if your xbox overheats and you've had it for a while, make sure the console isn't sucking hot air from a near by heating source. Also make sure that the "brick" or power source has room to breath. If that doesnt work open up your xbox (youtube instructions) remove all the dust and your good!
Thanks for this vid. It was the very first one I ever seen for this mod and it has made my xbox run a hell of a lot cooler but I don't care about the noise. Can't here it with turtle beaches on. And with the help of this mod my friends have actually gave me a few bucks to do these for them haha!
DON"T CUT YOUR WIRES CLOSE TO THE PLUG! If you cut them close to the plug, and then decide that the mod is way too loud, it will be very difficult to undo. Cut the fan wires it the middle as well.
I had done this like a year ago. I got my 360 in 2007 and this tut works great. My Xbox has never gotten the rrod either. Not even once. Due to the fact that I followed this tut. Sure it's louder but at least it keeps my Xbox from getting the rrod. Had an Xbox before this one that had no fan mod and it croaked in 2 years
@StupidSpawn I clean it at least 2 times a year, im not a smoker, and my xbox is on its side, on the table for better ventilation. And this fan mod should help alot! ;)
Badass. GPU heat sink isn't very hot and the CPU heatsink is indeed almost cold; but there's one heatsink in front of the CPU heatsink that still gets very hot (though, nominally, not as hot as before). Still, helps a lot.
@ImmortalUniverse if u used the x-clamp fix thats just temporary. a perma fix/or a fix that will last you much longer than a x-clamp fix is a Reball/Reflow. Depends wich one you need.
@IProKaZ You dont Reflow the Solder. -.- you reflow the GPU, ramchips whatever. but eventually you will have to do a reball aswell if you are on it for to long xP
hey guys i have a problem and i think its with the mother board, when i turn on my 360 the fans just get faster and faster then i get 2 rings, not sure what to do can someone give me some closure?
Just so you all know, this steals power from your dvd drive, there is a reason your dvd drive needs/gets the amount of power it does, if you need to have a 12v fan just bridge the two points next to the plug in, it is much safer/faster than this method.
@ShotsDesignsHD I am glad that someone else realized this. For those who are reading this tutorial, you might want to consider POT tweaking your Disk Drive after doing this. POT tweaking is very useful for those who receive the "DVD Error" upon achieving this mod. However, also keep in mind that you are also slowly degrading the power of the laser when you Pot tweak.
@ICRMX Yes you can wire is wire just make sure its rated for 12 volts....i have never seen wire that isnt rated for it so just go ahead with any wire.
my fan dosnt even want to turn at all when the xbox i s on. the black wire was worn so i soldered solder wire to the black wire. would it still work? btw the red and black wire fan dosnt want to work... please help
Or... You can connect a molex connecter under the power connecter, run a 12v fan. and keep your original fan. and its safer! 3 fans(15v) > 2 fan (12v)
I did this mod, then I plugged everything back in, and instead of getting the 2 red rings.. i got the 3 ring! WHAT WENT WRONG! HOW DO I FIX THIS? PLEASE HELP!
iv'e had this mod for over 5months now it still works great no over heating whats so ever itouch the back of my xbox after an 1hour of gameplay and it still rus cold totally recommended thanks man :)
Just did this mod. did make the fan faster (noticably louder, but thats ok, i like the sound of fans lol, May put a switch in who knows) Will write back in a few days for update
if you have a computer fan get the red and black wire make sure they dont touch go to radio shack buy a usb cable and cut the end attach the red wire to fan red do the same with black and hook usb cable to use slot on computer or xbox and there you go for more advice go on you tube and type in how to make a usb fan mod
Sorry, im kinda a retard but uh, What do you hook it up with to make it run...cuz i have a small computer fan...but i have no clue on how to make it run. Sorry noob question. But thx if someone can answer it =D
Well i decided minus all the negative remarks on this mod to try it out myself. The result is very nice....runs a lot cooler and don't see any signs of the system working much harder. I would recommend this mod if you are having problems with your box.
so i did this mod but i still have the three red lights and i tried resetting it twice n im still getting it my fans are on and loud but i have no idea
what i did was on the side where the hard drive isnt on i put the fans there from an older RROD xbox, so they suck in air and move air out creating a steady flow of cool air over the GPU.never had to buy a new xbox again hope this helped you guys!!!!!
easiest thing to do is buy the inter-cooler, take out the stock fan and let the intercooler itselfcool the system, did it to mine and it works great plus its not that much louder, to do this you must take out the entire stock fan or it sucks
I started using a lighter instead of wire strippers in class (electronics class) and my professor first panicked and then looked at me like I was crazy.
