listen.., it looks like it work so don't worry about know it idiots. Plus it makes sense as you put. Less heat and more power..., keep up the good work. I'm changing my Bedini to your setup...thxs.
Hi, thanks for the info, but im still stuck, wondering whats going on in the quantum world. I spin the rotor and two magnets always stop off center of the core. If I put the rotor closer to the core then one magnet stops directly over the core. But the dam thing just wont keep spinning. any pointers?
The negative on the primary battery go’s to the inner 20 gauge wire on the coil which also go’s to the emitter on the transistor and the inner 24 gauge wire from the coil go’s to the collator on the transistor then the neon bulb is connected to the emitter and collator is there any problems you see in this hookup? I noticed when I put a drill bit in the coil it shoots it out and my core is made of drill bits. what on earth is going on
The potentiometer is connected to a 24 gauge outside coil wire. My 1N4007 diode is connected to the positive on the secondary battery. Then the outside 20 gauge wire runs to negative on the secondary battery and on the positive on the primary battery.
Nice video! Hi I have been trying to get the bedini motor to work, but the wheel just comes to a stop. My setup is 1N4001 diode is connected on the emitter to the base on the transistor. Then the base is connected to a 470 resister. Then resister is connected to the potentiometer.
Tesla believed The law of conservation of energy for no other reason than you can not prove a Negative.
Indeed The law of conservation of energy has only been proven in that it has never bean disproved in the hundreds of years of testing but not a Fact just a Accepted belief to science, like god is to priests.
Free energy has been here for a while ,But the Oil companies want these technologies unknown to the masses,Get a motor that works with the power of magnets only at LT-MAGNET-MOTORdotCOM ,Let the revolution begin!
you could build this circut for free. tip3055 samples from vishay resistors and diodes also from vishay and neon bulb from a diposabale camara and pots from old psu's
OK the first time I did this I got it to work. What I did was follow these instructions then I wire it up like introvertibrate.Then I burned it out and noticed that every time I follow these instructions It does not work. I am trying to get the process down so I can make a Hi def Instructional video. Also watch for misinformation, the government is out there tryin to taint the waterhole. Go check out my youtube for bedini announcment.
Hi, my name es Ricardo and I follow your instructions, but somewhere I lost and fail, Now I want you help me please to find my mistake I have same photos and video of my proyect.
This comment has received too many negative votesshow
People give Bedini way too much credit. He didn't invent a pulse motor or back emf charging, he just put the two together. He clearly does not understand some pretty basic things about how it works and uses BS terms like "radiant energy".
Tesla created that term for energy from the Sun. Leave Tesla out of your scams Bedini and your small following of idiots. It is not >100% as Bedini claimed and he could not make a window motor self run on a cap. That (mike motor) is a fake too.
I am glad you wrote me. I am not going to dispute the OU claim. I have told people the OU is an oxymoron. I do have a question; I have a fry's here is vegas, so If i get the t03 socket and put 2 nte327 on it in parallel, this will increase power? All I am doing now is wanting to increase power to run an alternator on the other end. I am tired of losing heat from the relay and reed switch and want a circuit to do the work. I also found a way to feed the emf back into coil to use less power.
Yes or you could even just parallel a bunch of what you are using tip3055 or 2n3055 will work fine. Takes 5 minutes to try it yourself, you will see. Bedini uses 3 or what ever he uses on his ten coil. It's all good.
I will take a photo or two of what this thing should look like in a few weeks, busy with something right now.
I can make that run on nothing but a tiny relay or even just a big a zener diode but it won't charge a battery as expected.
Planning to write something up in the near future that will explain how a whole bunch of OU devices worked and will upload it somewhere. PM and remind me of who you are and I will give you a link when I get around to it.
@IdiotSlapper Tesla created that term for energy from engine of creation. His own words. And he used the term to cover all his free energy work. If he meant Solar he would of said Solar.
