@faceless2103 I'm not too sure of the parameters, and I sold my unit a really long time back. Look through the comments though. I'm sure there are a couple of posts I've put up about the parameters for the sounds you liked.
I need help......it seems that when I plug my Korg AX3000G straight into the back of my computer, I have to crank the pedalsl volume all the way up to barely hear anything at all, and thats just using my patchcords....Is this normal or am I missing something?...please help
Hi, I would like to know how did you get the "Rock lead tone". Could somebody tell me which Config do I have to put in my Korg AX3000g to get this sound?
guys, i got mine a year ago.plugged it into a spider III 30w amp. what bothers me is that after plugged thru the korg ax3000g, my guitar signal from the amp seems to be like "choked" and the tone kinda diminished especially with distortion. the sustain seems to get shorter too. with my guitar plugged straight to the amp without the pedal, the sound was alot more "out there" and sustain was longer. is there any way to solve this problem? thanks guys!
@agentelectric I don't know how it can sound 'choked', but I can tell you that if your sustain seems to cut off, then, your noise gate settings may be high, and you'll need to cut back on the noise reduction. I'm trying to see how it can sound 'choked' as you put it...because its never happened to me. Can you post the settings of the patch that make it sound choked?? Maybe if I see the settings, I could help you a bit more.
@getvicky13 thanks for the reply m8. well urm, i run my guitar thru the amp without the pedal, the sound i get is thicker tones, richer harmonics whereas thru the pedal the sound got weak (less sustain & thinner tones). i was thinking the same thing so i shut off the noise gate but although its slightly better, its still not as good as when i had my guitar juz straight to the amp. i guess an example would b that when i pull a divebomb the sustain was alot weaker when i had it thru the pedal.
@agentelectric Of course...its always the best thing to do to connect straight to an amp with a few pedals :) There's no signal loss at all that way. And again, I'd like to see your settings, because I've done divebombs too back when I was younger, and its never cut off for me!
@agentelectric Bro, check if: your output knob is turned all the way up to the "amp" part on the back of your processor..that solved the same problem I had...In that way you have the full sound. Unless done so, your processor lowers the guitar signal and sends it to the amp...another thing you should check is that whether your volume/gain settings are set to some low value...that can also be problem, but if your output is to the max, volume should be around 12 o clock, and not over...
@AHMADF93 Its never happened to me while I owned this unit. I did have problems with the footswitches though. The contact switches inside can get worn out. Luckily, I had them replaced in a local electronics store. The output of this unit is really good! It takes time to get a decent overdrive tone on this. Try using the Boutique OD drive model, along with some cab modelling. The cab modelling really has an impact on the final sound.
Hello how are you, I have a korg ax3000g But Do Not Understand how to fix the effects, I wonder if you Could help me and tell me how to fix the effects I liked a lot, really thank you very much beforehand pardon the spelling
please look through the comments on the video. I've given a rough setting for those patches. I don't remember the exact settings because I sold the processor a really long time back.
i just received this processor, everything alrite wid it, i'v bin able to customised my own patches.. the only inconvenience am having wid it is that wen am playing, the sound as if cut off and then comes back and again goes out.. wat u guys cn suggest me to eradicate this damn trouble?? plz do response.. I'l be using it live very very soon. tnx
If your processor is working fine, then i dont think there's a problem with the unit. Check the output jack on your guitar, check your guitar cable, and check the soldering inside the guitar. There may be some loose wiring inside your guitar that could be causing the trouble
@abishua13 I'm experiencing the same problem in here!!! When I put my guitar to the amp only I don't get the problem...should I send it back while I still have warranty on it??
@TheUnforgivenGenius hi buddy, i no more get that prob now.. but i use it mostly on sundays in an air conditioned hall. because of the way things are done by air conditioners, i have z same prob.. but i'l be using a UPS soon, they say this will stop z cut.. else wen i use it at home, its working perfectly. try to connect it via a UPS(uninterrupted power supply)
@abishua13 I have finally figured out what is causing this!!! Some amps can't handle the amplified sound of the guitar from the processor so the get over-heated and they stop sending signal until they chill out a bit.... just don't krank the output volume over 12 on ur processor and you should be fine...
@abishua13 Hope I helped :) The same thing happens to me when I plug in processor on my line6 spider iii 30 watt...but using same amp just spider iv, the problem is gone....
not really. i was quite a beginner when i made this video. and i havent really used wah much since anyway. getting a new wah pedal, so hopefully, should get to play around with it a lot more and develop a good wah technique.
@getvicky13 but youre good man. i just didnt feel the vox wah that much. but overall rating i'll give you a 5stars. thanks for the demo. \m/ by the way, how much did you buy the korg ax3000g? because i'm planning to buy one
65 amps are great amps! i don't know why you use the processor with this amp! your amp loves pedals. i'm sure you might have watched the videos put up by proguitarshop. they almost always use 65 amps for their demos.
i don't know if this might work, but run your processor into the effects return of the amp. use the effects return instead of the guitar input.
Ok thank you for the response say me I have a guitar they paul with tablets emg, you believe that if I put these effects they are listened equally?? And if it(he,she) is that if wherefrom you extracted them?? Can you facilitate them to your me??, regards.
