Man dude i installed all of it but iu got a male Y thing. U said u think its Female i think it is too. Going to radio shake tomorrow to buy the new one. Hope it works. Got a video where it shows what it does and its still all hooked up.
When u cut one end off the male to male 3.5mm jack, there was a white,red, and yellow wire. Where does each wire go in accordance to the positive and negative speaker wire coming from your PA speaker?
@AAATACOMAN - sounds like a stereo wire to me. You need a mono, it will only have 2 connections. One in a thick rubber housing(+), and one thats normal(-).
Hey man i got everything. But instead of useing the CB watt i bought a 100 watt amp. I was wanting to know how to hook up the Cb to the amp then the amp to the Speaker.. Well the last part isnt that hard but how should i hook up the CB to the Amp so i can get it really loud.
@TriangleSandwiches Hey man i think i figered it out. This friday i will have all the Parts. Well just need the amp now. The whole thing cost me $160. I will put up a video on how to do it and what to buy. took me a day to figer this all out but i got it down. Soon i will have 100 watts PA system instead of 4-15 watts. i dont remember how many watts the Cb radio puts out.
Brah I just installed the same 100 watt speaker from radio shack, Did almost everything you did except ran the power to the battery, and mounted the speaker near the spare tire. The speaker is ridiculously loud, thanks great video.
@TriangleSandwiches i know. i dont mean wire it to a fuse, wire it to the fuse box to a fuse, take out the fuse in a fuse box, shove the wire in the terminal and put the fuse back in, it has power and when the trucks off, it it will turn off
@xXShadowRejectsXx - Yea you can run it to an accessory fuse, but it barely pulls any power. Shouldn't notice any power loss if you forget to turn it off.
@superg00nsquad - not sure about that. Try using a stereo 3.5mm wire instead of mono, and plugging into a line out source on the head unit or audio player.
It will play, but will be pretty quiet. You'd have to run an amplifier through it I'm sure.
@thephonekiller - Point down towards the ground so it resonates off at all angles, or just mount the speaker point outwards in an open area. Check connections and make sure cord is MONO. Check voltage with a voltmeter to see if you are getting a full ~12v to the CB. And if you can solder the connections to ensure the best conductivity.
i got it working today i was pretty suprised how loud it was. its a good thing you told me it had to be mono because i was about to make my power horn into a grill speaker.
@TriangleSandwiches i m sorry to sound like a dick i have worked on this for a few hours now and i cant seem to power the power horn i have. i dont understand does it have to be a spliced 3.5mm wire or a regular one that i use for my ipod.
@The1911aMansGun - no worries. The black and white wires that run off the powerhorn need to connect to a wire in which has a 3.5mm male end(connects into CB). The other side of the 3.5mm wire needs to be cut. Now the wire NEEDS TO BE MONO. Stereo will not work. Sorry if I did not clarify. So the ipod wire will not work. Radioshack sells MONO wires that are 3.5mm. Once you cut off one of the male ends, strip back the wires and twist or solder them to the wires off the powerhorn.
@TriangleSandwiches alright thanks i thought it would work with the ipod wire but know that i know i will check it out thanks man. im putting it im my dads old nissan titan he gave to me after i got my farm permit.
Just an FYI do not try to only hook up a PA system to older cb radios. If you supply power to the cb without it being connected to a cb antenna it will fry the radio! It is perfectly ok with newer models. For sure do not try with any 23 channel ones and i would be weary with ones before 1995
i have a question about the actual cb radio, i was looking around and heard some good things and some bad things about this radio. so is it a good radio or not.
@ L33t- just run wires an mount to your frame. It doesnt need to be next to the battery.
I doubt they sell a CB radio with sirens on them. I know they sell little amps that have the PA function and many sirens and animal noises(like ice cream trucks) but with no CB SETTING.
If your CB has no antenna you will not get a signal at all, and it's supposedly bad for the radio to be switched into CB mode without an antenna.
@TriangleSandwiches Thanks for the help. I've decided to wait until I get a new car (in about 3-4 months) to do it - my current one has no good spot to run the wires. No hole in the firewall, and no way to run it to the trunk without modding the vehicle.