@IdiotSlapper John Bedini is a GOD. He is a great man who showed the world how to do free energy, and THOUSANDS of people have done it, including me. YOU are an idiot moron TROLL who has NOTHING to give, except bullshit. YOU are too STUPID to be able to make even a small ou machine, so go fuck yourself you little troll.
Use a breadboard, again the soldering components to each other is more of the moron Bedini groups magical thinking BS. Pound for pound they are some of the dumbest people out there.
You will wish you did when you disconnect charge battery while running and have to replace the transistor. You can buy a t03 socket and not solder at all. Parallel two 2n3055 or NTE327 whatever to increase power.
I believe two separate efficient units working together can create more electricity out than in just by using the power already present in magnets. Magnets are the fuel, not some special magical energy.
Magnets are not fuel and you can not get more out than in here at least. It is what is and conventional OU.
If you want less current draw and not charge a battery but better motor, slight change to trigger side will fix that.
If yo want to cancel back emf of motor for OU, you can do that with a magnet plate sending pulses through the shaft but not going into that here. Nothing magical about a pulse motor, magnets, back popping a battery, etc.
You do need to wind the coil bifiler and it is not "radiant energy".
These people are morons. But is you want to play with one of the first motors ever invented have fun. It will charge a battery slowly and fix a sulfur problem. BUT not OU and all the magical thinking these morons preach.
for the 1n4007, just buy the silicon diode assortment at radio shack. A few of each for much less. Lose the 100 ohm resistor and that 120 volt neon will not save your transistor.
never mind the last question I got it working. Thank you for your video I don't have a video camera . I have a camera for the pc do you know if I can make a youtuve video with it? your videos and help are very good don't put attention to negative comments.
I am glad you got it working. You must make very small adjustments to the pot to find the "sweet spot" to achieve the the highest out put with the highest RPM's
Hi your video is very good I would like to ask you about the connection for the coil .I am a bit confused The coil has 2 leads on top and 2 on the bottom one thin one thick wire which one is the power and which is the charge is the pot connected to the thin or to the thick on top Thanks
Thin to the pot, thick is 22awg to the + and emmiter I believe. I have to look at the circuit again.the thin wire triggers the pulse to run the motor.
that happnd to me too. I soldered the 100ohm resistor from the back end of the pot to the base and the light to the front end of the pot to the small coil wire. You have to give it a good spin to get it going also. Check marthal7 and truthbeknown vids
which way did you wind the coil [cw or ccw] and which way is the current flowing through the coil prom the primary batt[cw or ccw] as I havent seen anything about that mentioned anywhere
frustrated ranter it does matter in terms of stator performance (slightly) the damn thing will get current induced into it either way one is just a little more optimal than the other I think its "lenz law"?
That wasn't the question I asked and it was kinda dumb of me since I know about mag field induced through coils. Really the reason I asked is because I was not sure If there was something else going on in the coil
Thanks Todd ! Im looking foward to see the wrap job of the coil. Im cutting my end caps getting the bolt, wire, and tape. Getting prepared to learn the wrap techneque of the coil! Thanks Again !-Bob W.-
Ok... I took a 3/8 bolt and made end caps from lexan. I took a large hole saw and just made exact ends from the lexan. I wrapped one layer of electrical tape 2 1/4 in along the bolt. I took 2 strands of 22awg mag wire and wrapped it 400 times. I hope this helps. My next vid I made a new coil so I will show how I wrapped that. Best of luck!!
Ah this is the video I have been looking for :) I am on the verge of building my own bedini mortor. I'm still learning about electronics, but I can't wait to see if this thing really does what they say it does for myself. Thanks.
I'm new to game so I asking. Do you have to power it up with a first to charge the second or viseversa? Or your setup just works better ?...thxs
Mrinfoone 2 months ago
listen.., it looks like it work so don't worry about know it idiots. Plus it makes sense as you put. Less heat and more power..., keep up the good work. I'm changing my Bedini to your setup...thxs.