It will sound even better, since you have a better guitar, with really good pickups. And i don't have this processor anymore. I sold it more than a year back. sorry.
Ok gracias por la respuesta dime tengo una guitarra les paul con pastillas emg, crees que si pongo estos efectos se escuchen igual?? y s ies que si donde los sacaste?? me los podrias facilitar??, saludos.
I'm sorry, but i don't understand spanish. For the previous message, i used a google language tool to help me out. It would be great if you could comment in english.
Hey man, where I can found the: acoustic simulator, hard rock distortion, high gain rhythm tone and the high gain lead? In what numbers?? I like your guitar style!! you are good
hey man i just got this pedal and i dont know how to do half the stuff or make it sound how you do and what somethings do, can you explain to me the basics of this and what something are used for
hey bro..thnx a lot 4 tking time and helping everybody out..i jst got the ax3000 and am not satisfied with the dist..i need a more heavy sound so wud a Boss DS1 or anyother pedal work fine with the processor especially for sustaining solos and stuff..thx
hey man...i tried putting a DS-1 too. i dint get very desirable tones, but maybe you'll get something better. and you say that you've just got the processor. try spending some time with it man. you might end up with an awesome sounding overdrive that you can even use for stuff like old school metal, like megadeth and maiden. and for sustaining solos, try turning on the compressor, some reverb and delay.
in the pre fx section, you can choose the compressor. you have basically two parameters in the compressor - sensitivity and level. i think the level parameter is basically the output volume of the compressor, and sensitivity controls the amount of compression.
Hey Vikram, Uday here. Watching the video after a really long time, the riff you played for the crunch tone is the riff for One Night Stand righT? Man i just love that song! Awesome!
yeah..i think you can get pretty close. you'll have to assign the expression pedal on the AX 3000G to control the pitch on the pitch bend parameter in the modulation section. i think the pitch is set to go one octave higher. not too sure though, and for the amp model, you'll have to use something high gain. like the metal dist model.
not sure about the infinite delay bit, but if you want really long delay sounds that hold on for a long time, try pushing your feedback control to 10.
i didn't take too long actually. i think i posted this video quite a few months after i bought the processor. and i just trusted my ears. thats about it. you just need to know what effect does what. and dont go by the names given for the drive parameters. just turn the knob until you get a sound thats close to what you want, and then tweak it till you zero in on what you exactly need your tone to be like.
try and go for a line 6 pod xt live. i dont know abt the floor pod plus, but a friend owns and one, and maybe its just him, but i havent heard many good tones from it. depends on what you play..the korg ax 3000g cannot handle extreme metal sounds.
well, if there's a database of patches uploaded by someone, you can download them. but i have never really come across something like this, and even if i did, i wouldnt have downloaded a patch.
well, i did not record direct into a DAW, and i did not use a professional mic (not even an SM 57) to record the sound from the amp. And i did not record it in a studio which has controlled acoustic conditions. I did it in my bedroom with a desktop microphone in front of my marshall. Its also possible that it sounds like that coz i've used a bit of spring reverb in all the patches.
hehehe! yes it is! am glad ppl still listen to mr.big. btw, they are reforming. the original line up, with paul gilbert, eric martin and billy sheehan. forgot the drummer's name...
i used a very old computer mic that i placed in front of my amp. you'll need an external recording interface like an m-audio fast track pro or presonus firebox to use a spdif cable for recording.
maybe it will. if your computer has a line in jack, it should work with a software like audacity or something. i've never really tried it, so i cant comment.
no it doesnt have a drum machine or a metronome. between a digitech gnx3000 and a korg ax3000, maybe you could go for the digitech. depends on what you play though. i have heard that digitech with distortions. dont expect extreme high gain possibilities from the korg. it just wont. i used the korg more for its clean tones and its overdrives.
the gnx4! i dont know if it have a metronome or drum patch but i know that you can record an mp3 in the memory and loop it, so if you use a record of a drum beat it can be a better option because it can give you more possibilities than the gnx3000 or the last rp model. i prefer the clean tones of the digitech and the distortions seems to be close to the korg, not as good but a good choice too.
Hey to every 1, I'm almost turning 16, in about a week or so, and i wanne buy a new effectpedal for my Epiphone les paul custom EB and my Marshall mg 100 dfx. I'm planning to pay 100-200 euro's for it. Any 1 has some nice idea's? i was thinking about the Korg AX 3000g myself.
But any other idea's are very welcome ;), thank you very much.
Since you're using a solid-state modeling amp, you will immediately benefit from a more versatile delay than what comes onboard. Delays are easily a more commonly used effect. You can then rely on your onboard phaser, flanger, and chorus. A new distortion would be nice too, but I'm not sure how solid state amps take to distortion pedals, but you can use your amp's clean channel. The nice thing about effects systems like the Korg is that you get room to explore and discover...