This is what Microsoft should of did from the get go, I did this my self and my XBOX 360 works flawlessly, it no longer freezes or get hot . Its literally cool to the touch now, it may be a little loud but when you think about all the work the XBOX 360 has to do the fans almost have to run at 12volts to stay on top of the heat issue. I believe this mod would add years to your XBOX 360. Its something Microsoft should of done.
It's also a good idea to pop the fan rotors out and add a drop of turbine oil to the bearings, especially on the GPU side. Every one I've seen is bone dry on that side. Talismoon fans are no better, they just light up. Whoop dee fuckin' doo. =P
@camarolover1982 no just replace your fan and do this mod and you will be fine. if your fans not working at all that mean your fan have broken do to wear and tear or just faulty fans from the get go.....
@ak47killer200 well. this doesnt apply to me anymore lol. i did the mod and it worked but then the xbox then just wasnt repairable anymore. so i just went and bought i new one. thanks tho
Or just grab some fucking Talismoon whisper cool Fans, also avoid the New 360 microsoft fixed nothing, and with it's vent's it's pretty damn hard to work on for one not experienced with computers.....seriously, what were they Thinking!? LOL
@Sagerstuts Are you retarded? In combination these fans pull a MAX of .8 amp. Your CD rom pulls a max of 1.4 amps. thats 2.2 amps on the 12v rail. WHICH THERE IS ONLY ONE THING ON.
gawd dude.. your a hack.. what a hack job.. 2 issues here, your using the dvd 12 v source, bad juju, the dvd 12 v source is only rated at .3 amps. your pulling way too much amps for that thing now.. you should ALWAYS solder your connections.. and the way your splitting your dvd 12v line, is a hack.. there's much better ways of doing this. your using a lighter to strip the shielding. doing this weakens the wire and changing the resonance of the line. all bad juju.. it may work for awhile.
@danratsnapnames long enough to make it past your warranty work i'll bet.. maybe last a year or less.. dude.. if you want to see how it should be done, feel free to ask for help.. i'm willing to show you the right way to do this.
n e ways i just did this fan mod to keep it cooler... its real loud but blows alot more air. and am worried if the fans are going to break?? will they?
@Omari1125 leeching power off of your dvd drive however causes power fluctuations which can lead to a fried pcb, a broken dvd drive or a wasted power brick.
I shall use this mod and i will win...retaliation microsoft...RETALIATIOOOOOOOOOOOOOOOOOOOOOOOOONNNNNNN!!!HAAAHAHAHAHAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA!!!
@408427 Wait what?R u serious?Friggin microsoft.They just dont like how they didnt get the credit for fixing the RROD themselves so they make other people pay for taking away the spotlight.Friggin corporate scumbags... >:(
So if you do exactly as the tutorial shows it will work!
problem i encountered>>> When i turned on my xbox I'd get the 3 RROD so what you have to do to solve his problem is to turn around your dvd drive cable(black one) and try to turn on XBOX again! it will work like a charm!
Sprint guys just did it and had one problem but it's solved! If you your DVD drive power cable backwards your fans won't spin and you'll get the 3 RROD. So all you have to do is turn around the DVD drive cable ( black one) and it should work fine!
I have a weird problem. I managed to overload the source output for the fan, so I blew up the transistor. I can't use that power source. My fan is a talismoon whisper legacy which now runs at full speed with the DVD Drive as a power source. When I have this set up, my xbox 360 won't boot up if I'm using a hard drive. Can I fix this without soldering?
who ever came up with this idea is F****N smart. most simplest and safest way to run the fans at 12 volts. beats all other tutorials that ive seen. smart thinking bro...
