Build video: The $10 RC nitro plane made from coreflute (part 2 of 3)

[luskavarna]

need a 3rd video!!!.

[My767676]

Use your wife's scissors,the ones she uses for sewing,USA,Says ,SINGER.She will understand,with a smile,and she will iron it all out,with a tire iron.

[lwialam12]

great plane .where is part 3 ?

.

[princeibrahim1]

HI, WHERE IS build video: the $10 rc nitro plane made from coreflute part 3 ? PLEASE SEND ME THE LINK AND PLANS FOR IT. tHANKS.

[bdgar6214]

Great looking plane. Could do one to look like a Nieuport 17 fighter. By the way, where is part 3 of how to finish the plane? Thanks

[beeman1049]

i cant find the therd vid :(



[dylmey]

I couldn't find video three so I improvised. The only thing I need help with what was done with the wire wing supports. Are they just hot glued in as well as are any of them connected? Open to suggestions for this part of the build.

Thanks

[alister357]

@edwinsdad were do you get it in the uk

[usarmyfl1]

Nice videos. I know it has been asked a million times, but do you have any ETA on part 3?

[MrROTD]

lolz that's where all the real estate signs went XD

[mcnicole2913]

I like all your video but pleas make the part 3 I'm begging you sir pleas make you have to finish this for your fan😔😔😔😔😔😔😔😔😔

[smoky252]

can you use craft wood instead?

[wolfe1970]

when will part 3 be loaded plz ??

[wnainebog]

Can't find part one....

[RCllamadude]

WHEN WILL PART 3 BE UP?!?!?!?!?

[philjang]

checkout RC model reviews forum Corflute Biplane

[Brick01994]

When will part three be uploaded?



[staora]

or list of parts form hobbyking

[CLSSY56]

When can we expect part #3? I just found my Cox 049 that I had when I was a kid.

[JRAllen1023]

Where can I find part three of the bi plane and the plans. I am trying to do this for my 11 year old daughters school project...

Thanks, Jamie Allen

[RCllamadude]

@JRAllen1023 i love how you say that YOU are doing HER project. ;)

[davidsrcs]

just give the whole damn thing a wipe down! thats what she said!!!!!!!!

[brackdog]

PART 3 !!!!!!!!!!!! PLEASE please

[northseacowboy]

where is part 3!!!! I WAS just enjoying that pah!

[av8torish]

I can not find #3 in the series and Ive already seen the  finished airplane flying . Dont know why I cant find part #3

[hope4rc]

WHERE IS PART 3 OF THE BUILD. HOW DO WINGS GO ON THE BODY?

nut4rc.air

[hope4rc]

WHERE IS PART 3 OF THE BUILD. HOW DO WINGS GO ON THE BODY?

[dvowens1]

for some reason i can not find the video where you put the gas tank and the motor ...... well the plane together really i found part 1 & 2

[brackdog]

please please part 3

[flanaghanstuff]

were is part 3, please put it up so i can finish, also can i use the this but with the elec? 

[gabrielbenitosobrino]

¿¿¿¿¿ la parte 3 de 3?????

[RCcarWIZERD]

can you build it out of cardboard???????

[bucket446]

hey could you pretty please put up part 3, my plane is waiting to be finished

[nitroairplane]

I just took down some real estate signs for one of these about an hour ago

[staora]

Where is plans and part 3 ?

[AUSSIEBUDDIES]

come on already im dying to finish my plane

[brackdog]

Looking forward to part 3 as i have everything cut and glued ready for the next stage.

Easy build so far for a first time builder

[daristizs]

xjet, could you post a complete part list for an electric one? One of my relatives is right now in the U.S.A and is coming back in a couple of weeks, so i want to order online make him bring me the parts to my country ( where is more difficult o find). Thanks a lot

[xjet]

@daristizs It'll have to wait until I've tried the motors I have here to establish what is the best option. It's 4 degrees right now with a misty rain and the same is forecast for tomorrow but hopefully the weather will clear on Monday.

[jprridolfi]

When is the next part coming out???

Nice videos!!!

[trexter67]

What is the max size of the plane I can do with the same engine and same style plane just bigger to handle more weight because I can't afford all the servos but I have some others but they are much bigger and heavier and I will need more lift

[iDan1el]

Would anybody suggest what type of motor I need if I want to go electric?

[3dkat1]

Sweet , I should have a couple of motors on the way for the build :)

[jamesv2811]

Great video it made me laugh....lots

[MrWitling]

Will you be doing a video of the same type of plane but elec.

[xjet]

@MrWitling yes I will.

[seansmp420]

HAHAHAAHA I have been watching for this vid only what?, 3 months in the making M8 good job.... i am thinking about joining you on the island under the island down under and was wondering what should a settler coming to NZ be bringing? i have read what your goverment says i should have; but i figured i would ask a man who lives there. if you were coming from america what is needed to support life down there?