With pedals, you'll get better sound quality, however, you'll spend a lot of money as you move from pedal to pedal in order to find what you want. I wouldn't begin investing in pedals until you know precisely what sound you're looking for. And at your age, you should probably focus on exploring many different kinds of music, so guitar multi-effects systems are likely a better choice right now.
unfortunately, i dont know the settings for the wah parameter. i've even sold my processor. i've gone analog. but the amp model that i had used in the wah patch was a vox ac 30 with a decent amount of gain..
yes it can. can be connected straight to your recorder with the digital output, or you could hook up processor with a midi cable. of course, your computer or recording interface must have midi ports.
what do you mean by 'increasing the volume of a plain acoustic patch? you could either set the patch on a rather high volume, bring the pedal back a bit to reduce the volume and depress the pedal when you want it loud, or you can make another patch in the same bank, with a louder setting.
soft acoustic patch like floyd? try using a Boutique CL amp model, with some chorus, delay and a good amount of spring reverb.
depends on what you want to use man. if you're more of an effects user, go for the korg ax 3000g. but if you want more distortions and simple tones, go for the me 20.
i used an ibanez grg 270 and a marshall mg 15 CD for this video. and i used the power amp in for the demo.
i havent tried the vox tonelab, but i've heard good things about it. but if you want to play classic rock and blues, i really suggest you buy pedals, like a digitech bad monkey or boss super overdrive.
hi man i realy liked your demo please could you tell me how much does this pedal cost, because i from argentina and im going to have a trip to New York and miami and i realy want to buy this pedal but i cant find the price of this pedal could you tell me the price of this pedal in Miami and in New York ? thanks you very much
if you're into techno and stuff, this is brilliant. awesome clean tones and a lot of modulation effects. the effects are really good on this unit. although you wont have a slicer effect, its got tremolo, uni vibe, phaser, flanger, sitar, chorus, pitch shift and what not.
nope. i just placed a simple and very very cheap microphone(the type we use for voice chats) in front of my amplifier, and switched off everything that moves inside my room. thats about it.
well, i guess you can get close with the Vox AC 30 amp model. I wont say that you can replicate tones, coz with any processor, you can only model the 'tone' of an amp, and not the dynamics of the amp. Simply put, you can sound like you're playing a Fender Bassman, or Vox AC30, but you just wont feel it.
dude i have one of these too please, please can u giv me the parameters u used for the acoustic the clean chorus the mild/crunch and the high gain, please dude reply id really aprecciate man im a rookie guitar player looking for a good sound
That's all the patches in this video, excepting the hard rock patch!!!
look around somewhere in this thread man. i think i've given some parameters here. besides, since you're a rookie, now is the time when you should really start trying to get your own sound. dont limit yourself to what i've done. figure things out for yourself man.
Very nice!!! Can you give me your presets for High gain rhythm tone and High Gain Lead??? It would be very nice...i have the board since a few hours...
Thanx very much....
snurf727 1 month ago
dude could you send me the last 3 cofig. per massage? I would be very thankful :D
faceless2103 4 months ago
@faceless2103 I'm not too sure of the parameters, and I sold my unit a really long time back. Look through the comments though. I'm sure there are a couple of posts I've put up about the parameters for the sounds you liked.
getvicky13 4 months ago
I need help......it seems that when I plug my Korg AX3000G straight into the back of my computer, I have to crank the pedalsl volume all the way up to barely hear anything at all, and thats just using my patchcords....Is this normal or am I missing something?...please help
snurf727 5 months ago
@snurf727 Dude try connecting the pedal to the usb of the computer through the interface.
256guitarhero 1 month ago
THANK YOU getvicky13!!!!!!!! I will get this effect, and I needed this....... This video is very very good! Thank you!!
sampucni 7 months ago
Excelent Job!. Can you send me the patches please?
thepanflix 8 months ago
line 6 floor pod plus / xt live/ x3 live/ hd300/ hd400/ hd500 tienen la posta !!
zZCHELOZz 9 months ago
hey i've the same problem...but i have a Korg toneworks AX1G.
marcelot12 9 months ago
Hi, I would like to know how did you get the "Rock lead tone". Could somebody tell me which Config do I have to put in my Korg AX3000g to get this sound?
Brrrrrrrm 9 months ago
guys, i got mine a year ago.plugged it into a spider III 30w amp. what bothers me is that after plugged thru the korg ax3000g, my guitar signal from the amp seems to be like "choked" and the tone kinda diminished especially with distortion. the sustain seems to get shorter too. with my guitar plugged straight to the amp without the pedal, the sound was alot more "out there" and sustain was longer. is there any way to solve this problem? thanks guys!
agentelectric 1 year ago
@agentelectric I don't know how it can sound 'choked', but I can tell you that if your sustain seems to cut off, then, your noise gate settings may be high, and you'll need to cut back on the noise reduction. I'm trying to see how it can sound 'choked' as you put it...because its never happened to me. Can you post the settings of the patch that make it sound choked?? Maybe if I see the settings, I could help you a bit more.
getvicky13 1 year ago
@getvicky13 thanks for the reply m8. well urm, i run my guitar thru the amp without the pedal, the sound i get is thicker tones, richer harmonics whereas thru the pedal the sound got weak (less sustain & thinner tones). i was thinking the same thing so i shut off the noise gate but although its slightly better, its still not as good as when i had my guitar juz straight to the amp. i guess an example would b that when i pull a divebomb the sustain was alot weaker when i had it thru the pedal.
agentelectric 1 year ago
@agentelectric Of course...its always the best thing to do to connect straight to an amp with a few pedals :) There's no signal loss at all that way. And again, I'd like to see your settings, because I've done divebombs too back when I was younger, and its never cut off for me!
getvicky13 1 year ago
@agentelectric Bro, check if: your output knob is turned all the way up to the "amp" part on the back of your processor..that solved the same problem I had...In that way you have the full sound. Unless done so, your processor lowers the guitar signal and sends it to the amp...another thing you should check is that whether your volume/gain settings are set to some low value...that can also be problem, but if your output is to the max, volume should be around 12 o clock, and not over...