It's not a rrod fix it just prevents it. The stock fans are 12v fans but they are running on 5v by doing this they run at their full potential thus keeping the xbox cooler stopping it from over heating and damaging the joints between the cpu and the motherboard and the gpu and the motherboard, meaning no Rrod. If your wanting to repair your rrod 360 its really not hard. I bought an xclamp fix kit from ebay and followed one of the many tutorials online then reflowed the main chips with a heat gu
Thanks man my xbox was being weird the audio wasnt working and my fans stopped working so i took off the heat sinks and cleaned the cpu and gpu that fixed the fan problem but not the sound so i decided to give this a a try and now i got my sound back so i guess the cpu and gpu were getting to hot and this mod keeps the heat sinks cool you saved me from buying a new xbox thanks :)
do not do this it will only give your xbox rrod with 1 ring on the forth led
bigdaddy16324 1 hour ago
I can tell by the de-child proofed lighter that your definitely a stoner. Props man
korydak1lla 1 month ago 4
@korydak1lla And then we CHEECH'D!
sh3lbot 4 days ago in playlist Favorite videos
if your xbox overheats and you've had it for a while, make sure the console isn't sucking hot air from a near by heating source. Also make sure that the "brick" or power source has room to breath. If that doesnt work open up your xbox (youtube instructions) remove all the dust and your good!
MayaElite57 1 month ago
@MayaElite57 HOW TO FIX YOUR OVERHEATING XBOX
MayaElite57 1 month ago
Thanks for this vid. It was the very first one I ever seen for this mod and it has made my xbox run a hell of a lot cooler but I don't care about the noise. Can't here it with turtle beaches on. And with the help of this mod my friends have actually gave me a few bucks to do these for them haha!
THEONL1NEH3R0 1 month ago
DON"T CUT YOUR WIRES CLOSE TO THE PLUG! If you cut them close to the plug, and then decide that the mod is way too loud, it will be very difficult to undo. Cut the fan wires it the middle as well.
jeffreykral 2 months ago
you should solder your wires...
nata911 2 months ago
do not do this, it will give you xbox rrod. i did it and now i have to get a new fan and new dvd drive cable
AcEPFL 2 months ago
Any household wires i can use for this? Idk wat to use and i have a ton of wire in my basement all different kinds plz answer
FMLxHD 3 months ago
@FMLxHD Any wire that fits will do. I used wires from old PC fans but you can use anything like speaker wire, as long as its insulated.
tipoomaster 2 months ago
Yea Shrink tubing makes everything nice and neat looking.
gjones172 3 months ago
Nice technique never seen lighter style
r0mulyni2 3 months ago
Are you trying to make an xbox explode?
xyz41100 3 months ago
You can also connect the positive to a 12v transistor under the front side of the from dvd drive and ground on the frame of the Xbox
mrmrmrpatron 3 months ago
your soldering skills are fab!...oh, wait :I(
dgordon86 4 months ago
I had done this like a year ago. I got my 360 in 2007 and this tut works great. My Xbox has never gotten the rrod either. Not even once. Due to the fact that I followed this tut. Sure it's louder but at least it keeps my Xbox from getting the rrod. Had an Xbox before this one that had no fan mod and it croaked in 2 years
CodyOsieczonek 4 months ago
@CodyOsieczonek its so loud but worth not dealing with fuckheads at ms and paying for repairs
SmashOut200HD 4 months ago
@SmashOut200HD instal games to your hardrive
i think it makes the 360 sound less
iHateThisShirt 3 months ago
@iHateThisShirt thats the DVD not spinning up
SmashOut200HD 3 months ago
you make this look so easy, but i know when i try this, it is going to take me hours.. lol
JenkoFX 4 months ago
You cut like a boss.
Jibbletoad 4 months ago
thanks pal worked great
GhostY2Pac 4 months ago
i have better solution, get the arcade version!!!!
creap32 5 months ago
@creap32 I have the arcade version. It still got red rings etc etc no difference. its just that xbox are poorly made consoles.
XTGEcolditz 4 months ago
@XTGEcolditz It could be that your a smoker, keep your xbox 360 on a carpet, or dont clean it at all!
StupidSpawn 4 months ago
@StupidSpawn I clean it at least 2 times a year, im not a smoker, and my xbox is on its side, on the table for better ventilation. And this fan mod should help alot! ;)
XTGEcolditz 4 months ago
@StupidSpawn Honestly man if you want a good fan thats quiet and its a 12volt van WITH lights then pm me for the link.
StupidSpawn 4 months ago
Badass. GPU heat sink isn't very hot and the CPU heatsink is indeed almost cold; but there's one heatsink in front of the CPU heatsink that still gets very hot (though, nominally, not as hot as before). Still, helps a lot.
Before, I had to do the towel method twice a day.