[xjet]

@seansmp420 Email me and I'll send you a long list :-)

[elliott7531]

@xjet When is part 3 commming?

[48horijoe]

@seansmp420 a sense of humour and a happy disposition. Heaps of models and fly mode 2

[kiwibob72]

@seansmp420 A 120-240volt power adapter would be a good place to start, we run a 240 volt mains power system over here, which could 'slightly' ruin all your chargers etc if not handled correctly. Secondly, a laid back and not too stressed approach to life will help you go a long way if you decide to go anywhere other than Auckland! - Thirdly, a love and in depth knowledge of Rugby will allow you to fit into most levels of society ;)

[arsitama]

I don't see part one of this video

[xjet]

@arsitama There is a link to it in the description.

[Bellbuoy144]

Why not use masking tape to hold the parts while gluing? Saves the wear and tear on the fingers.

[vattenskoterchaffor]

How is it going with the "jet pack" project? :)

[flyingchimp99]

weres the rest of those ' build a pulsejet videos' ?

[xjet]

@flyingchimp99 Coming... just have to make sure I've still got a workshop/hangar in which to build them first.

[eryn4586]

Has anyone put in an electric motor? If so what electric motor has worked for this project?

[xjet]

@eryn4586 I will be doing an electric version of this model in part 3 of the build. the differences are very minor.

[rideordie650r]

you have sparked my imagination. i will have plenty of this material to make some planes come election season lol. they litter every roadside with obummer signs and whatever nincompoop the republicans get to run. On that note Ron Paul 2012

[vanepico]

It's called Correx in the UK :) It's what the tail of my first ever plane was made out of :)

[ASSMYLICK]

your in NZ and we use Mertic. 

[xjet]

@ASSMYLICK True, but I'm old and we were bought up using cubits, chains and furlongs ;-)

[ASSMYLICK]

@xjet Bruce your not that old. remember i have met you before. by the way is there anything happening at the SWMAC next weekend?

[xjet]

@ASSMYLICK Hey, don't let these handsome young looks fool you :-) So long as the weather's not snow, rain or gale-force winds, the SWMAC will be operating as usual.

[jonno85uk]

@xjet "The metric system is the tool of the devil. My car gets fourty rods to the hogs head and that's the way I likes it!"

[jgilk1]

coreflute, fluteboard, coroplast... it all depends on the manucacture... basically it's cardboard made of high density plastic (a lot of polotical campaign signs are made of it).... brb i found a source of free material

[JollySwagman2006]

Coming along nicely Bruce

[MrJED698]

Great Video, You should cut a slit in the back and put the elevator in , instead of underneath.

[SubatomicMD]

:) Great video...

[degimedia]

Nice going!

[pimpflea]

Great Video! Do you think coreflute would be too heavy to try and build a average to small sized trainer with, or would it need a aerofoil wing?

[xjet]

@pimpflea To get strength into a larger wing you need to make an airfoil section but go do a google and YouTube search for SPAD RC planes and you'll see how well they can be made to fly, even in larger sizes.

[raabgunner]

Great but due to you tubes new design, can you post a link to part one in the description please..

[xjet]

@raabgunner Done

[rideordie650r]

@raabgunner don't you just hate the new youtube design. many videos have links that are hard to click on now.

[hypnolobster]

Gotten a chance to finish up the flying trainer replacement?

Damned winter.

[pyronathanpyro]

wow the title says nitro wont the plane shake apart lol

[xjet]

@pyronathanpyro No, check out the video on this channel titled "The nitro-powered parkflier RC model plane you can build in 20 minutes for $10"

[pyronathanpyro]

@xjet ok tah and now u say park flyer i see that it is a parkflying model so electric version of a nitro park flier :)

[matthewdiscovery1]

BTW where did u get a Cox engine? Or did u just have it laying around?

[xjet]

@matthewdiscovery1 Check the other vids on this channel -- I got the Cox brand-new from Cox International.

[TestECull]

@matthewdiscovery1 Coxinternational dot ca

[matthewdiscovery1]

6:35 will sandpaper work?

[xjet]

@matthewdiscovery1 Not sure. Try it out on some scrap and see if the hotglue sticks properly.

[48horijoe]

will it fly if you use a metric rule? not many things measured in inches these days eh Deb??. and I like the red its hides the blood. Only prob I see is the tower is red and white it may disappear when it hits.

[xenothius]

yes wipe the "Damn thing" down good :) nice vid

[chiosex]

About bloody time! Lol, love your vids, been waiting a while on this! Must be winter there or something..... Looking forward to the plans. Keep up the great work.

[CAShotKing]

first :D yay