TheUnforgivenGenius 11 months ago
@agentelectric if you put some compression sustain becomes longer..sorry 4 my english :P
i use noise gate usually on 30-40 + compression with sensitivity on 75-85, level on 60-85...it works fine ;)
Sadly, compressor adds a little bit of noise that gate can´t hold without killing your sustain...welcome to reality hahaha
mmm maybe "choked" means asfixiated?? ^^
good luck!
veroSonica 10 months ago
how was your delay set on the high gain lead sound? delay type, delay time, feedbak, delay mix?
PeterOevergaard 1 year ago
Seriously I need the settings of the High Gain Rythem and Lead:O
RollingStoneSour 1 year ago
same for me dude!!
metalikaz 1 year ago
I've heard some complains about the "sound was cut off" while playing. Is that true? How's the output of this thing?
AHMADF93 1 year ago
@AHMADF93 Its never happened to me while I owned this unit. I did have problems with the footswitches though. The contact switches inside can get worn out. Luckily, I had them replaced in a local electronics store. The output of this unit is really good! It takes time to get a decent overdrive tone on this. Try using the Boutique OD drive model, along with some cab modelling. The cab modelling really has an impact on the final sound.
getvicky13 1 year ago
I need this crunchy tone you got in here...can u tell me the settings, or just email me preset if you have it on pc...thx :)))
TheUnforgivenGenius 1 year ago
Hello how are you, I have a korg ax3000g But Do Not Understand how to fix the effects, I wonder if you Could help me and tell me how to fix the effects I liked a lot, really thank you very much beforehand pardon the spelling
anikilador8 1 year ago
i dont like the sounds of this processor
jgimco 1 year ago
pls post the high gain rhythm tone patch....
Hunterhun92 1 year ago
please how do you do the high gain rhythm tone and high gain lead, could you send me the patches, the position of the tuners? thanks!!!!
Totote423 1 year ago
@Totote423
please look through the comments on the video. I've given a rough setting for those patches. I don't remember the exact settings because I sold the processor a really long time back.
getvicky13 1 year ago
@getvicky13 why did u sold the processor any probs ??
TheMagicalGuitarist 1 year ago
i just received this processor, everything alrite wid it, i'v bin able to customised my own patches.. the only inconvenience am having wid it is that wen am playing, the sound as if cut off and then comes back and again goes out.. wat u guys cn suggest me to eradicate this damn trouble?? plz do response.. I'l be using it live very very soon. tnx
abishua13 1 year ago
@abishua13
If your processor is working fine, then i dont think there's a problem with the unit. Check the output jack on your guitar, check your guitar cable, and check the soldering inside the guitar. There may be some loose wiring inside your guitar that could be causing the trouble
getvicky13 1 year ago
@abishua13 I'm experiencing the same problem in here!!! When I put my guitar to the amp only I don't get the problem...should I send it back while I still have warranty on it??
TheUnforgivenGenius 1 year ago
@TheUnforgivenGenius hi buddy, i no more get that prob now.. but i use it mostly on sundays in an air conditioned hall. because of the way things are done by air conditioners, i have z same prob.. but i'l be using a UPS soon, they say this will stop z cut.. else wen i use it at home, its working perfectly. try to connect it via a UPS(uninterrupted power supply)
abishua13 11 months ago
@abishua13 Hey bro, I sent it to the shop i bought it in...they 'fixed' it...it works for now :))) But UPS is really nice idea :)) Thanks bro! :))
TheUnforgivenGenius 11 months ago
@abishua13 I have finally figured out what is causing this!!! Some amps can't handle the amplified sound of the guitar from the processor so the get over-heated and they stop sending signal until they chill out a bit.... just don't krank the output volume over 12 on ur processor and you should be fine...
TheUnforgivenGenius 9 months ago
@TheUnforgivenGenius hmmm.. ok.. Thanks buddy :))
abishua13 7 months ago
@abishua13 Hope I helped :) The same thing happens to me when I plug in processor on my line6 spider iii 30 watt...but using same amp just spider iv, the problem is gone....