L30n974 5 months ago
you can also find a xbox 360 KEY on EBAY , so you dont damage the xbox360 when you open it .
very handy for a few bucks.
i got it with my RROD fix kit .
i bought my xbox 360 of ebay and fixed it myself:)
ImmortalUniverse 5 months ago
@ImmortalUniverse if u used the x-clamp fix thats just temporary. a perma fix/or a fix that will last you much longer than a x-clamp fix is a Reball/Reflow. Depends wich one you need.
IProKaZ 5 months ago
@IProKaZ i did relow the solder.
and it is permanent.
because i fixed the high temps .
the solder stays cool.
so it doesnt break again.
ive got temp sensors inside.
ImmortalUniverse 5 months ago
@IProKaZ You dont Reflow the Solder. -.- you reflow the GPU, ramchips whatever. but eventually you will have to do a reball aswell if you are on it for to long xP
IProKaZ 5 months ago
XCM core fans 20 bucks .
bigger GPU heatsink 15 bucks
on ebay
best ever for overheat fix .
my temps are 50 c for the cpu after hours on max. 55 c for the GPU after hours on max
but they are running on 5 volts .
i can even go higher in fan speed.
but its not needed, the new case i bought also has better ventilation on top.
also a XCM case/
ImmortalUniverse 5 months ago
hey guys i have a problem and i think its with the mother board, when i turn on my 360 the fans just get faster and faster then i get 2 rings, not sure what to do can someone give me some closure?
deathspainkiller 5 months ago
@deathspainkiller
thats how overheating starts .
the fan at the rear can stay on a 5 v source .
but you need to buy on ebay a bigger heatsink for the GPU under de DVD player ,for best results .
and buy the "Twin core fans" from XCM.
also on ebay.
then the temps will be much lower and the noise wil be much less.
if you dont have the fans and heatsink yet, you can leave the top of the xbox off and just use the bottom plate for a while.
this way the heat can escape at the top.
ImmortalUniverse 5 months ago
@deathspainkiller
give the fan at the rear a good cleanup and the wings on the fan.
and try to clean the dust from the inside of the xbox.
the power block also must have air to breath.
you dont have to mod the fan at the rear .
its normal it runs faster , because its speed controlled.
the speed control of the bios is terrible.:)
but thats no big deal , when you got a new HEATsink for the GPU and 2 twin core fans of XCM.
the fans b.t.w. are plug and play , no solder.
check ebay.
ImmortalUniverse 5 months ago
I did all you said but I think I cut the brown cord to short and now it doesn't reach the plug what do I do ???
Tjphx623 5 months ago
@Tjphx623 Cut a bit off the bit you cut off, and then heat the ends up and stick the metal bits of the wire together
coolcar100 5 months ago
Fan works, but the disk tray doesn't open
MultiRandomness99 5 months ago
@MultiRandomness99 u messed up somthing or did the wronge wire on the dvd power cable
Aimanrulez 3 months ago
get a life
MrWeeman8888 6 months ago
hey thanks buddy my fan is running full speed now. will this ruin anything on it or will I get banned?
weswes1995 6 months ago
Just so you all know, this steals power from your dvd drive, there is a reason your dvd drive needs/gets the amount of power it does, if you need to have a 12v fan just bridge the two points next to the plug in, it is much safer/faster than this method.
ShotsDesignsHD 6 months ago
@ShotsDesignsHD I am glad that someone else realized this. For those who are reading this tutorial, you might want to consider POT tweaking your Disk Drive after doing this. POT tweaking is very useful for those who receive the "DVD Error" upon achieving this mod. However, also keep in mind that you are also slowly degrading the power of the laser when you Pot tweak.
TheAloha1991 6 months ago
can i fix my xbox if i have red rings now?
kev600K 7 months ago
YOUR FUCKING TUTORIAL RRODd MY FUCKING XBOX!!
Bluishist 7 months ago
@Bluishist im pretty sure its your fault for being inept
TheMydroid 7 months ago
@Bluishist ur most likely 2 years old and used potato sticks as ur wire
kcon321 6 months ago
@kcon321 Potato sticks, very creative faggot.
Bluishist 4 months ago
hey man great vid. so my question is can i use any type of wire? (the one from 0:57 ?) please some1 helpp!
