CLIP2

[Bullshitfinder1]

The device does not work, your calculations from you metering system is incorrect due to the pulsed signals being fed into them.

If this worked like your explaining, you would be able to make it self run, "but you can't, can you". It Does Not Work,

By the way, simplify you explanation, Take a breath of air occasionally,

I applaud you for trying.

[shahidaliable]

He is disproving the law of conservatoin of energy

Energy can be convertable into other forms but cant be produced

[frank0067]

i want my meter to be.. dam slow.. too

[UltimateRevenger]

release it before you die

[asteroceras]

@UltimateRevenger Better he dies before it's released.

[wilatemodel]

...Thank you,...come again!!........

[winsonal]

dear all

this device is not for sale yet

[asteroceras]

@winsonal Perhaps because you would be liable to go to jail for fraud?

[gl4sz]

Dear Winnsonal could you tell us in more details how your gen works?

I see there big capacitors and I started to wonder... please correct me if I'm wrong - the power meters work with Active Power (from well known power factor) right?

So if you can shift from Active Power (mesured in Watts) to Reactive Power (measured in VArs) the power meter will slow down, even if the power consumption will be the same, right?

[conandrum74]

how can i get in touch with you my friend?

[conandrum74]

how do I contact you mate? please send me your email.

[TrutherD1]

Google: scalar wars mysteries

[rekavardar12]

hello its ok this but i like to ask this inventor what is the frek. of this in out where is bulbs and howis look like the out voltage in the scope .BUT THIS IS GREAT DEVICES i askthe inventor there is important frek there in the out bulbs time pulsing is important if the time is low then... if the time of pulsing in bulbs is 50 times in one sec. then is ok anyway this is great if this is show here <but ask the inventor to show the scope voltage in the bulb if like to show THANKS

[carbonccc]

I would call it a Solid State Generator.

[trickyricky2009]

I too would like to experiment with your fine device in my home and shop.. nice work!!

[tomcon1001]

Hi Winsonal. Looks like great work to me. I would like to review one in my home, and I sent you my email address so you can contact me. Very exciting! Thank you.

[FiniteTuning]

Nice "resistive" demo you got there, and nice "joule thief" as well. I'd like you to run a 4' base board heater from your device at full power, then run a 5 HP motor as an inductive load. Resistive loads using light bulbs are easy, any joule thief can do that, but impress me with some inductive loads please. Light is too easy! That's why everyone uses light bulbs to demonstrate. Show "real power" by showing a 15 amp current draw, then I'll be sold! But it's still a nice "JOULE THIEF", good job!

[teslanumbertwo]

inverter?

[winsonali]

@teslanumbertwo

no its not an inverter its a motionless electric generator

[taicheee]

salamunalaikum Ali bhai, this is asif rizvi... seems its really nice work so far whatever you've done... wish you best of luck..

regards,

Asif Rizvi

[gabydewilde]

your camera man destroys your credibility by zooming out on the moment we want to see the meter and pointing at the meter while you are re-connecting the device.

You only get one chance at a first impression.

You also have your plugs the wrong way around. The male plug should be the consuming end.

You need to make a new video and get it right.

Good luck,

[gabydewilde]

ah, now I see it is the extension cord.

Forget about the last bit.

[MrFinsaan]

don't delay the device and open it for public otherwise you will not be able to help humanity

i suggest that if you cannot open the circuit till you get the patent share this with different clients or regional distributors so you will not remain bound to any one company or group

this product can be used with many applications i would like to buy one for what ever price you have in your mind coz this will help you in further development

i wish you best of luck for your achievement

[orangedac]

Whenever I get excited about such inventions, they turn out not to be all that's claimed on closer examination.

I'm hoping he will make the plans public so the claims can be tested.

Otherwise these inventions just get caught up in controversy and end up falling by the way side.

[M3anbone]

You should do humanity and the environment a favor and just release the information on how to do this --- the current corporate powers in place around the world aren't going to just let you put them under with your device.

[alinafame]

Ali bravo you have done it i know you since 1990 when u were chief Engineer in LG then you started your own TV manufacturing , you did wonderful project in your career ,

Like digital satellite receiver , Caller line identification system , Vessel monitoring system , vehicle tracking system , SOLAS safety of life at sea , encryption system, digital UPS system , you developed companies like WINSON from scratch , now you are doing these alternative energy projects bravo,

Wish you best of luck

[comwarrior69]

i think i might know how you get such a reduction in power...

However, that third wire concerns me too...