My car has the battery and fuse box at the back. How well do you think it would broadcast with the PA speaker mounted in the trunk? Also, do you know of any CB radio that has the PA function and a couple siren sounds built in? I'd like to be able to play a siren over the PA occasionally for events and stuff. I'd buy a plain PA with siren, but I also want the CB radio. Last but not least, what's the range like on a CB radio with no antenna?
@troyatl68 - yea if ur caught using the PA. but the CB radio isn't. when i didnt have an antenna and i got pulled over the cop questioned me about it.
I have the same radio and just installed a PA. Mine is a touch quiet, I want to devise a small amplifier for it inline with the main cord to the speaker.
how much noise is there from accelerating when you plug your pos./neg. into the cigarrette lighter. ive got my pluged into my fusebox. i also have a little 1 foot dildo whip but am getting 4 ft dual whips soon. what antenna do you got?
@TriangleSandwiches Yeah. I bought 2 whips and a dual cord and a single cord. I tested it out with a friend from 7 miles away and the duals had the better reception and had range of 10+ miles. They are 4 footers and there is no background noise from the engine.
nice man. i am putting it in my jeep grand cherokee. When I put it in the accessory fuse box part do I have to worry about anything? Will it drain my battery?
@The415guy - no it pulls barely any power whatsoever when on and not in use. If you are very concerned about it draining anything, just turn it off when not in use.
Yet usually when u plug into an accessory fuse, you dont have to worry about forgetting to turn it off as it will by itself when the key is out of the ignition.
@The415guy hey i have a jeep grand cherokee and it is an 98 and i put it under the bumper on the right side and it fits great i have no battery problems and i have it hooked up to the fuze box it has constant power and no problem hope this helped.
@bigislife nice. i want a 1998 grand cherokee. i have a 2010 grand cherokee and put it under the bumber as well and it is awesome. People can hear it real well. I did not hook it up to the fuse box. I hooked one cable up to the battery and ran a doublesided cable through the drivers door side and around the engine. I will probably be making a video of the set up sometime soon.
@The415guy well i hope i helped as much as i could lol i am geting a new cb today or the next so yea i will put up a video of that man sub to my channel and check it out bro.
@BowHunterAz08 - its fine as long as its in PA mode. most people doing this tut only want the CB for the PA usage and don't care about the CB capabilities.
I also mentioned it in the video on a text box i beleive
@TheJammedToilet - its not in the engine compartment at all, but as long as its away from moving parts ur fine.. just dont mount it anywhere near a fan or belt and ur fine lol
and no its completely weatherproof. ive submerged it completely in water and mud while offroading and it works like new.
@CCSinventions wow your cool. you probably sit at home jack off to pictures of your mom, then fuck a FAT stripper. after that you come home and look at gay porn.
@crf250x33 - I am in the process of trying to figure out how to do this. I will post a video how once I figurethat out I promise.
IF SOMEONE KNOWS HOW TO WIRE THE CB TO AN AMP AND BE ABLE TO REALLY POWER THE SPEAKER TO IT'S POTENTIAL, LET ME KNOW AND I WILL MAKE A VID AND GIVE YOU A SHOUT OUT.
@vidkid- headphones should be fine. Just cut off the earbuds and run one wire to positive and one to negative. If the sound doesn't work switch the pos and neg. I think it should work fine. That's a good idea
i have the exact same set up as you except i sawed off my cone for space purposes. my sound isnt as loud as others are with the same speaker and i was wondering if routing extra power from the cigarette adapter to the speaker (bypassing the cb) would increase the volume more. would this work?
@jsanc- that's where I got mine.. But I'd like to recommend to not go that route. Wire the red directly to your positive and the black to any bolt you can find a good ground. Not only is it cleaner but it will get more power.