ICRMX 8 months ago
@ICRMX Yes you can wire is wire just make sure its rated for 12 volts....i have never seen wire that isnt rated for it so just go ahead with any wire.
llamma1010 7 months ago
my fan dosnt even want to turn at all when the xbox i s on. the black wire was worn so i soldered solder wire to the black wire. would it still work? btw the red and black wire fan dosnt want to work... please help
mastacor 8 months ago
Or... You can connect a molex connecter under the power connecter, run a 12v fan. and keep your original fan. and its safer! 3 fans(15v) > 2 fan (12v)
dartz315 8 months ago
Ok speaker wire goes to red and brown wire pluse dvd drive
jgraham35 8 months ago
I did this mod, then I plugged everything back in, and instead of getting the 2 red rings.. i got the 3 ring! WHAT WENT WRONG! HOW DO I FIX THIS? PLEASE HELP!
goofywhiz 8 months ago
@goofywhiz plug the av cable lol
AnonymousTutorialz 8 months ago
@AnonymousTutorialz kk its fixed.. thanks anyways.
goofywhiz 8 months ago
100th like!!
goofywhiz 8 months ago
iv'e had this mod for over 5months now it still works great no over heating whats so ever itouch the back of my xbox after an 1hour of gameplay and it still rus cold totally recommended thanks man :)
AnonymousTutorialz 8 months ago
@AnonymousTutorialz hey wat type of wire (the one from 0:57) did u use to do this mod? i need help on doing this. can i use any type of wire?.
ICRMX 8 months ago
If I do this mod, can I still attach LED's to my xbox? Don't they use the same power source?
goofywhiz 8 months ago
erm... my cd tray wont open now... the fan turns on though...
Bweihsification 8 months ago
Just did this mod. did make the fan faster (noticably louder, but thats ok, i like the sound of fans lol, May put a switch in who knows) Will write back in a few days for update
HprSaint 9 months ago
@HprSaint hey wat type of wire (the one from 0:57) did u use to do this mod? i need help on doing this. can i use any type of wire?.
ICRMX 8 months ago
thanks ass hole now i have a broken jtag . it dosnt work for all drives
HulkGetsWasted 9 months ago
Ur retarded it will give less power to the dvd drive so your xbox will still overheat just cut the plug off a 12 ac/dc adapter it works better.
adamroxdahouse 9 months ago 2
@adamroxdahouse aye someone smart i did that. and was about to post same comment as you.
hotpies4567 9 months ago
@adamroxdahouse or dont cut any wires at all and lleave it be.
best thing is to get a bigger heatsink for the GPU , there are many different imitation.
some are really good.
check ebay for the biggest heatsink.
and check for a few core fans of XCM.
also check the XCM website for more cool stuff.
like cases .
my case is the chameleon case with x logo on top.
it also has better ventilation then the original case had.,
ImmortalUniverse 5 months ago
my fan is not working at all...will this fix it?
prettythug62494 9 months ago
SO DOES THIS FIX THREE RROD?
spidervenom53 9 months ago
If you run it off of your dvd drive xbox live thinks your playing a burnt game and bans you.
CovenantKilla225 9 months ago
Quik to tha point love it
abjamesbond007 9 months ago
i did this 8 months ago and its still working no overheating thanks
AnonymousTutorialz 9 months ago
what went wrong if i got three red rings? Lol
mrcool714 9 months ago
@hackingjungle Will this get me banned on xbox live?
xspartanX3x 9 months ago
@xspartanX3x No.
cod4madass 9 months ago
OMG.....you cut the wires too close to the pin connector.....your never be able to use that again!
Melting the wires like that gets residue on the wire!
Jesus Christ man.......solder those frekin wires.....please dont do that to your xbox dont leave bare wires like that!
Its an expensive xbox not a crappy $20 dollar boom box you bought at the swapmeet!
radiuslight 9 months ago
@radiuslight It's just a 360..a old one at that.Iwouldn't mod the newer one but the old ones you really need to.
