time drop attachment, then unplug the night time drop attachment from the outlet only (not from the helix), then while its unplugged set the helix to the day time temp, now all you have to do is plug the night time drop attachment into a timer so that it will turn it off in the day time. =] i hope that made sense, if you want i could make a video as soon as i get mine fixed. =]

[jcshanks]

Put a can of vegetables on the top rack to give you just a bit more space to slide the tubs. BTW, what beeps non stop when you make videos? A smoke detector needing a new battery? Peace out! J

[jeffevens13]

i did that with a piece of wood but i cant make it to big because it pushes down on the other shelfs make them tighter. lol and ya its a smoke detector... haha =P

[An3ggPlant1]

so thats what kept waking me and matthew up

[jeffevens13]

well what the heck are you and matt doing sleeping in my reptile room!?!?! 0.o

[An3ggPlant1]

no we heard it from the living room,

I thought it was jessica being raped

[jeffevens13]

hahaha wtf?!?!?! how does that sound anything like Jessica being raped!?!? not that i would know.... hahah =P