@ajd- I had the Same problem with size! Just cut the big ass plastic cone surrounding the speaker(just not the middle cylindrical piece). And take off the spring and mount so the metal circle piece is attached to the speaker only. Then find a bolt on you chasie or bumper and tighten in down through the hole.. I'll make another better video soon lol
@TriangleSandwiches holy shit, that is a genius idea, this that previous comment i now have my cb fully operational but am waiting for friends to get them so i might get the speaker this weekend
Where did you get that lighter adapter? I can't find it anywhere! The people in Radio Shack looked at me like I had two heads when I asked for one....lol
I am building an ice cream truck and was wondering if you can play music through your PA system. I could purchase a Music Truck PA System for about $200 which is way to much for my budget. I do have a CB/PA in my Van but was wondering how I could hook up a IPOD to it or some other recorded gadget. Thanks.
i have the exact same cb with the antenna and same exact speaker on my mustang gt but u gotta make sure water doesnt puddle in the horn or itll stop working this happened to me when i had it faced up. it stopped working with the water but when i took the water out it worked like new again. so if u want it faced up just make sure its not gonna get water in it
Do you need an amp
471drummer 2 days ago
@471drummer - no
TriangleSandwiches 17 hours ago
i frigin love this video... nice job haha
WeirFurthur 5 days ago
Man dude i installed all of it but iu got a male Y thing. U said u think its Female i think it is too. Going to radio shake tomorrow to buy the new one. Hope it works. Got a video where it shows what it does and its still all hooked up.
BadMonkeyBallz 1 week ago
When u cut one end off the male to male 3.5mm jack, there was a white,red, and yellow wire. Where does each wire go in accordance to the positive and negative speaker wire coming from your PA speaker?
AAATACOMAN 1 week ago
@AAATACOMAN - sounds like a stereo wire to me. You need a mono, it will only have 2 connections. One in a thick rubber housing(+), and one thats normal(-).
TriangleSandwiches 1 week ago
Hey man i got everything. But instead of useing the CB watt i bought a 100 watt amp. I was wanting to know how to hook up the Cb to the amp then the amp to the Speaker.. Well the last part isnt that hard but how should i hook up the CB to the Amp so i can get it really loud.
BadMonkeyBallz 1 week ago
@BadMonkeyBallz - Thats one thing i've always wanted to do, just never got around to it. I'm not sure exactly, i'd have to see it.
TriangleSandwiches 1 week ago
@TriangleSandwiches Hey man i think i figered it out. This friday i will have all the Parts. Well just need the amp now. The whole thing cost me $160. I will put up a video on how to do it and what to buy. took me a day to figer this all out but i got it down. Soon i will have 100 watts PA system instead of 4-15 watts. i dont remember how many watts the Cb radio puts out.
BadMonkeyBallz 1 week ago
@TriangleSandwiches Ill put up a video of yall reading my idea. Hope you can read my hand writting. But Friday i will have it all hopfully.
BadMonkeyBallz 1 week ago
@TriangleSandwiches got to my channle and watch it. Will have new one soon
BadMonkeyBallz 1 week ago
This has been flagged as spam show
Yeah not having a problem with that red wire to the battery, It's nice because i can turn the speaker on without the key in the ignition.
SmallRed525 2 weeks ago in playlist PA
Brah I just installed the same 100 watt speaker from radio shack, Did almost everything you did except ran the power to the battery, and mounted the speaker near the spare tire. The speaker is ridiculously loud, thanks great video.
TheCremoJames 2 weeks ago
@TheCremoJames - glad it worked out.
TriangleSandwiches 2 weeks ago
@TriangleSandwiches itake it the speaker can be hit with water right just asking
beastly789100 1 week ago
@beastly789100 - yea, I've submerged it in mud and water many times and it still worked great
TriangleSandwiches 1 week ago
DO NOT RUN THE RED WIRE TO THE BATTERY! run it to a fuse in the fuse box!
xXShadowRejectsXx 1 month ago
@xXShadowRejectsXx - CB wire already has in-line fuse.
TriangleSandwiches 1 month ago
@TriangleSandwiches i know. i dont mean wire it to a fuse, wire it to the fuse box to a fuse, take out the fuse in a fuse box, shove the wire in the terminal and put the fuse back in, it has power and when the trucks off, it it will turn off
xXShadowRejectsXx 1 month ago
@xXShadowRejectsXx - Yea you can run it to an accessory fuse, but it barely pulls any power. Shouldn't notice any power loss if you forget to turn it off.