risseer23 9 months ago
if you have a computer fan get the red and black wire make sure they dont touch go to radio shack buy a usb cable and cut the end attach the red wire to fan red do the same with black and hook usb cable to use slot on computer or xbox and there you go for more advice go on you tube and type in how to make a usb fan mod
skilledcrazy8 10 months ago
@skilledcrazy8 Again that will only power that fan at 5 volts because the usb ports are 5 volts
Sagerstuts 10 months ago
Sorry, im kinda a retard but uh, What do you hook it up with to make it run...cuz i have a small computer fan...but i have no clue on how to make it run. Sorry noob question. But thx if someone can answer it =D
DkWowN3rd 10 months ago
So if I wanted to connect this to a pc, do I spot the molecule and join the blue and brown wires
F4H33M97 10 months ago
Well i decided minus all the negative remarks on this mod to try it out myself. The result is very nice....runs a lot cooler and don't see any signs of the system working much harder. I would recommend this mod if you are having problems with your box.
axlerj 10 months ago
its not good to steal power from your dvd drive maybe you can just connect it to a 12v adapter
NINGAhax 10 months ago
@NINGAhax i did it some 2 months ago and no problem
claudeel 10 months ago
This has been flagged as spam show
@claudeel hey wat type of wire (the one from 0:57) did u use to do this mod? i need help on doing this. can i use any type of wire?.
ICRMX 8 months ago
so i did this mod but i still have the three red lights and i tried resetting it twice n im still getting it my fans are on and loud but i have no idea
shanefrancoeur 10 months ago
@shanefrancoeur omfg 3 red lights mean a AV Or HDMI has failed 2 red lights means its over heating!
gunshotbill 10 months ago
Only a fool would want to make their xbox LOUDER.
southport97 10 months ago
@southport97 So,louder xbox... vs posibly,soon to be, dead xbox...id rather take the louder one.
donda2111 10 months ago
what i did was on the side where the hard drive isnt on i put the fans there from an older RROD xbox, so they suck in air and move air out creating a steady flow of cool air over the GPU.never had to buy a new xbox again hope this helped you guys!!!!!
MrMrimtheboss12 11 months ago
easiest thing to do is buy the inter-cooler, take out the stock fan and let the intercooler itselfcool the system, did it to mine and it works great plus its not that much louder, to do this you must take out the entire stock fan or it sucks
dfetzner23 11 months ago
good tut but i think your ment to wire up another fan not the same one coz then its just pluged into the 360 twice
The911SONIC 11 months ago
I started using a lighter instead of wire strippers in class (electronics class) and my professor first panicked and then looked at me like I was crazy.
earlyepitaph 11 months ago
works great , ive been using it for a long time. Good TUT but y use all that stario wire???
mnpilot1212 11 months ago
lol putting out the lighter
zViChrisViz 11 months ago
OMG !!!!!! thanks this works SOOO AWSOME!!!!!
skater4life6721 1 year ago
u are a nob my xbox 360 will not work
TheXratedgames 1 year ago
it's work!!!! thanks
jcaa88 1 year ago
worked thanks :D
machomamajr 1 year ago
doest it matter what of the black wires i cut?
BloodyAzzazzin 1 year ago
@BloodyAzzazzin You need to cut the bottom right cable, when its plugged in look for the bottom right one :-)
CAGGames 11 months ago
@CAGGames thnx:)
BloodyAzzazzin 11 months ago
does it matter wa wire u cut
bluberjunky 1 year ago
with the black wires, is there a certain one your suppose to cut?
TheEazyElmer 1 year ago
soooo much clearer and easier than ANY other fan mod video I have found thanks man
shaydstar 1 year ago
This has been flagged as spam show
@beakerwsw no i am not retarded unlike you dumbass
Sagerstuts 1 year ago
Comment removed
Sagerstuts 1 year ago
This is what Microsoft should of did from the get go, I did this my self and my XBOX 360 works flawlessly, it no longer freezes or get hot . Its literally cool to the touch now, it may be a little loud but when you think about all the work the XBOX 360 has to do the fans almost have to run at 12volts to stay on top of the heat issue. I believe this mod would add years to your XBOX 360. Its something Microsoft should of done.