Mrinfoone 4 months ago
When we are looking to build multiple coils for larger battery bank charging.. would a different setup be needed?
RealDIYEnergy 7 months ago
Hi, thanks for the info, but im still stuck, wondering whats going on in the quantum world. I spin the rotor and two magnets always stop off center of the core. If I put the rotor closer to the core then one magnet stops directly over the core. But the dam thing just wont keep spinning. any pointers?
333kgb 9 months ago
The negative on the primary battery go’s to the inner 20 gauge wire on the coil which also go’s to the emitter on the transistor and the inner 24 gauge wire from the coil go’s to the collator on the transistor then the neon bulb is connected to the emitter and collator is there any problems you see in this hookup? I noticed when I put a drill bit in the coil it shoots it out and my core is made of drill bits. what on earth is going on
333kgb 10 months ago
The potentiometer is connected to a 24 gauge outside coil wire. My 1N4007 diode is connected to the positive on the secondary battery. Then the outside 20 gauge wire runs to negative on the secondary battery and on the positive on the primary battery.
333kgb 10 months ago
Nice video! Hi I have been trying to get the bedini motor to work, but the wheel just comes to a stop. My setup is 1N4001 diode is connected on the emitter to the base on the transistor. Then the base is connected to a 470 resister. Then resister is connected to the potentiometer.
333kgb 10 months ago
this Bedini circuit is just a copy of a Joule Thief circuit maybe we should just call it a Bidini Thief. :-o
one2manyification 10 months ago
Thanks for the great video...finally a clear explanation together with a clear vid...great stuff
Mytubepalma101 10 months ago
Tesla believed The law of conservation of energy for no other reason than you can not prove a Negative.
Indeed The law of conservation of energy has only been proven in that it has never bean disproved in the hundreds of years of testing but not a Fact just a Accepted belief to science, like god is to priests.
dragondeathlord 1 year ago
@dragondeathlord
Sorry mistyped meant to type Tesla did not Believe In the law of conservation.
And till a hundred years ago it was Accepted belief that Heavier than air Machine could not fly.
It might seem silly to try to disprove The law of conservation of energy. But it is sillier that science stopped trying.
dragondeathlord 1 year ago
Gotta ask, should i sink the trans?
Kasatome 1 year ago
This has been flagged as spam show
Free energy has been here for a while ,But the Oil companies want these technologies unknown to the masses,Get a motor that works with the power of magnets only at LT-MAGNET-MOTORdotCOM ,Let the revolution begin!
despinapjr 1 year ago
This has been flagged as spam show
Free Energy is real and its here! The Oil companies are doing everything in their power to stop these
information. If you want a Free energy machine do a search in youtube for the LT MAGNET MOTOR , Join the
revolution!
buchananfibbing 1 year ago
Amazing!! Well done! That's what I call instructions.
Thank you very much.
W A
wwaltersouza 1 year ago
VERY USEFUL ... THANX!
sneekyfeet1 2 years ago
you could build this circut for free. tip3055 samples from vishay resistors and diodes also from vishay and neon bulb from a diposabale camara and pots from old psu's
coilsinamotor 2 years ago
how much did it all cost?
kennysc12 2 years ago
prlly about $35
salzahrah 2 years ago
OK the first time I did this I got it to work. What I did was follow these instructions then I wire it up like introvertibrate.Then I burned it out and noticed that every time I follow these instructions It does not work. I am trying to get the process down so I can make a Hi def Instructional video. Also watch for misinformation, the government is out there tryin to taint the waterhole. Go check out my youtube for bedini announcment.
fcptv 3 years ago
Hi, my name es Ricardo and I follow your instructions, but somewhere I lost and fail, Now I want you help me please to find my mistake I have same photos and video of my proyect.
Tanks you so mach
loaajah 3 years ago
I don't know if anyone else noticed but you have a problem when your explaining how to connect the trigger wires from the coil.