TriangleSandwiches 1 month ago
@TriangleSandwiches yea lol
xXShadowRejectsXx 1 month ago
is it illegal to have a cb in your car?
andywray01 1 month ago
@andywray01 - no.
TriangleSandwiches 1 month ago
how do u like the cobra???? i just got it for my jeep is it pretty simple to install?
mizzedikeets 1 month ago
@mizzedikeets - its alright. I like it
TriangleSandwiches 1 month ago
i also have a white taco so this vid was perfect for me haha, thanks bud!!!!
georgiaboy353 1 month ago
when you attach the PA horn the the bare ends, do you keep the bare ends apart from each other? thanks
wbmac1 1 month ago
How would I install the PA wiring, if i wanted to listen to music out of it?
superg00nsquad 1 month ago
@superg00nsquad - not sure about that. Try using a stereo 3.5mm wire instead of mono, and plugging into a line out source on the head unit or audio player.
It will play, but will be pretty quiet. You'd have to run an amplifier through it I'm sure.
TriangleSandwiches 1 month ago
JUST STICK IT IN THE HOLE!!
mattsheedy9 1 month ago
do not key the mic without an antenna on it because that will fuck the cb
chubbyllama7 1 month ago
@chubbyllama7 - Your fine as long as it's in the "PA" setting.
TriangleSandwiches 1 month ago
@chubbyllama7 how does it fuck the CB????
mattsheedy9 1 month ago
mines not that loud, any suggestions?
thephonekiller 1 month ago
@thephonekiller - Point down towards the ground so it resonates off at all angles, or just mount the speaker point outwards in an open area. Check connections and make sure cord is MONO. Check voltage with a voltmeter to see if you are getting a full ~12v to the CB. And if you can solder the connections to ensure the best conductivity.
TriangleSandwiches 1 month ago
Wow!!! Its f#$%& laud!!! ;)
MrTRA504 1 month ago
i got it working today i was pretty suprised how loud it was. its a good thing you told me it had to be mono because i was about to make my power horn into a grill speaker.
The1911aMansGun 1 month ago
@The1911aMansGun - Glad everything worked out.
TriangleSandwiches 1 month ago
Also, does it come with antina ?
Sheqardi 1 month ago
@Sheqardi - no.
TriangleSandwiches 1 month ago
Thank you for sharing this video
Could you please tell me where can I buy the cigarette lighter adaptor? I like this kind of adaptro
Thank you
Sheqardi 1 month ago
@Sheqardi - Radioshack or ebay
TriangleSandwiches 1 month ago
thanks bro
hitman7233 1 month ago
did you get every thing from radioshack bro ??
hitman7233 2 months ago
@hitman7233 - Everything but the CB. Got that from FRYS.
TriangleSandwiches 2 months ago
this is a god damn lie dont waste your money on this ass hole the 3.5mm wire is bull shit.
The1911aMansGun 2 months ago
@The1911aMansGun - Explain.
TriangleSandwiches 2 months ago
@TriangleSandwiches i m sorry to sound like a dick i have worked on this for a few hours now and i cant seem to power the power horn i have. i dont understand does it have to be a spliced 3.5mm wire or a regular one that i use for my ipod.
The1911aMansGun 2 months ago
@The1911aMansGun - no worries. The black and white wires that run off the powerhorn need to connect to a wire in which has a 3.5mm male end(connects into CB). The other side of the 3.5mm wire needs to be cut. Now the wire NEEDS TO BE MONO. Stereo will not work. Sorry if I did not clarify. So the ipod wire will not work. Radioshack sells MONO wires that are 3.5mm. Once you cut off one of the male ends, strip back the wires and twist or solder them to the wires off the powerhorn.
Lmk how it goes.
TriangleSandwiches 2 months ago
@TriangleSandwiches alright thanks i thought it would work with the ipod wire but know that i know i will check it out thanks man. im putting it im my dads old nissan titan he gave to me after i got my farm permit.