Omari1125 1 year ago
It's also a good idea to pop the fan rotors out and add a drop of turbine oil to the bearings, especially on the GPU side. Every one I've seen is bone dry on that side. Talismoon fans are no better, they just light up. Whoop dee fuckin' doo. =P
iggy151 1 year ago
Don't rig it into the CD drive. Just solder it to the power jack connections. There is an instructables on this.
iggy151 1 year ago
ok my fans wont work on my xbox now and would this make them work again and better?
camarolover1982 1 year ago
@camarolover1982 no just replace your fan and do this mod and you will be fine. if your fans not working at all that mean your fan have broken do to wear and tear or just faulty fans from the get go.....
ak47killer200 10 months ago
@ak47killer200 well. this doesnt apply to me anymore lol. i did the mod and it worked but then the xbox then just wasnt repairable anymore. so i just went and bought i new one. thanks tho
camarolover1982 10 months ago
Or just grab some fucking Talismoon whisper cool Fans, also avoid the New 360 microsoft fixed nothing, and with it's vent's it's pretty damn hard to work on for one not experienced with computers.....seriously, what were they Thinking!? LOL
kawaiifreak860 1 year ago
you should NEVER do this because your c-d drive will not last very long or work correctly because of lack of power
Sagerstuts 1 year ago
@Sagerstuts Are you retarded? In combination these fans pull a MAX of .8 amp. Your CD rom pulls a max of 1.4 amps. thats 2.2 amps on the 12v rail. WHICH THERE IS ONLY ONE THING ON.
beakerwsw 1 year ago
i did this and it keeps my xbox cool as hell like i could prpbably play it all night but holy crap its loud!!!
MrZquin 1 year ago
@MrZquin same here bro... i got a xbox on Craiglist and i just found out it had this mod.. but i knew it had something csu how loud it is..
dzilla1991 1 year ago
gawd dude.. your a hack.. what a hack job.. 2 issues here, your using the dvd 12 v source, bad juju, the dvd 12 v source is only rated at .3 amps. your pulling way too much amps for that thing now.. you should ALWAYS solder your connections.. and the way your splitting your dvd 12v line, is a hack.. there's much better ways of doing this. your using a lighter to strip the shielding. doing this weakens the wire and changing the resonance of the line. all bad juju.. it may work for awhile.
danratsnapnames 1 year ago
@danratsnapnames long enough to make it past your warranty work i'll bet.. maybe last a year or less.. dude.. if you want to see how it should be done, feel free to ask for help.. i'm willing to show you the right way to do this.
danratsnapnames 1 year ago
@danratsnapnames Hey, you're an asshole. Just felt like saying.
manlavi90 1 year ago
@manlavi90 well, thanks for sharing that prick. lol.
danratsnapnames 1 year ago
@danratsnapnames Haha, nah, I'm just saying. It seems to be working for him.
manlavi90 1 year ago
@manlavi90 yea, but would you want a mechanic using duck tape and bailing wire on your car?! or using scotch tape to fix a rip in your pants!
lol.
danratsnapnames 1 year ago
your a idot that power is from the cd drive making that work harder
kc88kc 1 year ago
n e ways i just did this fan mod to keep it cooler... its real loud but blows alot more air. and am worried if the fans are going to break?? will they?
longjohnsilver360 1 year ago
Running the fans a 12v will not break them, they were made to run at that voltage, Microsoft just ran them at 5v to keep the system quiet.
Omari1125 1 year ago
@Omari1125 leeching power off of your dvd drive however causes power fluctuations which can lead to a fried pcb, a broken dvd drive or a wasted power brick.
miasmablk 1 year ago
can you show us how to install an ac unit it our xbox 360's? o_O
RAM4486 1 year ago
Yes sir this fixed all my overheating issues, thanks so much :)
zhorax 1 year ago 8
I shall use this mod and i will win...retaliation microsoft...RETALIATIOOOOOOOOOOOOOOOOOOOOOOOOONNNNNNN!!!HAAAHAHAHAHAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA!!!
donda2111 1 year ago 15
is the myth true, that if u do 12 volt fan mod, microsoft can u ban for doing this
408427 1 year ago
@408427 Wait what?R u serious?Friggin microsoft.They just dont like how they didnt get the credit for fixing the RROD themselves so they make other people pay for taking away the spotlight.Friggin corporate scumbags... >:(
donda2111 1 year ago
@408427 i dont know if this is true. just a myth
408427 1 year ago
thank u very much for the shrink tubing idea. thats a big help
kaiba1977 1 year ago
Alright sorry for bad spelling i was on an ipad!
So if you do exactly as the tutorial shows it will work!
problem i encountered>>> When i turned on my xbox I'd get the 3 RROD so what you have to do to solve his problem is to turn around your dvd drive cable(black one) and try to turn on XBOX again! it will work like a charm!
