4.4 LPM hydrogen generator Customer Video

[makoshark26]

With that much output we can make a powerful hydrogen bomb ;)

[coffer782]

I've seen a lot of gas production tests most of which you cant see the complete bottle.....could be lying to sell units........yours is 100%. No faking gas displacing water and pushing the gas down and out of the bottle. LOVE the monster cell! Keep it up!

[eccentricgasman1964]

Incredible. I strapped three 40 plate generators to the front of my truck and couldn't pump out the amount yours does without it aventually over heating. WHAT AMOUNT OF AMPERAGE IS THIS MONSTER CONSUMING? And I couldn't say it enough:INCREDIBLE

[sovereignenergy]

40-50 amps

[redclaw4444]

Yeah question. What grade of Stainless steel do you use? 304, 316? gauge? where you bought it from too? Thanks and your cell is looking pretty good.

[sovereignenergy]

316L only!!!

[ExtremeHydrogenLabs]

also i have a hard time believing that it doesnt run hot...thus injesting steam wich causes a number of problems like engine damage,by the way how are controling this pig ??? my cells ARE controlled AND run between 95 to 130 deg. AT 20 to 30 amps.one of my show 95 deg.at45 amps for 4 hours WITH a cooling sys.

[sovereignenergy]

No steam and No Heat Problems! please don't confuse us with inferior submerged cells :)

[ExtremeHydrogenLabs]

i would like to see amps and temp.

[ExtremeHydrogenLabs]

i would like to see amps and temp

[Leftwings22]

Wow.  Just build it. And build it safe.

[variablestatus]

great cell design... can you show us a clamp-ampmeter on the power source so we can calculate how much hho might one get with lower amperage usage. i'm sure this cell has great production even at lower amperage usage. i would have really liked seeing the amp draw in this video with the bottle filling with hho. keep up the good clean work on the installs...5*'s

[milacute04]

i thought putting too much hho into the car will damage / not be so good for the motor??? can someone tell me whether more hho is good or bad.. thanks

[Rain4Fuel]

that's a myth

[alexetadv]

for 4.4LPM how much amp/volt???

did you use a PWM on this system??

what about cell temp???

Thanks

[sovereignenergy]

13volt under 60 amps no pwm and no heat problems.

you want 176 degrees F

[zerofuels]

this is a lie. In your other explosion video you are drawing 65.5 amps and fill 1 liter bottle in over twenty seconds according to timer at the bottom of video. You have to be pushing over 65.5 amps here. Your credibility keeps faltering sir.You lost my sale. I will not purchase from a lier. Shame on you.

[sovereignenergy]

Hi again zerofuels ie Ardentscientist

[etbalpha]

If you notice in the other explosion vid you are refering to the cell isn't installed in the vehicle, the wires are clamped on via jumper cables, just to fill the bottle not show a lpm test, jeez, what a flaming spammer, makes double accounts just to flame..ardentscientist/zerofue­ls, why aren't your bolts through the plates, aren't you worried about the plates shifting about over time and making contact? are you customers aware of your design flaw? and lack of craftmanship of your homemade cell?

[alexetadv]

i see you didn't use a flashback arrestor on your system!!!

it can be safe also?!?!? or not necessary with a second bubbler?!?!?

Thanks

[sovereignenergy]

a bubbler is a flashback arrestor. with a reservoir and a bubbler i think you would be more likely to get struck by lightning than get a flashback from an EFI!

[argosy2006]

who fitted ejector seat to ur bicycle and have u ever had to use it,boo yaw

[hydromaniac928]

I haven't had to use it, thanks for asking!

[sovereignenergy]

lol none! The generator wasn't even warmed up yet.

[hi5tech]

hmm how much of that output is steam? just a question.

[hydromaniac928]

The vapor has been eliminated by a second bubbler. We have the water too high in the water tank and some of it was getting into the first bubbler. It still produces the same LPM.