The1911aMansGun 1 month ago
If you have it pointing down while mounted to the frame, would water affect it?
vlorraine94 2 months ago
horrible fake accent lol
dubcars101 2 months ago
So is it worth buying the 100w speaker from radioshack if the radio only puts out 4 watts?
or should i just go with a 50w speaker?
x94xPJCx 2 months ago
@adam - no. The cb powers the speaker alone. You can hook an iPod to the speaker and it will play, just not very load.
TriangleSandwiches 2 months ago
did you have to hook up speaker to battery souce cuz my radioshack said it cant power a powered speaker?
adamp1023 2 months ago
where you from mate?
alexsuchapimp 2 months ago
@alexsuchapimp - arkansas
TriangleSandwiches 2 months ago
@TriangleSandwiches you sound english?
alexsuchapimp 2 months ago
@alexsuchapimp - I get that a lot idk why?
TriangleSandwiches 2 months ago
@TriangleSandwiches poser
alexsuchapimp 2 months ago
@alexsuchapimp - Which one?
TriangleSandwiches 2 months ago
Good way ill most likely do it like that
sgtcdz 2 months ago
How would you guys recomend a Midland 1000Z compared to Maxon MCB30 and Citizen CB Radio?
elitecssplayer 3 months ago
Just an FYI do not try to only hook up a PA system to older cb radios. If you supply power to the cb without it being connected to a cb antenna it will fry the radio! It is perfectly ok with newer models. For sure do not try with any 23 channel ones and i would be weary with ones before 1995
BamaBreeze606 3 months ago
@BamaBreeze606 - Thanks man. good to know
TriangleSandwiches 2 months ago
have you thot about mounting ORANGE BECON FLASHER LIGHTS
used on work trucks on the top of your truck.
justicerobbie67 3 months ago
@justicerobbie67 - No, but I have thought about installing a Depth Finder so I know if I am going to hit shore or not.
TriangleSandwiches 3 months ago 2
@TriangleSandwiches
were did you get your cigarette lighter adapter plug.
justicerobbie67 3 months ago
@justicerobbie67 - Radioshack
TriangleSandwiches 2 months ago
Where did you get the cigarette lighter adapter?
jjdoddledoodle 3 months ago
can you turn the volume up and down for the PA SYSTEM?
elitecssplayer 3 months ago
@elitecssplayer - yea
TriangleSandwiches 3 months ago
what the heck is the point of a speaker?
elitecssplayer 3 months ago
@elitecssplayer - oh there is no point it just looks really cool.
TriangleSandwiches 3 months ago
why would you get in trouble if you were pulled over?
elitecssplayer 3 months ago
@elitecssplayer - using a pa is illegal.
TriangleSandwiches 3 months ago
shitty cb radio...
th3kid17 3 months ago
This has been flagged as spam show
can u send me a link to a websight to find a cigarette lighter adapter
thanks.
sportshobby1 4 months ago
I love the accent bro. And awesome PA setup as well.
BloodSeeker117 4 months ago
i have a question about the actual cb radio, i was looking around and heard some good things and some bad things about this radio. so is it a good radio or not.
-Ronan
oolcat1 5 months ago
Hello Dont turn it on without a Antenna!! You will burn it up!! DUH!!! Well too late you ruined it!!!!
coltbuntline 5 months ago
@coltbuntline - Hello, as long as its in PA mode your fine!! DUHH!!!
TriangleSandwiches 5 months ago
I just got a pa system and I love it, but I don't think my parents like it. Either that or they are mad cuz I drove 30min. to get the stuff...
DaBomb1818 5 months ago
@ L33t- just run wires an mount to your frame. It doesnt need to be next to the battery.
I doubt they sell a CB radio with sirens on them. I know they sell little amps that have the PA function and many sirens and animal noises(like ice cream trucks) but with no CB SETTING.
If your CB has no antenna you will not get a signal at all, and it's supposedly bad for the radio to be switched into CB mode without an antenna.