I'm also puzzled as to why you need a 30 volt input...most devices use a multiple of 12... so 12, 24, 48, 96....

Solar panels and wind power is mostly 12/24 volts... not 30...

[tomsmitsy]

Hi Ali, did you ship any samples yet? I have send you an e-mail because I am interested to do business if this works as you demonstrated

[winsonali]

no i haven't sent any unit yet coz i am in middle of developing the DC input section and that will be easier to use once i complete that unit i will respond to you

[tomsmitsy]

Hi Ali, thanks for your reply.

Looking forward to further discuss your technology.

Success in finalizing the DC version.

TOM

[rauf82]

dear you can't explain  about 3rd wire, why it connacted to your device?

[winsonali]

the device operates at 12 volts for its IC to operate it require 12 volts DC at 0.25 amps the third wire is 12 volts supply

system is under development so we have provided this supply externally once we finalize we will built it in side the unit

[evobennyevo]

I too would like to purchase one of your units to test, please email me details of payment method and cost.

Many thanks,

Ben.

[winsonali]

please send me email as given in video info

[12raullt]

I would like to purchase one of your devices to test. How much would it cost and where do I send the money. Please email me or I can call you

[winsonali]

this is my first post on you tube i have got a very good response unfortunately i due to lack to resources i can't produce good qty at this moment

i haven't fixed any price coz its not yet ready for home or commercial user i was looking forward to give unit to like minded people for testing purpose free of cost, a donation for the cause may be appreciated any way i am in a difficult situation to select among very fine knowledgeable people to share the device i will respond to you very shortly

[12raullt]

Any idea of the ocst yet? And how do I send the money?

Thaks

Raul

[DerrickA4mag]

@winsonal

Are you familiar with Power Factor? Most common electrical meters will give incorrect readings AC readings when current and voltage are significantly out of phase, or if power is being drawn at higher frequencies then the meter was intended to measure. I am just trying to establish your experience level with electronics, and if you are making a

fairly common (but understandable) measurement error.

[winsonali]

i do know PFC very well both ACTIVE and PASSIVE this is the reason why i measure the input output current and voltages and establish the fact on the basis of those elements use of meter is to show the reduce billing

coming to the point that the load i have used in the video is purely resistive which exhibits a 1.0 PF(power factor so there is no distortion of phase and in our final design definilty we will include passive componenets to counter measure PFC issues

[BhdRoussos]

@winsonal

I see a few setups consisting of inverter, battery and battery charger showing up in youtube. The creaters of theses videos claiming to run a fan and to recharge the battery .

This setup seems to work .

[markdansie]

I have tried emailing you please reply,

Just one question what power does it rquire to power the device, you have a cord going to something on the floor.

Fianlly is this scalable?

mark

[winsonali]

the device require 12 volts at 0.25 amps to activate the circuit the cord is providing 12 volts supply we have sofar tested unit till 1000va

the device is MEG this means motionless electricity generation

the beauty of the device is it can be used as voltage stablizers

it can directly connected with windmill and solar panels and you can remove battery banks from them

the principal of device is just like negative resistor but with a different technique

it has a progaming chip in side

[overunitydotcom]

Hi you should better rename your device

as Tom Bearden probably has a trademark on his MEG, which is a completely different principle.

Maybe better name it Negative Resistance Power Switching Device ( NRPSD) or something simular...

Hope this helps..

Regards, Stefan.

[overunitydotcom]

Looks great !

Can you already show a selfrunning system ?

Is this exactly the same design as Bearden has or modified ?

Many thanks.

Regards, Stefan.

[winsonal]

====So how does this invention work ?

it works through software and follow a patern of switchinhg technology which boost the voltages from 30 volts to 220 volts but reduces current

during the process the the movement of electrons generates its own rersonance and a more power out comes out

the principal is some thing like negative resistor but the technique used is different

this is my own theory which i have converted into practical means

[overunitydotcom]

I see, many thanks for the infos.

Do you also have coils in the unit ?

So do you switch the rectified AC into LC tanks and get then a higher voltage at resonance

that you feed to the bulbs ?

Do you have at the output again a pure 50 Hz sine wave of a different frequency and waveform ?

Many thanks.

Regards, Stefan.

[Cloxxki]

Can you place 2 of them in series, and re-route 1.5A/30V back to source, and use the remainder to drive a load?

[winsonal]

i haven't tried this way but i think it will not work as we are providing 30 volts A/C and producing resonance and due to this factor it will canel out effect if it is refeeded