TheUnforgivenGenius 7 months ago
a payed 250 euros for korg ax 3000g two years ago, now is cheaper...
tintinexplorerbg 1 year ago
thanks for your video....i already buy this effect so i check every single video in this youtube..
zamri11 1 year ago
do you really know how to use the vox wah?
carpio18 1 year ago
not really. i was quite a beginner when i made this video. and i havent really used wah much since anyway. getting a new wah pedal, so hopefully, should get to play around with it a lot more and develop a good wah technique.
getvicky13 1 year ago
@getvicky13 but youre good man. i just didnt feel the vox wah that much. but overall rating i'll give you a 5stars. thanks for the demo. \m/ by the way, how much did you buy the korg ax3000g? because i'm planning to buy one
carpio18 1 year ago
hehe thanks a lot! i bought the korg ax3000g for about Rs.14000 (India). I dont know how much that works out in your currency though.
getvicky13 1 year ago
@getvicky13 does this have usb recording
helldx07 1 year ago
@helldx07
getvicky13 1 year ago
@helldx07 Nope :)
getvicky13 1 year ago
@helldx07 but the tascam dp-02cf does and its only worth £225 !!!
pugNdrum 1 year ago
@pugNdrum But I Got Myself a Boss Me-25 ..lol
helldx07 1 year ago
can you tell me the parameters that you used for create these sounds please?
1)high rhythm tone
2)high gain lead
i have it but i don't know how to create those fantastic sounds!! (sorry for my bad english)
giorgiopiraccini 1 year ago
nice patches man, i got this one too , but today i get an new amp ( 65 ) and it sounds like shit with it xD, this have fucked my day
xobrasxx 1 year ago
65 amps are great amps! i don't know why you use the processor with this amp! your amp loves pedals. i'm sure you might have watched the videos put up by proguitarshop. they almost always use 65 amps for their demos.
i don't know if this might work, but run your processor into the effects return of the amp. use the effects return instead of the guitar input.
getvicky13 1 year ago
Ok thank you for the response say me I have a guitar they paul with tablets emg, you believe that if I put these effects they are listened equally?? And if it(he,she) is that if wherefrom you extracted them?? Can you facilitate them to your me??, regards.
CRUZAGC 1 year ago
It will sound even better, since you have a better guitar, with really good pickups. And i don't have this processor anymore. I sold it more than a year back. sorry.
getvicky13 1 year ago
Ok gracias por la respuesta dime tengo una guitarra les paul con pastillas emg, crees que si pongo estos efectos se escuchen igual?? y s ies que si donde los sacaste?? me los podrias facilitar??, saludos.
CRUZAGC 1 year ago
I'm sorry, but i don't understand spanish. For the previous message, i used a google language tool to help me out. It would be great if you could comment in english.
getvicky13 1 year ago
Que guitarra estas usando? saludos.
CRUZAGC 1 year ago
Ibanez GRG 270
getvicky13 1 year ago
Does ax3000 have harmonizer?
GaljoTOTO 1 year ago
No. It only has a pitch shifter.
getvicky13 1 year ago
tres cool
Dadofbatskull 1 year ago
thank you man!!!!!! =D
TraceuRXusS 1 year ago
Hey man, where I can found the: acoustic simulator, hard rock distortion, high gain rhythm tone and the high gain lead? In what numbers?? I like your guitar style!! you are good
5 stars!!!!
TraceuRXusS 1 year ago
acoustic simulator - pre fx
hard rock dist - shred dist
high gain - metal dist
high gain lead - metal dist with some compression and delay
getvicky13 1 year ago
hey man i just got this pedal and i dont know how to do half the stuff or make it sound how you do and what somethings do, can you explain to me the basics of this and what something are used for
skate0rDi33 2 years ago
hey bro..thnx a lot 4 tking time and helping everybody out..i jst got the ax3000 and am not satisfied with the dist..i need a more heavy sound so wud a Boss DS1 or anyother pedal work fine with the processor especially for sustaining solos and stuff..thx
matli317 2 years ago
hey man...i tried putting a DS-1 too. i dint get very desirable tones, but maybe you'll get something better. and you say that you've just got the processor. try spending some time with it man. you might end up with an awesome sounding overdrive that you can even use for stuff like old school metal, like megadeth and maiden. and for sustaining solos, try turning on the compressor, some reverb and delay.
getvicky13 2 years ago
Comment removed
matli316 2 years ago
How do you tweak the compressor?
Dragonofkreation 2 years ago
in the pre fx section, you can choose the compressor. you have basically two parameters in the compressor - sensitivity and level. i think the level parameter is basically the output volume of the compressor, and sensitivity controls the amount of compression.
getvicky13 2 years ago
Does somebody know High Gain Lead settings?
ArsenyKorotaev 2 years ago
Hey Vikram, Uday here. Watching the video after a really long time, the riff you played for the crunch tone is the riff for One Night Stand righT? Man i just love that song! Awesome!
udayvirgarg22 2 years ago
hahahaha yeah it is the riff for One Night Stand! lol! I think i came up with this riff before the song was composed! lol
getvicky13 2 years ago
Lol. But i dig that riff man.
udayvirgarg22 2 years ago
you are very good my friend....and you got a very cool sound... with this pedalboard.... CHEERS 5 STARS
rdt78 2 years ago
Hey can you send me all of these settings? I've had soooo much trouble with this korg. It would be a big help! Thank you!