TriangleSandwiches 6 months ago
@TriangleSandwiches Thanks for the help. I've decided to wait until I get a new car (in about 3-4 months) to do it - my current one has no good spot to run the wires. No hole in the firewall, and no way to run it to the trunk without modding the vehicle.
l33tp1mp 6 months ago in playlist l33tp1mp's Favorited Videos
My car has the battery and fuse box at the back. How well do you think it would broadcast with the PA speaker mounted in the trunk? Also, do you know of any CB radio that has the PA function and a couple siren sounds built in? I'd like to be able to play a siren over the PA occasionally for events and stuff. I'd buy a plain PA with siren, but I also want the CB radio. Last but not least, what's the range like on a CB radio with no antenna?
l33tp1mp 6 months ago
Nice video I done mine a little different but it's still in there :). Go check it out
TheTeamdavemade 6 months ago
hide it??? is it illegal?
troyatl68 6 months ago
@troyatl68 - yea if ur caught using the PA. but the CB radio isn't. when i didnt have an antenna and i got pulled over the cop questioned me about it.
TriangleSandwiches 6 months ago
nice truck
TheNBTfilms 6 months ago
this is sick thank you so much
bpschevy4 6 months ago
when you have the white wire for the speaker did you have to cut off the metal thing (that plugs in)
bpschevy4 6 months ago
Urs neighbors are like ( what that fucking moron are doing at this time ) lolol fucking retard..... Do something new u fuck.
TOW4LESS1 7 months ago
Urs neighbors are like ( what that fucking moron are doing at this time ) lolol fucking retard..... Do something new u fuck.
TOW4LESS1 7 months ago
just stick it in the hole.
Nirvanagoon94 7 months ago
nice and snug.
duckanddodge01 7 months ago
I just need to know what wires you plug it in to have it play over the car speakers
rsqizar 7 months ago
i see nothing but dirt mate
STOOPSPBZ 7 months ago
I have the same radio and just installed a PA. Mine is a touch quiet, I want to devise a small amplifier for it inline with the main cord to the speaker.
LeonRFpoa 8 months ago
alright whats up mate
MrPhilclay 8 months ago
its not illegal to have a pa system or cb mounted in your truck dumbass
TheRemington887 8 months ago
Great video. I'm in the process of getting all the things. Can you give me the link for the
adapter?
MrKHuss 8 months ago
how much noise is there from accelerating when you plug your pos./neg. into the cigarrette lighter. ive got my pluged into my fusebox. i also have a little 1 foot dildo whip but am getting 4 ft dual whips soon. what antenna do you got?
Rezolutiionz 8 months ago
@Rezolutiionz - Noise? Just get 1 4 footer or larger if you can. Dual whips is are useless unless they are 8 or 9 feet apart.
TriangleSandwiches 8 months ago
@TriangleSandwiches Yeah. I bought 2 whips and a dual cord and a single cord. I tested it out with a friend from 7 miles away and the duals had the better reception and had range of 10+ miles. They are 4 footers and there is no background noise from the engine.
Rezolutiionz 8 months ago
great work. i am doing the same to my car but what is the 12v cig with the plug things called?????
TheLucasrussell 8 months ago
nice man. i am putting it in my jeep grand cherokee. When I put it in the accessory fuse box part do I have to worry about anything? Will it drain my battery?
The415guy 9 months ago
@The415guy - no it pulls barely any power whatsoever when on and not in use. If you are very concerned about it draining anything, just turn it off when not in use.
Yet usually when u plug into an accessory fuse, you dont have to worry about forgetting to turn it off as it will by itself when the key is out of the ignition.
TriangleSandwiches 9 months ago
@TriangleSandwiches ok thanks. just installed mine with a 25 watt horn. it is louder than expected and its awesome.
The415guy 9 months ago
@TriangleSandwiches how do u kno if its an accessory fuse or a fuse for like you headlights or some shit lik that?
mattsheedy9 8 months ago
@The415guy hey i have a jeep grand cherokee and it is an 98 and i put it under the bumper on the right side and it fits great i have no battery problems and i have it hooked up to the fuze box it has constant power and no problem hope this helped.
bigislife 9 months ago
@bigislife nice. i want a 1998 grand cherokee. i have a 2010 grand cherokee and put it under the bumber as well and it is awesome. People can hear it real well. I did not hook it up to the fuse box. I hooked one cable up to the battery and ran a doublesided cable through the drivers door side and around the engine. I will probably be making a video of the set up sometime soon.