CyrussTheVirus 3 years ago
It's called perf board
pleasecho2 3 years ago
This comment has received too many negative votes show
You are talking to yourself , idiot slapper.
SpikedChrist82 3 years ago
This comment has received too many negative votes show
People give Bedini way too much credit. He didn't invent a pulse motor or back emf charging, he just put the two together. He clearly does not understand some pretty basic things about how it works and uses BS terms like "radiant energy".
Tesla created that term for energy from the Sun. Leave Tesla out of your scams Bedini and your small following of idiots. It is not >100% as Bedini claimed and he could not make a window motor self run on a cap. That (mike motor) is a fake too.
IdiotSlapper 4 years ago
I am glad you wrote me. I am not going to dispute the OU claim. I have told people the OU is an oxymoron. I do have a question; I have a fry's here is vegas, so If i get the t03 socket and put 2 nte327 on it in parallel, this will increase power? All I am doing now is wanting to increase power to run an alternator on the other end. I am tired of losing heat from the relay and reed switch and want a circuit to do the work. I also found a way to feed the emf back into coil to use less power.
ktservicescorp 4 years ago
Yes or you could even just parallel a bunch of what you are using tip3055 or 2n3055 will work fine. Takes 5 minutes to try it yourself, you will see. Bedini uses 3 or what ever he uses on his ten coil. It's all good.
IdiotSlapper 4 years ago
I will take a photo or two of what this thing should look like in a few weeks, busy with something right now.
I can make that run on nothing but a tiny relay or even just a big a zener diode but it won't charge a battery as expected.
Planning to write something up in the near future that will explain how a whole bunch of OU devices worked and will upload it somewhere. PM and remind me of who you are and I will give you a link when I get around to it.
IdiotSlapper 4 years ago
@IdiotSlapper Tesla created that term for energy from engine of creation. His own words. And he used the term to cover all his free energy work. If he meant Solar he would of said Solar.
dragondeathlord 1 year ago
@IdiotSlapper John Bedini is a GOD. He is a great man who showed the world how to do free energy, and THOUSANDS of people have done it, including me. YOU are an idiot moron TROLL who has NOTHING to give, except bullshit. YOU are too STUPID to be able to make even a small ou machine, so go fuck yourself you little troll.
MrFuntucky 1 year ago
Use a breadboard, again the soldering components to each other is more of the moron Bedini groups magical thinking BS. Pound for pound they are some of the dumbest people out there.
You will wish you did when you disconnect charge battery while running and have to replace the transistor. You can buy a t03 socket and not solder at all. Parallel two 2n3055 or NTE327 whatever to increase power.
IdiotSlapper 4 years ago
I believe two separate efficient units working together can create more electricity out than in just by using the power already present in magnets. Magnets are the fuel, not some special magical energy.
ktservicescorp 4 years ago
Magnets are not fuel and you can not get more out than in here at least. It is what is and conventional OU.
If you want less current draw and not charge a battery but better motor, slight change to trigger side will fix that.
If yo want to cancel back emf of motor for OU, you can do that with a magnet plate sending pulses through the shaft but not going into that here. Nothing magical about a pulse motor, magnets, back popping a battery, etc.
IdiotSlapper 4 years ago
TIP3055 is wrong. 2n3055 or even better NTE327 from Fry or Norvac in Beaverton.
IdiotSlapper 4 years ago
You do need to wind the coil bifiler and it is not "radiant energy".
These people are morons. But is you want to play with one of the first motors ever invented have fun. It will charge a battery slowly and fix a sulfur problem. BUT not OU and all the magical thinking these morons preach.
for the 1n4007, just buy the silicon diode assortment at radio shack. A few of each for much less. Lose the 100 ohm resistor and that 120 volt neon will not save your transistor.
IdiotSlapper 4 years ago
I meant to say "you do NOT need to wind bifiler"
There is ZERO difference. Test it out for yourself.
Wind trigger coil first. and a bit shorter and smaller 20% than the primary windings on top.