The0utreach 2 years ago
sorry bro. sold the processor a long long time back. check the comments here. i've given a few settings from what i remembered.
getvicky13 2 years ago
how can i make the acoustic simulator?? tell me please!
zupo27 2 years ago
in the pre fx section, there's a parameter by which you can use the acoustic simulation. its pretty simple really.
getvicky13 2 years ago
can i get the effect Joe sat gets on the song Searching with the pitch bend.
metalking40 2 years ago
yeah..i think you can get pretty close. you'll have to assign the expression pedal on the AX 3000G to control the pitch on the pitch bend parameter in the modulation section. i think the pitch is set to go one octave higher. not too sure though, and for the amp model, you'll have to use something high gain. like the metal dist model.
getvicky13 2 years ago
thanks, it would have been awesome if it had the loop like the AX1500 did, one more thing, can I get the infinite delay Gary Moore gets on Walkways?
metalking40 2 years ago
not sure about the infinite delay bit, but if you want really long delay sounds that hold on for a long time, try pushing your feedback control to 10.
getvicky13 2 years ago
fucking good job dude
aqpforce 2 years ago
WOW! can you tell me the setting for high gain lead?
LordAngelon 2 years ago
metal distortion drive model, compression, spring reverb, analog delay.. AC 30 cabinet
modelling.
getvicky13 2 years ago
wow.. say me please the clean chorus information!! *__* great sound!
maarcel12 2 years ago
i think its the AC 30 amp model with a bit of chorus and spring reverb. and preferably used on a single coil pickup.
getvicky13 2 years ago
Hey man please help
Should I use this or the Pandora PX5d for playing lead???(death metal / rock..)
Oh yeah and I'm gonna use it with my keyboards
Also does this thing have Bypass and Pitch Bend please help me man ....Would be very grate full if u did ..by the way ,Great playing man!!
CdPrni 2 years ago
hey buddy...i really dont know about the pandora. i've never used it.
and yeah the korg ax3000g does have a bypass and pitch bend. the pitch bend can be controlled using the expression pedal.
getvicky13 2 years ago
Thanks a lot man really
CdPrni 2 years ago
sounds good,but how long did you need to make all these patches,because i can't find sound which i want for months...?
wqenfgre348 2 years ago
i didn't take too long actually. i think i posted this video quite a few months after i bought the processor. and i just trusted my ears. thats about it. you just need to know what effect does what. and dont go by the names given for the drive parameters. just turn the knob until you get a sound thats close to what you want, and then tweak it till you zero in on what you exactly need your tone to be like.
getvicky13 2 years ago
What should i get a line 6 floor pod plus or a korg ax3000g??
solarmolar94 2 years ago
try and go for a line 6 pod xt live. i dont know abt the floor pod plus, but a friend owns and one, and maybe its just him, but i havent heard many good tones from it. depends on what you play..the korg ax 3000g cannot handle extreme metal sounds.
getvicky13 2 years ago
Is there a sound patch that i can download through the net to my ax3000g? plss help me
rersein 2 years ago
well, if there's a database of patches uploaded by someone, you can download them. but i have never really come across something like this, and even if i did, i wouldnt have downloaded a patch.
getvicky13 2 years ago
it sounds good, except, why does it sound like its coming off from a cave?
pinkybrief 2 years ago
well, i did not record direct into a DAW, and i did not use a professional mic (not even an SM 57) to record the sound from the amp. And i did not record it in a studio which has controlled acoustic conditions. I did it in my bedroom with a desktop microphone in front of my marshall. Its also possible that it sounds like that coz i've used a bit of spring reverb in all the patches.
getvicky13 2 years ago
ok, sorry dude, my bad
pinkybrief 2 years ago
Can i have your email? i have lots of questions XD
TheComingCurse666 2 years ago
i have this pedal, and im pretty sure it doesn't, unless im missing something, but can u record urself and loop it just using hte pedal?
MonkeyMike96 2 years ago
haha you're right. you can't record and loop on this processor. get yourself an loop station pedal from boss. the RC 2 i think.
getvicky13 2 years ago
does it have infinite delays?
WouterGuitarFreak 2 years ago
yes. if you put the feedback on 10, it will continue to hold the sound.
getvicky13 2 years ago
thats superfantastic ... !
baniero 2 years ago
hehehe! yes it is! am glad ppl still listen to mr.big. btw, they are reforming. the original line up, with paul gilbert, eric martin and billy sheehan. forgot the drummer's name...
getvicky13 2 years ago
sen me your patches? =)
Miza333 2 years ago
Pat Torpey! Better remember his name cause he´s the most talented of the band.
mtaygoldin 2 years ago
and, what amp did u use?
DarkmagicianOPV 2 years ago
its a marshall mg 15CD. i've mentioned so in the video :)
getvicky13 2 years ago
man, the sound is awesome , please send me your patches ...I need help
thanks
aqpforce 2 years ago
man, can you help me with the high gain lead? I cant reach that sound... could you tell me how to make that patch? also the rock lead please!