The415guy 9 months ago
@The415guy well i hope i helped as much as i could lol i am geting a new cb today or the next so yea i will put up a video of that man sub to my channel and check it out bro.
bigislife 8 months ago
Excellent, with a few good laughs. Thanks bro
abbeyroad1980 9 months ago
im looking to installing a Cb in my mud truck and was wondering what a decent Cb costs nowa days? and any recomendations??
Dansz71sierra 9 months ago
@Dansz71sierra 30-100 bucks USD go with a cobra 40!
xXxMrWhiteboyxXx 9 months ago
Most annoying accent in the world, and, you know absolutely nothing about wiring or electronics. DISLIKE!
SamTheSuave 9 months ago
@SamTheSuave - KNEW nothing about wiring. Goddamnit, Knew. Past tense.
TriangleSandwiches 9 months ago 4
turn the camera around what the hell
bben95 9 months ago
@bben95 - it was a peanut butter and woodpecker stick.
TriangleSandwiches 9 months ago
Also a good tip for people installing a CB, never power up the radio without it being hooked up to the antenna first
BowHunterAz08 9 months ago
@BowHunterAz08 - its fine as long as its in PA mode. most people doing this tut only want the CB for the PA usage and don't care about the CB capabilities.
I also mentioned it in the video on a text box i beleive
TriangleSandwiches 9 months ago
do you need too hook the power to the speaker too ? or it automatically gets the power from the 3.5 wire u hooked up to your cb ??
Albomafyoz 9 months ago
Comment removed
Albomafyoz 9 months ago
that truck is sick!
MrSuperCargile 10 months ago
I have the same kind.
Zackary747 10 months ago
Thats the same excate kind. do you need a attena. how do you hook up pa?
Zackary747 10 months ago
Nice, but since it's under the hood, can u still hear it clearly when the hood is closed?
Y0B0YCHRIS 10 months ago
@Y0B0YCHRIS - it was muffled. i suggest mounting to the frame so its able to be heard at full potential.
TriangleSandwiches 10 months ago
good video now i know what kinda wires i need to buy
TrapRunner1 10 months ago
Megahorn
TheJammedToilet 10 months ago
Dont you have to worry about damage to the megaborn from your engine? Or weather?
TheJammedToilet 10 months ago
@TheJammedToilet - its not in the engine compartment at all, but as long as its away from moving parts ur fine.. just dont mount it anywhere near a fan or belt and ur fine lol
and no its completely weatherproof. ive submerged it completely in water and mud while offroading and it works like new.
TriangleSandwiches 10 months ago
good vid but just so you know you should never turn your cb on with out having your antenna hooked up it can mess up your radio
greasemonkey21100 11 months ago
@greasemonkey21100 - forgot to not mention that.
TriangleSandwiches 11 months ago
does this cb have a built in antenna?
CCSinventions 11 months ago
@CCSinventions - no, none do.
TriangleSandwiches 11 months ago
@CCSinventions aree you stupid
DjMannyManhart 10 months ago
@DjMannyManhart no I don't know alot about cb dj queer
CCSinventions 10 months ago
@CCSinventions wow your cool. you probably sit at home jack off to pictures of your mom, then fuck a FAT stripper. after that you come home and look at gay porn.
DjMannyManhart 8 months ago
@DjMannyManhart how did u know 0_o
CCSinventions 8 months ago
does it work fine with the cigarette lighter way? even though its the "Ghetto" style lol i liked that
lewisx20x20x20 11 months ago
@lewisx20x20x20 - Yes sir.
TriangleSandwiches 11 months ago
Do you recomend buying an amp for the CB so i can push more then 4 watts out of it into my speaker?
crf250x33 11 months ago
@crf250x33 - I am in the process of trying to figure out how to do this. I will post a video how once I figurethat out I promise.
IF SOMEONE KNOWS HOW TO WIRE THE CB TO AN AMP AND BE ABLE TO REALLY POWER THE SPEAKER TO IT'S POTENTIAL, LET ME KNOW AND I WILL MAKE A VID AND GIVE YOU A SHOUT OUT.