Thanks for great tutorial!
pynn101 1 year ago
Sprint guys just did it and had one problem but it's solved! If you your DVD drive power cable backwards your fans won't spin and you'll get the 3 RROD. So all you have to do is turn around the DVD drive cable ( black one) and it should work fine!
pynn101 1 year ago
I have a weird problem. I managed to overload the source output for the fan, so I blew up the transistor. I can't use that power source. My fan is a talismoon whisper legacy which now runs at full speed with the DVD Drive as a power source. When I have this set up, my xbox 360 won't boot up if I'm using a hard drive. Can I fix this without soldering?
evenk93 1 year ago
Would this mod still work if i just used regular earphone wires to connect the other wires? or should i go to a hardware store and buy speaker wire?
phobix33 1 year ago
@phobix33 Im pretty sure its all the same
CreditedBag 1 year ago
Cheers, Just done it and is working perfect
hornerap01 1 year ago
Bro this is a huge fail, im lucky I undid this and did the one xboxsarerepairable did.
Avetsuga 1 year ago
Thank ya saved me bro.
Avetsuga 1 year ago
Will somebody please reply to this
When i turn on my xbox the right fan ( the closest to to the power input) is not spinning will this mod make the fan spin again
hacker536 1 year ago
@hacker536 you need to change your fan
philz02 1 year ago
@hacker536 no
IThurts2J1zz 1 year ago
Thanks!!!!!!!!!!
spy4561 1 year ago
who ever came up with this idea is F****N smart. most simplest and safest way to run the fans at 12 volts. beats all other tutorials that ive seen. smart thinking bro...
blackeye09 1 year ago
Lmao you just showed me a new way to strip wires! thanks Awsome vid!
AeolusCE07 1 year ago
which wire did u cut when you cut the black wire
Goog2904 1 year ago
HAAAAAAAAA man got some balls!!!! i use lighter too but i dont grab melted plastin i wait it to get cold and crumble it of
tornadexx 1 year ago
Just wanted to thank you for the lamen video on fixing fan problem. Your video got my family of "xboxers" up and happy again! Thanks a lot again!
ideaking76 1 year ago
Can anyone tell me what wire i could use?
xSaVaGeHoUsE 1 year ago
@xSaVaGeHoUsE I am sure any wire you have should work
pattyaaron 1 year ago
It's not a rrod fix it just prevents it. The stock fans are 12v fans but they are running on 5v by doing this they run at their full potential thus keeping the xbox cooler stopping it from over heating and damaging the joints between the cpu and the motherboard and the gpu and the motherboard, meaning no Rrod. If your wanting to repair your rrod 360 its really not hard. I bought an xclamp fix kit from ebay and followed one of the many tutorials online then reflowed the main chips with a heat gu
bailey734 1 year ago
i did everything correct and could hear the sound very clearly..and the rrod stil there..
visurajen 1 year ago
Comment removed
visurajen 1 year ago
uh which side of the dvd connector has the 12v wire? lol
spiritro06 1 year ago
Well this does make your xbox use even more power, as if it wasn't a power hog already...
LifeLongRacer 1 year ago
GOOD WORK AND THANKS ALOT!!!
norm51167 1 year ago
thank you man :)
nicolaiaquilina 1 year ago
@hackingjungle what if u dont have shrink tubing
boboonaboat 1 year ago
lol i like how this guy make i with things laying around
MetalMonkeyStudios 1 year ago
it work great fast easy and great tut
TheNicktito 1 year ago
HOLY SHIT - you are better than MacGyver and the A-Team together!
Good job!
OWNAveal 1 year ago
@Teeorie1 wooooow u r sooo fucking retarted it cant make your xbox hoter u dumb shit
buddylikeguitar 1 year ago
Thanks man my xbox was being weird the audio wasnt working and my fans stopped working so i took off the heat sinks and cleaned the cpu and gpu that fixed the fan problem but not the sound so i decided to give this a a try and now i got my sound back so i guess the cpu and gpu were getting to hot and this mod keeps the heat sinks cool you saved me from buying a new xbox thanks :)
UnluckyE 1 year ago
not saying that your method doesn't work, but definitely a different way of cutting and stripping the wires lol.
RiVaLSSJ 1 year ago
i ust bite the wire softly lol to get a nice cut :P
TanabeDrifters2010 1 year ago
shit i use a lighter 2 fkn wire cutters dnt work
559MODS 1 year ago
i heard this mod makes the xbox360 run hotter is this true
TexasproXmods 1 year ago