DarkmagicianOPV 2 years ago
high gain lead - metal distortion, spring reverb, analog delay, compression, and AC 30 cabinet modelling
rock lead - shred distortion, black 2 X 12 cabinet modelling, analog delay, compression and spring reverb
getvicky13 2 years ago
hey did you directly recorded to your computer? I have an ax3000g to and i'm wondering where i need to plug in an S/PDIF cable into my pc
unbornchild5 2 years ago
i used a very old computer mic that i placed in front of my amp. you'll need an external recording interface like an m-audio fast track pro or presonus firebox to use a spdif cable for recording.
getvicky13 2 years ago
do you think that it will work with a 1/8 to 1/4 inch converter, so i put in the ax3000g in my computer, where i put a micro in. ?
unbornchild5 2 years ago
maybe it will. if your computer has a line in jack, it should work with a software like audacity or something. i've never really tried it, so i cant comment.
getvicky13 2 years ago
sorry i mean 1/4 to 1/8 :)
unbornchild5 2 years ago
hey does it have a metronome and different drum patches and rhythms??
and if i had to chose between a DIGITECH GNX3000 n KORG AX3000G which one should i take?
kirkjames92 2 years ago
no it doesnt have a drum machine or a metronome. between a digitech gnx3000 and a korg ax3000, maybe you could go for the digitech. depends on what you play though. i have heard that digitech with distortions. dont expect extreme high gain possibilities from the korg. it just wont. i used the korg more for its clean tones and its overdrives.
getvicky13 2 years ago
the gnx4! i dont know if it have a metronome or drum patch but i know that you can record an mp3 in the memory and loop it, so if you use a record of a drum beat it can be a better option because it can give you more possibilities than the gnx3000 or the last rp model. i prefer the clean tones of the digitech and the distortions seems to be close to the korg, not as good but a good choice too.
RythmTR 2 years ago
Does the Korg AX3000G has a tuner??
guitarmaniacgino 2 years ago
of course it does. press and hold down any of the program footswitches and you're in the tuner mode.
getvicky13 2 years ago
Hey to every 1, I'm almost turning 16, in about a week or so, and i wanne buy a new effectpedal for my Epiphone les paul custom EB and my Marshall mg 100 dfx. I'm planning to pay 100-200 euro's for it. Any 1 has some nice idea's? i was thinking about the Korg AX 3000g myself.
But any other idea's are very welcome ;), thank you very much.
Scargon
Scargon1993 2 years ago
Since you're using a solid-state modeling amp, you will immediately benefit from a more versatile delay than what comes onboard. Delays are easily a more commonly used effect. You can then rely on your onboard phaser, flanger, and chorus. A new distortion would be nice too, but I'm not sure how solid state amps take to distortion pedals, but you can use your amp's clean channel. The nice thing about effects systems like the Korg is that you get room to explore and discover...
KeenAnthony 2 years ago
With pedals, you'll get better sound quality, however, you'll spend a lot of money as you move from pedal to pedal in order to find what you want. I wouldn't begin investing in pedals until you know precisely what sound you're looking for. And at your age, you should probably focus on exploring many different kinds of music, so guitar multi-effects systems are likely a better choice right now.
KeenAnthony 2 years ago
no pedals with an SS amp, multifx is the way to go, and especially you who you have an MG...Digitech Rp500 or Boss ME70..Check them out :)
k0staZ 2 years ago
mild overdrive / crunch what amp did you use it sound pretty nice :D
funkyfanta93 2 years ago
vox ac 30 and spring reverb.
getvicky13 2 years ago
you played really long on the high gain part. you really like it don't u? hahaha. nice vid. and great playing.
setalaka 2 years ago
haha all the riffs and solos in this video were made up in about a matter of 20 minutes. did not really bother to see which one was longest!
and thanks! glad you liked the video.
getvicky13 2 years ago
100!!
akane20080125 2 years ago
and how are the bass, mid, treble, etc.?
BmaN32123 2 years ago
dont remember dude. sold my processor in january.
getvicky13 2 years ago
This is great multieffect and you presented it very well! But i'm curious, what did you buy instead?
voltaspeeder17 2 years ago
i went analog. I bought a damage control tube preamp and a digitech screaming blues overdrive pedal.
getvicky13 2 years ago
Thanks :)
voltaspeeder17 2 years ago
what is the setting of the High gain rythm tone? i bought this effect yesterday, but i didnt find high gain
BmaN32123 2 years ago
its the metal dist parameter in the drive/amp section
getvicky13 2 years ago
your high gain lead was sick!
ApproachingByStealth 2 years ago
hehe thanks a lot! glad you liked it.
getvicky13 2 years ago
can you give me presets for the vox wah? appreciate it :)
dudokrs 2 years ago
unfortunately, i dont know the settings for the wah parameter. i've even sold my processor. i've gone analog. but the amp model that i had used in the wah patch was a vox ac 30 with a decent amount of gain..
getvicky13 2 years ago
heyyy chekc that video nice patches made...
goodrock20 2 years ago
what was the song you were playing for the high gain rhythm tone
hellchild101 2 years ago
that was just some riff i came up with...dint copy any song!! hehe
getvicky13 2 years ago
can the ax3000g be connected to the computer?
udayvirgarg22 2 years ago
yes it can. can be connected straight to your recorder with the digital output, or you could hook up processor with a midi cable. of course, your computer or recording interface must have midi ports.
getvicky13 2 years ago
hi can u tel me a way to increase volume of a plain acoustic patch n also how to make a nice n soft acoustic patch like pink floyd
deathmetallica2nd 3 years ago
what do you mean by 'increasing the volume of a plain acoustic patch? you could either set the patch on a rather high volume, bring the pedal back a bit to reduce the volume and depress the pedal when you want it loud, or you can make another patch in the same bank, with a louder setting.
soft acoustic patch like floyd? try using a Boutique CL amp model, with some chorus, delay and a good amount of spring reverb.
getvicky13 3 years ago
Very nice!!! Can you give me your presets for mild overdrive/ crunch???
jys8751 3 years ago
yeah..its a basic amp model. just turn up the gain on the vox ac 30 amp model. and use a bit of spring reverb.
getvicky13 3 years ago
sexy demo man...keep it up!