OR MAKE YOUR OWN :)
TriangleSandwiches 11 months ago
is the 100w louder then the 25w if it only gives out for watts
daniel92bustamante1 11 months ago
@daniel92bustamante1 - nope same. you can get a 15w speaker and it'd be just as loud.
TriangleSandwiches 11 months ago
"liked" for saying the iphone is nothing special, good video
travis091491 11 months ago
Haha these goddamned Toyota floor mats same problem with my granny's 03 corolla
HedgehogOutdoors 11 months ago
Nice video, buy why not mount your stuff?
MTLKEBEK 1 year ago
@MTLKEBEK - all nice and mounted now
TriangleSandwiches 11 months ago
@MTLKEBEK i dont know a bunch about cb but how does the whole range thing work? is it if u have a bigger antenna does it get more range or what
QuadKillerSteven 11 months ago
@QuadKillerSteven To get the maximum range of a cb usually you want to be a 3-4' cb antenna. Range im not to sure.
MTLKEBEK 11 months ago
@MTLKEBEK - wrong. the bigger the whip the longer the range period.
TriangleSandwiches 11 months ago
@TriangleSandwiches buy a quality cb antenna and it doesn't need to be that long.
MTLKEBEK 11 months ago
@MTLKEBEK - helps too
TriangleSandwiches 11 months ago
so will you still be able to listen to FM music after hooking this up?
ttstars24 1 year ago
@ttstars24 - Yes....
TriangleSandwiches 1 year ago
@vidkid- headphones should be fine. Just cut off the earbuds and run one wire to positive and one to negative. If the sound doesn't work switch the pos and neg. I think it should work fine. That's a good idea
TriangleSandwiches 1 year ago
@TriangleSandwiches Aright thanks if that doesnt work i got a 3.5 anyways
VidKidd22 1 year ago
Ok I'm using a headphone wire I cut it right below the earbuds should I cut it right before it goes to 2 wires? So it's just one wire?
VidKidd22 1 year ago
where'd you get that cigarette lighter!!??
XionUnjust 1 year ago
Comment removed
VidKidd22 1 year ago
i have the exact same set up as you except i sawed off my cone for space purposes. my sound isnt as loud as others are with the same speaker and i was wondering if routing extra power from the cigarette adapter to the speaker (bypassing the cb) would increase the volume more. would this work?
sibastiNo 1 year ago
Comment removed
VidKidd22 1 year ago
@jsanc- that's where I got mine.. But I'd like to recommend to not go that route. Wire the red directly to your positive and the black to any bolt you can find a good ground. Not only is it cleaner but it will get more power.
TriangleSandwiches 1 year ago
@ajd- I had the Same problem with size! Just cut the big ass plastic cone surrounding the speaker(just not the middle cylindrical piece). And take off the spring and mount so the metal circle piece is attached to the speaker only. Then find a bolt on you chasie or bumper and tighten in down through the hole.. I'll make another better video soon lol
TriangleSandwiches 1 year ago
@TriangleSandwiches holy shit, that is a genius idea, this that previous comment i now have my cb fully operational but am waiting for friends to get them so i might get the speaker this weekend
ajd2466 1 year ago
Where did you get that lighter adapter? I can't find it anywhere! The people in Radio Shack looked at me like I had two heads when I asked for one....lol
Jsanc2075 1 year ago
That's sweet thanks for tutorial I'll be doing this sometime soon.
KT1BZ 1 year ago
I am building an ice cream truck and was wondering if you can play music through your PA system. I could purchase a Music Truck PA System for about $200 which is way to much for my budget. I do have a CB/PA in my Van but was wondering how I could hook up a IPOD to it or some other recorded gadget. Thanks.
HappyEndingsRescue 1 year ago
@HappyEndingsRescue - ive seen ones at Oriellys that have animal noises and stuff.
TriangleSandwiches 1 year ago
i have the exact same cb with the antenna and same exact speaker on my mustang gt but u gotta make sure water doesnt puddle in the horn or itll stop working this happened to me when i had it faced up. it stopped working with the water but when i took the water out it worked like new again. so if u want it faced up just make sure its not gonna get water in it
theboss376 1 year ago