i really believe it is the clip that makwes it jam,. when i first got mine it jammed on every shot,. i took it completely apart and sprayed gunk liquid wrench in all the moving parts,. that made it better but when i started messing around with pliers and the clip feed it made a huge difference!!
the retainer wich is locatated in the back of the gun can be pushed in with a pencil eraser after doing so while still pushing the retainer in lift up on the back of the slide slowly leting it slide of the barrel that should be the way to take it apart make sure its empty with no rounds and safety is off make sure gun has not been fully cocked back putting it back together should be fairly easy
In the very back where you can see the firing pin after you pull the slide back there is a plastic wring looking thing from the back, take a pen push in that plastic looking piece then pull the slide UP from the rear (Not back strait up) and it should come apart, watch out for flying springs though. Do it slowly so you can see how it goes back together and you can find all the parts. First time i did mine every thing flew every where, took me a half hour to find em all.
I have one of these - To tear it down, you push in on the button on the back of the slide (ball point pen works) and you pull back and up on the slide until it comes loose, then remove it off the front. That is it. If its jammed to the point where you cannot move the slide, it probably is not worth your time.
ditto! handles crack and break. problem with that is they are poorly engineered to hold the mechanics together. they break, the gun does not shoot. expensive paper weight though! safer to beat the bad guy over the head with the butt if that is the only weapon you have. either upgrade to a real gun or use the Lorcin as a hammer.
Edit: The slide catch around the firing pin only needs to be pushed in about 1/4". Will pushing it in, pull the slide back about 1/2" and then the back of the slide will lift off from the receiver.
Use a tool to push the catch in the back (around the firing pin) ALL THE WAY IN. At the same time, pull the slide back about 1/2" and lift the back of the slide up. CAUTION: There are lots of little parts on springs that will fly out. Best to do this over a large cookie sheet to catch all the parts. It takes lots of dexterity to put them all back and get the slide and catch back without the parts flying out.
Push in the little circular piece on the back and the slide should pop up. Lorcin pistols suck ass they'll jam everythime you shoot rapidly
chrisbell4900 1 year ago
@chrisbell4900 then dont shoot rapidly
thegod098 7 months ago
i really believe it is the clip that makwes it jam,. when i first got mine it jammed on every shot,. i took it completely apart and sprayed gunk liquid wrench in all the moving parts,. that made it better but when i started messing around with pliers and the clip feed it made a huge difference!!
basskillaz 1 year ago
the retainer wich is locatated in the back of the gun can be pushed in with a pencil eraser after doing so while still pushing the retainer in lift up on the back of the slide slowly leting it slide of the barrel that should be the way to take it apart make sure its empty with no rounds and safety is off make sure gun has not been fully cocked back putting it back together should be fairly easy
602jos 1 year ago
In the very back where you can see the firing pin after you pull the slide back there is a plastic wring looking thing from the back, take a pen push in that plastic looking piece then pull the slide UP from the rear (Not back strait up) and it should come apart, watch out for flying springs though. Do it slowly so you can see how it goes back together and you can find all the parts. First time i did mine every thing flew every where, took me a half hour to find em all.
Brutalnemisis 2 years ago
I have one of these - To tear it down, you push in on the button on the back of the slide (ball point pen works) and you pull back and up on the slide until it comes loose, then remove it off the front. That is it. If its jammed to the point where you cannot move the slide, it probably is not worth your time.
just1pepsi 2 years ago
A L380, dude i had the exact same model of pistol, i swear to God !!!
strazzy3 2 years ago
I wouldn't approve of the .380 you got there. but the p95 is a good choice.
blitzkrieg459 2 years ago
My own humble opinion use it as a paperweight and get a real gun. lol
jackal5382 2 years ago
ditto! handles crack and break. problem with that is they are poorly engineered to hold the mechanics together. they break, the gun does not shoot. expensive paper weight though! safer to beat the bad guy over the head with the butt if that is the only weapon you have. either upgrade to a real gun or use the Lorcin as a hammer.
3ald3eaver 2 years ago
better yet, start a construction job and use it as a hammer. you'd get better ROI
3ald3eaver 2 years ago
Can u make a video of u taken it apart cuz i cant thank u
bxbabyface20 3 years ago
push the black peace thats in the bottom of the trigger. pull it back and up.and it should com apart
lapsley2407 2 years ago
Edit: The slide catch around the firing pin only needs to be pushed in about 1/4". Will pushing it in, pull the slide back about 1/2" and then the back of the slide will lift off from the receiver.
3ald3eaver 3 years ago
Use a tool to push the catch in the back (around the firing pin) ALL THE WAY IN. At the same time, pull the slide back about 1/2" and lift the back of the slide up. CAUTION: There are lots of little parts on springs that will fly out. Best to do this over a large cookie sheet to catch all the parts. It takes lots of dexterity to put them all back and get the slide and catch back without the parts flying out.
3ald3eaver 3 years ago
bitch ass faggie boy lol i got you jp
buzz8324 3 years ago
we got it unjammed but i still wanna know how to take it down so i can clean it. Thanks !
jkrzy15 3 years ago