TamilMaskdotCom 3 years ago
can u post me the setting for th metal n rock patches u showd of rythm n lead
deathmetallica2nd 3 years ago
hey...metal - metal dist, AC 30 cab model and a bit of spring reverb. add a little compression and delay for the solo.
rock - use shred dist, blk 2X12 cab model, spring reverb. use compression and delay for lead.
getvicky13 3 years ago
guys what s better this effect pedal or a boss me20? plz tell me
dannyinajax 3 years ago
depends on what you want to use man. if you're more of an effects user, go for the korg ax 3000g. but if you want more distortions and simple tones, go for the me 20.
getvicky13 3 years ago
no way... korg is much better than the me series of boss..
udayvirgarg22 2 years ago
sorry for my english
joakorush2112 3 years ago
I'm sorry man. I don't know about the price of the unit in USA. I'm from India.
getvicky13 3 years ago
Do yoiu know how to sample and play on the korg? if you do can you tell me how to?
ironmaiden20 3 years ago
what's your guitar and amp? Are you using input or "power amp in" or something like that at your amp? (my English is bad sorry)
And did you tried vox tonelab? I want clasicrock & blues tone. Should I buy tonelab because of valve?
cihancil 3 years ago
i used an ibanez grg 270 and a marshall mg 15 CD for this video. and i used the power amp in for the demo.
i havent tried the vox tonelab, but i've heard good things about it. but if you want to play classic rock and blues, i really suggest you buy pedals, like a digitech bad monkey or boss super overdrive.
getvicky13 3 years ago
hi man i realy liked your demo please could you tell me how much does this pedal cost, because i from argentina and im going to have a trip to New York and miami and i realy want to buy this pedal but i cant find the price of this pedal could you tell me the price of this pedal in Miami and in New York ? thanks you very much
joakorush2112 3 years ago
How are the effects man?
Apart from distortion, are there any techno effects in it? I heard it has a sitar effect?
I'm into electro-funk
PhobiaTheBand 3 years ago
if you're into techno and stuff, this is brilliant. awesome clean tones and a lot of modulation effects. the effects are really good on this unit. although you wont have a slicer effect, its got tremolo, uni vibe, phaser, flanger, sitar, chorus, pitch shift and what not.
getvicky13 3 years ago
Thanks a bunch brother!
:)
PhobiaTheBand 3 years ago
Dude, how do you record it in such good quality?
Do you use a Interface or something?
hamdengo 3 years ago
nope. i just placed a simple and very very cheap microphone(the type we use for voice chats) in front of my amplifier, and switched off everything that moves inside my room. thats about it.
getvicky13 3 years ago
can u help me with the patch settings for korg ax10g for master of puppets??
anshulkarn 3 years ago
hehe..i really dont know abt the korg ax10g...and i dont play metal..so i wouldnt know abt the patch for MoP
getvicky13 3 years ago
You can just make them by trying.. Else you can try the standard setting 15,3. that one mean distortion!
2,3 sounds also pretty evil :D
hamdengo 3 years ago
whops.. didnt see you wrote ax10g.. thought it was ax3000g. never mind :P
hamdengo 3 years ago
does this have good in between sounds like SRV style?
stevieVantanna 3 years ago
well, i guess you can get close with the Vox AC 30 amp model. I wont say that you can replicate tones, coz with any processor, you can only model the 'tone' of an amp, and not the dynamics of the amp. Simply put, you can sound like you're playing a Fender Bassman, or Vox AC30, but you just wont feel it.
getvicky13 3 years ago
ok thank you, what is the first song ?
thedarkparadise 3 years ago
that first song which i played is 'Superfantastic' by Mr.Big. The other songs are all my own riffs and licks..
getvicky13 3 years ago
hey, what is your guitar ?
thedarkparadise 3 years ago
for this demo, i used an ibanez grg 270.
getvicky13 3 years ago
dude i have one of these too please, please can u giv me the parameters u used for the acoustic the clean chorus the mild/crunch and the high gain, please dude reply id really aprecciate man im a rookie guitar player looking for a good sound
Soulfrax88 3 years ago
That's all the patches in this video, excepting the hard rock patch!!!
look around somewhere in this thread man. i think i've given some parameters here. besides, since you're a rookie, now is the time when you should really start trying to get your own sound. dont limit yourself to what i've done. figure things out for yourself man.
getvicky13 3 years ago
Very nice!!! Can you give me your presets for High gain rhythm tone and High Gain Lead??? It would be very nice...i have the board since a few hours...
fortuna