IdiotSlapper 4 years ago
Bedini is not OU as claimed and the yahoo group is run by morons.
IdiotSlapper 4 years ago
Wrong transistor. You want the one in the T03 package (metal can)
IdiotSlapper 4 years ago
can you email me the site for the diagram please
pipeorganphil 4 years ago
I am using reed switches and they keep frying... How can I stop that from happening?
leewayx9 4 years ago
Stop using them.
IdiotSlapper 4 years ago
never mind the last question I got it working. Thank you for your video I don't have a video camera . I have a camera for the pc do you know if I can make a youtuve video with it? your videos and help are very good don't put attention to negative comments.
1miltond 4 years ago
I am glad you got it working. You must make very small adjustments to the pot to find the "sweet spot" to achieve the the highest out put with the highest RPM's
ktservicescorp 4 years ago
can you email me the site for the diagram please
Pwordchernoir 4 years ago
Hi your video is very good I would like to ask you about the connection for the coil .I am a bit confused The coil has 2 leads on top and 2 on the bottom one thin one thick wire which one is the power and which is the charge is the pot connected to the thin or to the thick on top Thanks
1miltond 4 years ago
Thin to the pot, thick is 22awg to the + and emmiter I believe. I have to look at the circuit again.the thin wire triggers the pulse to run the motor.
ktservicescorp 4 years ago
i have watched youre vid many times you have mentioned the bottom charging wire twice,
you have it ging to places could you clarify that bit
acemax96 4 years ago
thanks for the reply, keep up the good work
acemax96 4 years ago
when connecting up to the pot the instructions ae different from inverts set up
all i get from mine is the neon making a noise
acemax96 4 years ago
that happnd to me too. I soldered the 100ohm resistor from the back end of the pot to the base and the light to the front end of the pot to the small coil wire. You have to give it a good spin to get it going also. Check marthal7 and truthbeknown vids
T
ktservicescorp 4 years ago
FrustratedRanter has a good question there...
Anyone have a good answer or is there no answer because it doesn't matter which way it's wound, cw or ccw?
Ty 4 a good vid here and grats on your 'I did it!!!' device. :)
RockManAU 4 years ago
Depends on if you are right handed or left handed. lol
ktservicescorp 4 years ago
which way did you wind the coil [cw or ccw] and which way is the current flowing through the coil prom the primary batt[cw or ccw] as I havent seen anything about that mentioned anywhere
FrustratedRanter 4 years ago
frustrated ranter it does matter in terms of stator performance (slightly) the damn thing will get current induced into it either way one is just a little more optimal than the other I think its "lenz law"?
meier25 4 years ago
That wasn't the question I asked and it was kinda dumb of me since I know about mag field induced through coils. Really the reason I asked is because I was not sure If there was something else going on in the coil
FrustratedRanter 4 years ago
Great work! I have done the 3055 on my videos if you are interested at looking at them.
Note on your neon, I think there is resistor in the housing that makes it so dim.
marthale7 4 years ago
Thanks Todd ! Im looking foward to see the wrap job of the coil. Im cutting my end caps getting the bolt, wire, and tape. Getting prepared to learn the wrap techneque of the coil! Thanks Again !-Bob W.-
uncleshorty 4 years ago
Excellent can you show making a coil then I might get it to work! Thank You Much!
uncleshorty 4 years ago
Ok... I took a 3/8 bolt and made end caps from lexan. I took a large hole saw and just made exact ends from the lexan. I wrapped one layer of electrical tape 2 1/4 in along the bolt. I took 2 strands of 22awg mag wire and wrapped it 400 times. I hope this helps. My next vid I made a new coil so I will show how I wrapped that. Best of luck!!
-Todd-
ktservicescorp 4 years ago
Ah this is the video I have been looking for :) I am on the verge of building my own bedini mortor. I'm still learning about electronics, but I can't wait to see if this thing really does what they say it does for myself. Thanks.
W1930U7 4 years ago