Pulse Motor (Back EMF) 002

[kirbymelton23]

Your video is a favorite on Naypyidaw

[Ba55taztic]

list of supplies and where to buy them?

[AccessNo]

After this, the world as we know it will never be the same again :))))))))))))))))) OMG dude you gotta be related to Nikola Tesla

[pyronathanpyro]

do this in an elcetrik car

[Digadogup]

SKIP THE AD 0:01

[zach31992]

so its like a brushless motor but with only 4 magnets?

[vexedrex555]

your a tool

[capacitortube]

it is nothing new. just wasting energy

[alfredwindsom]

Pulse motors are interesting but the energy you make is always smaller than the energy you put in the sistem

[daeamarth]

And you just discharge X-Y number of batteries where Y is the lose of energy due to friction in your system let alone the loss of your inefficient human body pressing a button. When you figure this out I want you to push my car to work and back so I save gas and then not complain when you starve to death tryign to eat the same amount of food as you did prior. Basic 6th grade physics. FAIL!

[kubikop]

Thanks for watching, but I am not pushing your car. I'll PASS you bye!

[MrThomassss]

use a reed switch (bitch)

[smoothcriminaization]

Thats what I did later

Check out Videos 8 and 9 (hoe)

[Demoman42]

I having problems with coil, i think..

[kubikop]

Try holding a compass by it...

[Orcinus24x5]

Using back EMF to recharge a battery will actually -reduce- efficiency, because any significant current draw on the secondary coil will slow down the motor. You must convert kinetic energy to extract electrical energy, and this is why the motor would slow down. The reason it doesn't slow down with the LEDs attached is because they do not draw a significant amount of current. Ever try to turn an electric motor by hand with the coils shorted out? It's much more difficult than with an open-circuit.

[kubikop]

I think you might find that the Flyback voltage is usually grounded, zero back.

But thats for the comment the later videos are better....

Paul..

[bl444444444444ck]

dude that thing is crap ..

[kubikop]

dude what thing is crap ??

[darrelleric]

what did you use for the core????

[kubikop]

It is an Air Core.......

So I uses nothing for the core just air....

[Hexpigge]

nice job! :)

[kubikop]

Thanks

[Cryptoz4]

VERY EFFICIENT .. not lol

[kubikop]

?? Not a laff out loud, very efficient ??

[benchmark1954]

oh i forgot , i presume the battery is a re-chargeable battery and 6 volt. ( im under the impression that if it isnt a re - chargeable it will explode at some point.!.

[kubikop]

Yes... ;-) although I do a video recharging 9v standard batteries

[benchmark1954]

What is the size of the copper wire in "mm" in 'video 2 . tks

[kubikop]

Its 0.125mm Magnet wire

[Sh4n73c]

How about a little magnet-switch at the other side (every time magnet goes past, it turns ON or OFF)

[kubikop]

Look at video 8 and 9....... great minds think alike...

[bocatablanco]

you need to use a 555 in the zone of the switch xd

[petefabz]

if you were to use a micro-switch timed up to turn on every time the coil is over the magnets, or slightly past it on the disc, the disc should continue to spin until the power runs out.

[kubikop]

Thanks for the comment.

I used a reed switch in the end, and then a sensing coil.

Paul.

[kiev786]

this system work with only low power,we can't use it for higher power

[luckyelle13]

The back EMF that lights the LEDs comes from the coil itself, and not from the spinning rotor. Take the coil away from the motor and flip the switch and the LEDs will still light up.

[kubikop]

I know, the rotor is used for timing.

[Nabo00o]

Incredible work!

Must be the simpelest circuit i have seen yet, and thats good if you want more people to understand it.

[stallman76]

you didn't need the disc with magnets. The disk is nothing more than a timing device. You were doing all the work with your hand switch. Its all about the collaps

[BasementBen]

But later, the magnets have momentum to generate extra power?

[Meskalitto]

Haven' you heared of Bedini's SSG circuit. That is all you need, it will charge your battery with BEMF and is also self triggering. All you need is one transistor, two diodes, one resistor and one variable resistor. And the coil must be bifilar. Please find the Bedini_monopole3 group in Yahoo groups and you will find the schematic. I have built two of them, works like a charm.

Hope it helps.

[kubikop]

I will have a Look, Thanks for the help. Got a reed switch today and it spins very quick will upload soon.

[Juthumheim]

Use a 555 timer for the on/off swiching instead of that lame hand swich .

[kubikop]

Hi

I tried that but a reed switch works better.

Look at Pulse Motor 008 it gets some speed up!!

[hoekf]

Maybe use a Reed switch...like those on windows alarms?

[kubikop]

That is a good idea I will buy one and see if it works. Thanks.

[dumalucky]

So you are using energy from the magnets to recharge the battery? Am i correct?

[kubikop]

That is my end goal. I need to make more Coils though.